Chemically Stable Styrenic Electrospun Membranes with Tailorable Surface Chemistry

Membranes with tailorable surface chemistry have applications in a wide range of industries. Synthesizing membranes from poly(chloromethyl styrene) directly incorporates an alkyl halide surface-bound initiator which can be used to install functional groups via SN2 chemistry or graft polymerization techniques. In this work, poly(chloromethyl styrene) membranes were synthesized through electrospinning. After fabrication, membranes were crosslinked with a diamine, and the chemical resistance of the membranes was evaluated by exposure to 10 M nitric acid, ethanol, or tetrahydrofuran for 24 h. The resulting membranes had diameters on the order of 2-5 microns, porosities of >80%, and permeance on the order of 10,000 L/m2/h/bar. Crosslinking the membranes generally increased the chemical stability. The degree of crosslinking was approximated using elemental analysis for nitrogen and ranged from 0.5 to 0.9 N%. The poly(chloromethyl styrene) membrane with the highest degree of crosslinking did not dissolve in THF after 24 h and retained its high permeance after solvent exposure. The presented chemically resistant membranes can serve as a platform technology due to their versatile surface chemistry and can be used in membrane manufacturing techniques that require the membrane to be contacted with organic solvents or monomers. They can also serve as a platform for separations that are performed in strong acids.

Flexible Chemiresistive Cyclohexanone Sensors Based on Single-Walled Carbon Nanotube-Polymer Composites

We report a chemiresistive cyclohexanone sensor on a flexible substrate based on single-walled carbon nanotubes (SWCNTs) functionalized with thiourea (TU) derivatives. A wrapper polymer containing both 4-vinylpyridine (4VP) groups and azide groups (P(4VP-VBAz)) was employed to obtain a homogeneous SWCNT dispersion via noncovalent functionalization of SWCNTs. The P(4VP-VBAz)-SWCNT composite dispersion was then spray-coated onto an organosilanized flexible poly(ethylene terephthalate) (PET) film to achieve immobilizing quaternization between the pyridyl groups from the polymer and the functional PET substrate, thereby surface anchoring SWCNTs. Subsequent surface functionalization was performed to incorporate a TU selector into the composites, resulting in P(Q4VP-VBTU)-SWCNT, for the detection of cyclohexanone via hydrogen bonding interactions. An increase in conductance was observed as a result of the hydrogen-bonded complex with cyclohexanone resulting in a higher hole density and/or mobility in SWCNTs. As a result, a sensor device fabricated with P(Q4VP-VBTU)-SWCNT composites exhibited chemiresistive responses (ΔG/G₀) of 7.9 ± 0.6% in N₂ (RH 0.1%) and 4.7 ± 0.4% in air (RH 5%), respectively, upon exposure to 200 ppm cyclohexanone. Selective cyclohexanone detection was achieved with minor responses (ΔG/G₀ < 1.4% at 500 ppm) toward interfering volatile organic compounds (VOC). analytes. We demonstrate a robust sensing platform using the polymer-SWCNT composites on a flexible PET substrate for potential application in wearable sensors.

The Fabrication of Poly(Σ-caprolactone)-Poly(ethylene oxide) Sandwich Type Nanofibers Containing Sericin-Capped Silver Nanoparticles as an Antibacterial Wound Dressing

In this study, antibacterial, synthetic poly(Σ-caprolactone)-poly(ethylene oxide) (PCL-PEO) multilayer nanofibers were produced by an electrospinning method. The material was synthesized in 3 layers. The upper-lower protective layers were produced by PCL nanofibers and the intermediate layer was produced from PEO nanofiber containing sericin-capped silver nanoparticles (S-AgNPs). The electrospinning conditions in which nano-sized, smooth, bead-free fibers were obtained was determined to be an applied voltage of 20 kV, a flow rate of 8 μL/min and a distance between the collector and the needle tip of 22 cm for the PCL layer (dissolved at a 12% g/mL concentration in a chloroform:methanol (3:2) solvent mixture) layer. For the S-AgNPs doped PEO layer (dissolved at a 3.5% g/mL concentration in water), the corresponding conditions were determined to be 20 kV, 15 μL/min and 20 cm. To characterize the three-layer material that consisted of PCL and S-AgNPs doped PEO layers, FTIR and SEM analyses were performed, and the water retention capacity, in situ degradability and antibacterial activity of the material was investigated. According to SEM analysis, the fibers obtained were found to be nano-sized, smooth and bead-free and the average size of the nanofibers forming the PCL layer was 687 nm while the average size of the fibers forming the PEO layer was 98 nm. Antibacterial activity tests were performed using gram-positive (Staphylococcus aureus ATCC 6538) and gram-negative (Escherichia coli ATCC 25922) bacteria and the resulting biomaterial was found to have antimicrobial effect on both gram-negative and gram-positive bacteria. It was determined that the 3-layer material obtained in this study can be used as a wound dressing.

