Bioactive and biomimetic 3D scaffolds for bone tissue engineering using graphitic carbon nitride as a sustainable visible light photoinitiator

Graphitic carbon nitride (g-C3N4) is explored as a novel sustainable visible light photoinitiator for the preparation of biomimetic 3D hydrogel scaffolds comprising gelatin methacrylamide (GelMA) and dopamine methacrylamide for use in tissue engineering. The initiator efficiency was assessed by comparing the swelling behavior and the stability of photopolymerized hydrogels prepared with GelMA of different degrees of functionalization and different comonomer compositions. Bioactive composite hydrogels with a 50 wt% nanohydroxyapatite (nHAp) content, to closely mimic the actual bone composition, were successfully obtained by the introduction of nHAp in the prepolymer solutions followed by photopolymerization. The composite hydrogels demonstrated enhanced mechanical properties and excellent stability in PBS verifying the preparation of robust 3D scaffolds for use in cancellous or pre-calcified bone tissue engineering applications. The in vitro cell response of the composite scaffolds exhibited high cell viability and enhanced differentiation of pre-osteoblasts to mature osteoblasts, demonstrating their osteogenic potential. This work establishes, for the first time, the excellent properties of g-C3N4 as a sustainable, visible light initiator, fully satisfying the principles of green chemistry, for the preparation of robust and biologically relevant hydrogels, and proposes a new approach to overcome the main challenges of conventional photoinitiators in cell scaffold fabrication, such as photobleaching, high cost and non-scalable synthesis employing toxic organic precursors and solvents.

Prestrain Programmable 4D Printing of Nanoceramic Composites with Bioinspired Microstructure

Four-dimensional (4D) printing enables programmable, predictable, and precise shape change of responsive materials to achieve desirable behaviors beyond conventional three-dimensional (3D) printing. However, applying 4D printing to ceramics remains challenging due to their intrinsic brittleness and inadequate stimuli-responsive ability. Here, this work proposes a conceptional combination of bioinspired microstructure design and a programmable prestrain approach for 4D printing of nanoceramics. To overcome the flexibility limitation, the bioinspired concentric cylinder structure in the struts of 3D printed lattices are replicated to develop origami nanoceramic composites with high inorganic content (95 wt%). Furthermore, 4D printing is achieved by applying a programmed prestrain to the printed lattices, enabling the desired deformation when the prestrain is released. Due to the bioinspired concentric cylinder microstructures, the printed flexible nanoceramic composites exhibit superior mechanical performance and anisotropic thermal management capability. Further, by introducing oxygen vacancies to the ceramic nanosheets, conductive nanoceramic composites are prepared with a unique sensing capability for various sensing applications. Hence, this research breaks through the limitation of ceramics in 4D printing and achieves high-performance shape morphing materials for applications under extreme conditions, such as space exploration and high-temperature systems.

Visible-Light-Mediated Nano-biomineralization of Customizable Tough Hydrogels for Biomimetic Tissue Engineering

Biomineralized tough hydrogels (BTHs) have advanced applications in the fields of soft bioelectronics and biomimetic tissue engineering. But the development of rapid and general photomineralization strategies for one-step fabrication of customizable BTHs is still a challenging task. Here we report a straightforward, low-cost visible-light-mediated nano-biomineralization (VLMNB) strategy via a rational design of a phosphate source and efficient ruthenium photochemistry. Multinetwork tough hydrogels are simultaneously constructed under the same condition. Therefore, BTHs are rapidly prepared in a short time as low as ∼60 s under visible light irradiation. The in situ formation of calcium phosphate particles can improve BTHs' mechanical and biological properties and reduce the friction coefficient with bones. Furthermore, fast biomineralization and solidification processes in these BTHs benefit their injectable and highly flexible customizable design, showing applications of promoting customizable skin repair and bone regeneration.

Diffusion-Controlled Crystallization of Calcium Phosphate in a Hydrogel toward a Homogeneous Octacalcium Phosphate/Agarose Composite

Diffusion-controlled crystallization in a hydrogel has been investigated to synthesize organic/inorganic hybrid composites and obtain a fundamental understanding of the detailed mechanism of biomineralization. Although calcium phosphate/hydrogel composites have been intensively studied and developed for the application of bone substitutes, the synthesis of homogeneous and integrated composites remains challenging. In this work, diffusion-controlled systems were optimized by manipulating the calcium ion flux at the interface, concentration gradient, and diffusion coefficient to synthesize homogeneous octacalcium phosphate/hydrogel composites with respect to the crystal morphology and density. The ion flux and local pH play an important role in determining the morphology, density, and phase of the crystals. This study suggests a model system that can reveal the relation between local conditions and the resulting crystal phase in diffusion-limited systems and provides a synthetic method for homogeneously organized organic/inorganic composites.

