Integration of acoustic micromixing with cyclic olefin copolymer microfluidics for enhanced lab-on-a-chip applications in nanoscale liposome synthesis

The integration of acoustic wave micromixing with microfluidic systems holds great potential for applications in biomedicine and lab-on-a-chip technologies. Polymers such as cyclic olefin copolymer (COC) are increasingly utilized in microfluidic applications due to its unique properties, low cost, and versatile fabrication methods, and incorporating them into acoustofluidics significantly expands their potential applications. In this work, for the first time, we demonstrated the integration of polymer microfluidics with acoustic micromixing utilizing oscillating sharp edge structures to homogenize flowing fluids. The sharp edge mixing platform was entirely composed of COC fabricated in a COC-hydrocarbon solvent swelling based microfabrication process. As an electrical signal is applied to a piezoelectric transducer bonded to the micromixer, the sharp edges start to oscillate generating vortices at its tip, mixing the fluids. A 2D numerical model was implemented to determine the optimum microchannel dimensions for experimental mixing assessment. The system was shown to successfully mix fluids at flow rates up to 150µl h-1and has a modest effect even at the highest tested flow rate of 600µl h-1. The utility of the fabricated sharp edge micromixer was demonstrated by the synthesis of nanoscale liposomes.

Microwave-Assisted Solvent Bonding for Polymethyl Methacrylate Microfluidic Device

This paper demonstrated a microwave-assisted solvent bonding method that uses organic solvent to seal the thermoplastic substrates with microwave assistance. This direct bonding is a simple and straightforward process that starts with solvent application followed by microwave irradiation without the need for expensive facilities or complex procedures. The organic solvent applied at the bonding interface is used in dissolving and dielectric heating of the thermoplastic surfaces to seal the thermoplastic substrates under microwave assistance. We evaluated acetone and ethanol to seal the polymethyl methacrylate (PMMA) microfluidic device. The bonding performance, such as bonding coverage, geometry stability, and bonding strength (tensile) were observed and compared with the oven-heating and non-heating control experiments under the same force applications. Results showed that the microwave-assisted solvent bonding method presents a high bonding yield (maximum > 99%) and bonding strength (maximum ~2.77 MPa) without microchannel distortion, which can be used for various microfluidic applications.

A practical approach for the optimization of channel integrity in the sealing of shallow microfluidic devices made from cyclic olefin polymer

A reduced channel height in microfluidic Lab-on-a-Chip (LOC) devices enables a reduction in the required volume of sample and reagents. LOC devices are most often manufactured by microstructuring a planar substrate and subsequently sealing it with a cover film. However, shallow chip designs, made from polymers, are sensitive to channel deformation during the sealing of the microfluidic device. Inappropriate bonding conditions often result in the loss of the microfluidic functionality. A systematic and practical approach for the identification of suitable bonding process parameters is missing. In this article, a straightforward approach for the optimization of channel integrity in the sealing of shallow microfluidic devices made from Cyclic Olefin Polymer (COP) is presented. Two COP materials were tested: COP Zeonex 690R (Glass transition temperature T_g = 135 °C) both as a cover film and substrate material, and COP ZF14 (T_g = 135 °C) as a film material. A mechanical analysis using microstructured Zeonex 690R substrates was performed to generate a matrix of low-distortion bonding parameters, including temperature, pressure and time. The well-established method of solvent-assisted bonding was used to enhance the characteristically low bond strengths of the native COP material. In addition, plasma-assisted bonding was tested and compared. The optimization approach was validated by the manufacture of a microfluidic test device, the demonstration of its microfluidic functionality, and the quantitative evaluation of the achieved channel integrity.

Magnetic microparticle-polydimethylsiloxane composite for reversible microchannel bonding

In this study, an iron oxide magnetic microparticles and poly(dimethylsiloxane) (MMPs-PDMS) composite material was employed to demonstrate a simple high-strength reversible magnetic bonding method. This paper presents the casting of opaque-view (where optical inspection through the microchannels was impossible) and clear-view (where optical inspection through the microchannel was possible) MMPs-PDMS. The influence of the microchannel geometries on the casting of the opaque-view casting was limited, which is similar to standard PDMS casting. Clear-view casting performance was highly associated with the microchannel geometries. The effects of the microchannel layout and the gap between the PDMS cover layer and the micromold substrate were thoroughly investigated. Compared with the native PDMS bonding strength of 31 kPa, the MMPs-PDMS magnetic bonding experiments showed that the thin PDMS film with an MMPs-PDMS layer effectively reduced the surface roughness and enhanced MMPs-PDMS reversible magnetic bonding strength. A thin PDMS film-coated opaque-view MMPs-PDMS device exhibited the greatest bonding strength of 110 kPa, and a clear-view MMPs-PDMS device with a thin PDMS film attained a magnetic bonding strength of 81 kPa.