Surface Modification of Intraocular Lens with Hydrophilic Poly(Sulfobetaine Methacrylate) Brush for Posterior Capsular Opacification Prevention

Purpose: The intraocular lens (IOL) is a common, yet important, implantable device used in treatment of cataract in clinics. However, the unexpected adhesion of postoperative residual lens epithelial cells (LECs) often causes serious complications, such as posterior capsular opacification (PCO), which lead to vision loss again. In this investigation, a poly(sulfobetaine methacrylate) (PSBMA) brush coating was fabricated on an IOL to generate a hydrophilic surface coating on the IOL for enhanced cell adhesion resistance so as to decrease PCO incidence. Methods: The PSBMA brush coating on the IOL surface was fabricated using surface-initiated reversible addition-fragmentation chain transfer polymerization. X-ray photoelectron spectroscopy (XPS) was used to demonstrate the surface coating preparation. The water contact angle (WCA) measurement was used to test surface hydrophilicity. In vitro LEC culture was use to evaluate the cell behavior on the IOL material surfaces, with or without PSBMA coating modification. Finally, animal cataract surgeries were carried out to evaluate in vivo biocompatibilities and anti-PCO effects. Results: The XPS and WCA measurements illustrate successful surface modification and good surface hydrophilicity. The in vitro cell culture results show that the hydrophilic PSBMA polymer brush coating evidently decreases adhesion and proliferation of LECs. Results of the in vivo cataract surgery with intraocular implantation show that PSBMA modification on the IOL surface does not induce side effects in nearby tissues, whereas posterior capsular hyperplasia can be evidently reduced. Conclusion: The PSBMA brush surface-modified IOL has good in vivo biocompatibility and it can effectively reduce the incidence of postoperative PCO.

Film Properties and Antimicrobial Efficacy of Quaternized PDMAEMA Brushes: Short vs Long Alkyl Chain Length

Quaternized poly(2-(dimethylamino)ethyl methacrylate) (PDMAEMA) brushes bearing quaternary ammonium groups of different alkyl chain lengths (ACLs) were prepared and assessed as biocidal coatings. For the synthesis of the antimicrobial brushes, first well-defined PDMAEMA chains were grown by surface-initiated atom transfer radical polymerization on glass and silicon substrates. Next, the tertiary amine groups of the polymer brushes were modified via a quaternization reaction, using alkyl halides, to obtain the cationic polymers. The polymer films were characterized by Fourier-transform infrared spectroscopy, ellipsometry, atomic force microscopy, and water contact angle measurements. The effect of the ACL of the quaternary ammonium groups on the physicochemical properties of the films as well as the contact killing efficiency of the surfaces against representative Gram-positive and Gram-negative bacteria was investigated. A hydrophilic to hydrophobic transition of the surfaces and a significant decrease of the degree of quaternization of the DMAEMA moieties was found upon increasing the ACL of the quaternization agent above six carbon atoms, allowing the wettability, the thickness, and the pH-response of the brushes to be tuned via a facile postpolymerization, quaternization reaction. At the same time, antimicrobial tests revealed that the hydrophilic polymer brushes exhibited enhanced bactericidal activity against Escherichia coli and Bacillus cereus, whereas the hydrophobic surfaces showed a significant deterioration of the in vitro bactericidal performance. Our results elucidate the antimicrobial action of quaternized polymer brushes, dictating the appropriate choice of the ACL of the quaternization agent for the development of coatings that effectively inhibit biofilm formation on surfaces.