Self-Organized Spatiotemporal Mineralization of Hydrogel: A Simulant of Osteon

Nature creates fascinating self-organized spatiotemporal patterns through the delicate control of reaction-diffusion dynamics. As the primary unit of cortical bone, osteon has concentric lamellar architecture, which plays a crucial role in the mechanical and physiological functions of bone. However, it remains a great challenge to fabricate the osteon-like structure in a natural self-organization way. Taking advantage of the nonequilibrium reaction in hydrogels, a simple mineralization strategy to closely mimic the formation of osteon in a mild physiological condition is developed. By constructing two reverse concentration gradients of ions from periphery to interior of cylindrical hydrogel, spatiotemporal self-organization of calcium phosphate in concentric rings is generated. It is noteworthy that minerals in different layers possess diverse contents and crystalline phases, which further guide the adhesion and spread of osteoblasts on these patterns, resembling the architecture and cytological behavior of osteon. Besides, theoretical data indicates the predominate role of ion concentrations and pH values of solution, in good accordance with experimental results. Independent of precise instruments, this lifelike method is easily obtained, cost-efficient, and effectively imitates the mineral deposition in osteon from a physiochemical view. The strategy may be expanded to develop other functional material patterns via spatiotemporal self-organization.

Low-temperature adaptive conductive hydrogel based on ice structuring proteins/CaCl2 anti-freeze system as wearable strain and temperature sensor

Conductive hydrogels as wearable devices meet the basic demands of mechanical flexibility and smart sensing. However, achieving anti-freeze property in conductive hydrogels is still challengeable. Here, a novel anti-freezing system based on ice structuring proteins and CaCl₂ was introduced to enable a conductive hydrogel with low-temperature adaptability. Both formation of ice nuclei and ice growth of the hydrogel at sub-zero temperature could be inhibited. Supported by the anti-freeze system, the hydrogel revealed good flexibility (890% at -20 °C), recovery and conductivity (0.50 S/m at -20 °C) at both room temperature and sub-zero temperature. The low-temperature adaptability enabled the hydrogel to be used as strain and temperature sensors at both room temperature and sub-zero temperature. The anti-freeze system in this work is expected to open up a new avenue to promote the conductive hydrogel with low-temperature adaptability.

Novel Hydrogel Scaffolds Based on Alginate, Gelatin, 2-Hydroxyethyl Methacrylate, and Hydroxyapatite

Hydrogel scaffolding biomaterials are one of the most attractive polymeric biomaterials for regenerative engineering and can be engineered into tissue mimetic scaffolds to support cell growth due to their similarity to the native extracellular matrix. The novel, versatile hydrogel scaffolds based on alginate, gelatin, 2-hydroxyethyl methacrylate, and inorganic agent hydroxyapatite were prepared by modified cryogelation. The chemical composition, morphology, porosity, mechanical properties, effects on cell viability, in vitro degradation, in vitro and in vivo biocompatibility were tested to correlate the material’s composition with the corresponding properties. Scaffolds showed an interconnected porous microstructure, satisfactory mechanical strength, favorable hydrophilicity, degradation, and suitable in vitro and in vivo biocompatible behavior. Materials showed good biocompatibility with healthy human fibroblast in cell culture, as well as in vivo with zebrafish assay, suggesting newly synthesized hydrogel scaffolds as a potential new generation of hydrogel scaffolding biomaterials with tunable properties for versatile biomedical applications and tissue regeneration.

Hidrogeles de colágeno acoplados con hidroxiapatita para aplicaciones en ingeniería tisular

Los hidrogeles basados en colágeno son redes tridimensionales (3D) con la capacidad de absorber agua y una alta biocompatibilidad para utilizarlos en la reparación de tejidos dañados. Estos materiales presentan pobres propiedades mecánicas y velocidades de degradación rápidas, limitando su aplicación a estrategias de ingeniería tisular y biomedicina; por ésto, la incorporación de fases inorgánicas en la matriz 3D del colágeno como la hidroxiapatita ha contribuido en la mejora de sus propiedades, incrementado la eficiencia de los hidrogeles híbridos obtenidos. Este trabajo, presenta las contribuciones más relevantes relacionadas con los sistemas de hidrogeles basados en colágeno y partículas de hidroxiapatita dispersas dentro de la matriz colagénica, lo que evidencia que la combinación de los materiales no altera la biocompatibilidad y biodegradabilidad típicas del colágeno, permitiendo la adhesión, proliferación, crecimiento celular y control del metabolismo de las células implicadas en los procesos de una reparación ósea, presentando a los hidrogeles como una estrategia para su uso potencial en la ingeniería tisular.