Electrospun Polyethylene Terephthalate Nanofibers Loaded with Silver Nanoparticles: Novel Approach in Anti-Infective Therapy

Polyethylene terephthalate (PET) is a major pollutant polymer, due to its wide use in food packaging and fiber production industries worldwide. Currently, there is great interest for recycling the huge amount of PET-based materials, derived especially from the food and textile industries. In this study, we applied the electrospinning technique to obtain nanostructured fibrillary membranes based on PET materials. Subsequently, the recycled PET networks were decorated with silver nanoparticles through the chemical reduction method for antimicrobial applications. After the characterization of the materials in terms of crystallinity, chemical bonding, and morphology, the effect against Gram-positive and Gram-negative bacteria, as well as fungal strains, was investigated. Furthermore, in vitro and in vivo biocompatibility tests were performed in order to open up potential biomedical applications, such as wound dressings or implant coatings. Silver-decorated fibers showed lower cytotoxicity and inflammatory effects and increased antibiofilm activity, thus highlighting the potential of these systems for antimicrobial purposes.

Infections associated with mesh repairs of abdominal wall hernias: Are antimicrobial biomaterials the longed-for solution?

The incidence of mesh-related infection after abdominal wall hernia repair is low, generally between 1 and 4%; however, worldwide, this corresponds to tens of thousands of difficult cases to treat annually. Adopting best practices in prevention is one of the keys to reduce the incidence of mesh-related infection. Once the infection is established, however, only a limited number of options are available that provides an efficient and successful treatment outcome. Over the past few years, there has been a tremendous amount of research dedicated to the functionalization of prosthetic meshes with antimicrobial properties, with some receiving regulatory approval and are currently available for clinical use. In this context, it is important to review the clinical importance of mesh infection, its risk factors, prophylaxis and pathogenicity. In addition, we give an overview of the main functionalization approaches that have been applied on meshes to confer anti-bacterial protection, the respective benefits and limitations, and finally some relevant future directions.

Surface-Initiated Controlled Radical Polymerization: State-of-the-Art, Opportunities, and Challenges in Surface and Interface Engineering with Polymer Brushes

The generation of polymer brushes by surface-initiated controlled radical polymerization (SI-CRP) techniques has become a powerful approach to tailor the chemical and physical properties of interfaces and has given rise to great advances in surface and interface engineering. Polymer brushes are defined as thin polymer films in which the individual polymer chains are tethered by one chain end to a solid interface. Significant advances have been made over the past years in the field of polymer brushes. This includes novel developments in SI-CRP, as well as the emergence of novel applications such as catalysis, electronics, nanomaterial synthesis and biosensing. Additionally, polymer brushes prepared via SI-CRP have been utilized to modify the surface of novel substrates such as natural fibers, polymer nanofibers, mesoporous materials, graphene, viruses and protein nanoparticles. The last years have also seen exciting advances in the chemical and physical characterization of polymer brushes, as well as an ever increasing set of computational and simulation tools that allow understanding and predictions of these surface-grafted polymer architectures. The aim of this contribution is to provide a comprehensive review that critically assesses recent advances in the field and highlights the opportunities and challenges for future work.

Amidation of Polyesters Is Slow in Nonaqueous Solvents: Efficient Amidation of Poly(ethylene terephthalate) with 3-Aminopropyltriethoxysilane in Water for Generating Multifunctional Surfaces

This paper describes surface functionalization of poly(ethylene terephthalate) (PET) films by transamidation of the ester groups with primary amines. The use of water as a solvent improves tremendously the reaction rate and yield compared to conventionally used alcohols. In this study, PET films were exposed to an aqueous solution of 3-aminopropyltriethoxysilane (APTES), which resulted in ester-to-amide reactions on the surface of the film. Hydrolysis of the resulting ethoxy moieties in APTES creates hydroxyl groups that can be used as anchoring points for further modification of PET films. This scheme offers an alternative approach to modify polyesters using water as the solvent.