3D Freeform Printing of Nanocomposite Hydrogels through in situ Precipitation in Reactive Viscous Fluid

Composite hydrogels have gained great attention as three-dimensional (3D) printing biomaterials because of their enhanced intrinsic mechanical strength and bioactivity compared to pure hydrogels. In most conventional printing methods for composite hydrogels, particles are preloaded in ink before printing, which often reduces the printability of composite ink with little mechanical improvement due to poor particle-hydrogel interaction of physical mixing. In contrast, the in situ incorporation of nanoparticles into a hydrogel during 3D printing achieves uniform distribution of particles with remarkable mechanical reinforcement, while precursors dissolved in inks do not influence the printing process. Herein, we introduced a "printing in liquid" technique coupled with a hybridization process, which allows 3D freeform printing of nanoparticle-reinforced composite hydrogels. A viscoplastic matrix for this printing system provides not only support for printed hydrogel filaments but also chemical reactants to induce various reactions in printed objects for in situ modification. Nanocomposite hydrogel scaffolds were successfully fabricated through this 3D freeform printing of hyaluronic acid (HAc)-alginate (Alg) hydrogel inks through a two-step crosslinking strategy. The first ionic crosslinking of Alg provided structural stability during printing, while the secondary crosslinking of photo-curable HAc improved the mechanical and physiological stability of the nanocomposite hydrogels. For in situ precipitation during 3D printing, phosphate ions were dissolved in the hydrogel ink and calcium ions were added to the viscoplastic matrix. The composite hydrogels demonstrated a significant improvement in mechanical strength, biostability, as well as biological performance compared to pure HAc. Moreover, the multi-material printing of composites with different calcium phosphate contents was achieved by adjusting the ionic concentration of inks. Our method greatly accelerates the 3D printing of various functional or hybridized materials with complex geometries through the design and modification of printing materials coupled with in situ post-printing functionalization and hybridization in reactive viscoplastic matrices.

3D Freeform Printing of Nanocomposite Hydrogels through in situ Precipitation in Reactive Viscous Fluid

Composite hydrogels have gained great attention as three-dimensional (3D) printing biomaterials because of their enhanced intrinsic mechanical strength and bioactivity compared to pure hydrogels. In most conventional printing methods for composite hydrogels, particles are preloaded in ink before printing, which often reduces the printability of composite ink with little mechanical improvement due to poor particle-hydrogel interaction of physical mixing. In contrast, the in situ incorporation of nanoparticles into a hydrogel during 3D printing achieves uniform distribution of particles with remarkable mechanical reinforcement, while precursors dissolved in inks do not influence the printing process. Herein, we introduced a "printing in liquid" technique coupled with a hybridization process, which allows 3D freeform printing of nanoparticle-reinforced composite hydrogels. A viscoplastic matrix for this printing system provides not only support for printed hydrogel filaments but also chemical reactants to induce various reactions in printed objects for in situ modification. Nanocomposite hydrogel scaffolds were successfully fabricated through this 3D freeform printing of hyaluronic acid (HAc)-alginate (Alg) hydrogel inks through a two-step crosslinking strategy. The first ionic crosslinking of Alg provided structural stability during printing, while the secondary crosslinking of photo-curable HAc improved the mechanical and physiological stability of the nanocomposite hydrogels. For in situ precipitation during 3D printing, phosphate ions were dissolved in the hydrogel ink and calcium ions were added to the viscoplastic matrix. The composite hydrogels demonstrated a significant improvement in mechanical strength, biostability, as well as biological performance compared to pure HAc. Moreover, the multi-material printing of composites with different calcium phosphate contents was achieved by adjusting the ionic concentration of inks. Our method greatly accelerates the 3D printing of various functional or hybridized materials with complex geometries through the design and modification of printing materials coupled with in situ post-printing functionalization and hybridization in reactive viscoplastic matrices.