Controlling integrin-based adhesion to a degradable electrospun fibre scaffold via SI-ATRP

While polycaprolactone (PCL) and similar polyesters are commonly used as degradable scaffold materials in tissue engineering and related applications, non-specific adsorption of environmental proteins typically precludes any control over the signalling pathways that are activated during cell adhesion to these materials. Here we describe the preparation of PCL-based fibres that facilitate cell adhesion through well-defined pathways while preventing adhesion via adsorbed proteins. Surface-initiated atom transfer radical polymerisation (SI-ATRP) was used to graft a protein-resistant polymer brush coating from the surface of fibres, which had been electrospun from a brominated PCL macroinitiator. This coating also provided alkyne functional groups for the attachment of specific signalling molecules via the copper-mediated azide-alkyne click reaction; in this case, a cyclic RGD peptide with high affinity for α_vβ₃ integrins. Mesenchymal stem cells were shown to attach to the fibres via the peptide, but did not attach in its absence, nor when blocked with soluble peptide, demonstrating the effective control of cell adhesion pathways.

Copolymer Brushes with Temperature-Triggered, Reversibly Switchable Bactericidal and Antifouling Properties for Biomaterial Surfaces

The adherence of bacteria and the formation of biofilm on implants is a serious problem that often leads to implant failure. A series of antimicrobial coatings have been constructed to resist bacterial adherence or to kill bacteria through contact with or release of antibacterial agents. The accumulation of dead bacteria facilitates further bacterial contamination and biofilm development. Herein, we have designed and constructed a novel, reversibly switchable bactericidal and antifouling surface through surface-initiated reversible addition-fragmentation chain transfer (RAFT) polymerization to combine thermally responsive N-isopropylacrylamide (NIPAAm) and bactericidal quaternary ammonium salts (2-(dimethylamino)-ethyl methacrylate (DMAEMA⁺)). Measurements of spectroscopic ellipsometry and water contact angle and X-ray photoelectron spectroscopy were used to examine the process of the surface functionalization. The temperature-responsive P(DMAEMA⁺-co-NIPAAm) copolymer coating can switch by phase transition between a hydrophobic capturing surface at high temperatures and a relatively hydrophilic antifouling surface at lower temperatures. The quaternary ammonium salts of PDMAEMA⁺ displayed bactericidal efficiency against both Escherichia coli and Staphylococcus aureus. The functionalized surface could efficiently prevent bovine serum albumin adsorption and had good biocompatibility against human lens epithelial cells.

Multipurpose Polymeric Coating for Functionalizing Inert Polymer Surfaces

In this work, we report on the development of a highly functionalizable polymer coating prepared by the chemical coupling of trichlorosilane (TCS) to the vinyl groups of poly(vinylmethyl siloxane) (PVMS). The resultant PVMS-TCS copolymer can be coated as a functional organic primer layer on a variety of polymeric substrates, ranging from hydrophilic to hydrophobic. Several case studies demonstrating the remarkable and versatile properties of PVMS-TCS coatings are presented. In particular, PVMS-TCS is found to serve as a convenient precursor for the deposition of organosilanes and the subsequent growth of polymer brushes, even on hydrophobic surfaces, such as poly(ethylene terephthalate) and polypropylene. In this study, the physical and chemical characteristics of these versatile PVMS-TCS coatings are interrogated by an arsenal of experimental probes, including scanning electron microscopy, water contact-angle measurements, ellipsometry, Fourier-transform infrared spectroscopy, X-ray photoelectron spectroscopy, and near-edge X-ray absorption fine structure spectroscopy.

Microporous organic network@PET hybrid membranes: removal of minute organic pollutants dissolved in water

Microporous organic networks (MONs) were incorporated into a polyethylene terephthalate (PET) membrane. The resultant MON@PET hybrid membranes showed promising filtration towards aromatic pollutants dissolved in water.

Direct surface modification of poly(VDF-co-TrFE) films by surface-initiated ATRP without pretreatment

A NMR study revealed that the surface-initiated ATRP of tBA occurred due to fluorine abstraction from the TrFE units of poly(VDF-co-TrFE).

Multiple types of hydroxyl-rich cationic derivatives of PGMA for broad-spectrum antibacterial and antifouling coatings

A series of hydroxyl-rich quaternized polymers with Ag ions have been proposed for broad-spectrum antibacterial and antifouling coatings.

Quaternized poly(2-(dimethylamino)ethyl methacrylate)-grafted agarose copolymers for multipurpose antibacterial applications

Polymeric quaternary ammonium salts-functionalized agarose not only exhibit good antibacterial activity in solution form, but also can be solidified to construct antibacterial surfaces.