Optimizing Nanohydroxyapatite Nanocomposites for Bone Tissue Engineering

Bone tissue engineering involves the combined use of materials with functional properties to regenerate bone. Nanohydroxyapatite (nHA) can influence the behavior of cells. The functional and structural properties of nHA can be controlled during nanoparticle synthesis. This review defines the relationship between the attributes of nHA nanoparticles and their biological effects, focusing on biocompatibility, surface-area-to-volume ratio, bonding chemistry, and substrate functionality. The paper explores how these aspects have been applied in the development of scaffolds for the repair of damaged bone or regeneration of missing bone.

Dual Salt- and Thermoresponsive Programmable Bilayer Hydrogel Actuators with Pseudo-Interpenetrating Double-Network Structures

Development of smart soft actuators is highly important for fundamental research and industrial applications but has proved to be extremely challenging. In this work, we present a facile, one-pot, one-step method to prepare dual-responsive bilayer hydrogels, consisting of a thermoresponsive poly( N-isopropylacrylamide) (polyNIPAM) layer and a salt-responsive poly(3-(1-(4-vinylbenzyl)-1 H-imidazol-3-ium-3-yl)propane-1-sulfonate) (polyVBIPS) layer. Both polyNIPAM and polyVBIPS layers exhibit a completely opposite swelling/shrinking behavior, where polyNIPAM shrinks (swells) but polyVBIPS swells (shrinks) in salt solution (water) or at high (low) temperatures. By tuning NIPAM:VBIPS ratios, the resulting polyNIPAM/polyVBIPS bilayer hydrogels enable us to achieve fast and large-amplitude bidirectional bending in response to temperatures, salt concentrations, and salt types. Such bidirectional bending, bending orientation, and degree can be reversibly, repeatedly, and precisely controlled by salt- or temperature-induced cooperative swelling-shrinking properties from both layers. Based on their fast, reversible, and bidirectional bending behavior, we further design two conceptual hybrid hydrogel actuators, serving as a six-arm gripper to capture, transport, and release an object and an electrical circuit switch to turn on-and-off a lamp. Different from the conventional two- or multistep methods for preparation of bilayer hydrogels, our simple, one-pot, one-step method and a new bilayer hydrogel system provide an innovative concept to explore new hydrogel-based actuators through combining different responsive materials that allow us to program different stimuli for soft and intelligent materials applications.

Interfacial Mineral Fusion and Tubule Entanglement as a Means to Harden a Bone Augmentation Material

A new bone augmenting material is reported, which is formed from calcium-loaded hydrogel-based spheres. On immersion of these spheres in a physiological medium, they become surrounded with a sheath of precipitate, which ruptures due to a build-up in osmotic pressure. This results in the formation of mineral tubes that protrude from the sphere surface. When brought into close contact with one another, these spheres become fused through the entanglement and subsequent interstitial mineralization of the mineral tubules. The tubular calcium phosphate induces the expression of osteogenic genes (runt-related transcription factor 2 (RUNX2), transcription factor SP7 (SP7), collagen type 1 alpha 1 (COL1A1), and bone gamma-carboxyglutamic acid-containing protein (BGLAP)) and promotes the formation of mineral nodules in preosteoblast cultures comparable to an apatitic calcium phosphate phase. Furthermore, alkaline phosphatase (ALP) is significantly upregulated in the presence of tubular materials after 10 d in culture compared with control groups (p < 0.001) and sintered apatite (p < 0.05). This is the first report of a bioceramic material that is formed in its entirety in situ and is therefore likely to provide a better proxy for biological mineral than other existing synthetic alternatives to bone grafts.

Self-assembly of collagen-based biomaterials: preparation, characterizations and biomedical applications

By combining regulatory parameters with characterization methods, researchers can selectively fabricate collagenous biomaterials with various functional responses for biomedical applications.

Enhanced bone tissue regeneration using a 3D printed microstructure incorporated with a hybrid nano hydrogel

Three-dimensional (3D) functional constructs with biomimetic mechanical and chemical properties are ideal for various regenerative medicine applications. These properties of 3D fabricated constructs mainly depend on the intrinsic characteristics of the materials and fabrication method. In this respect, the current use of hydrogels for musculoskeletal tissue repair is not ideal due to the lack of suitable mechanical properties, as well as the high biomimetic requirement for success. To overcome this limitation, we developed a novel functionalized hydrogel with bioactive gold nanoparticles (GNPs), reinforcing a 3D printed microstructure via fused deposition modeling (FDM) for bone tissue regeneration. We used biodegradable thermoplastic polylactic acid (PLA) as the 3D printed microstructure in combination with photo-curable gelatin hydrogels as the encapsulation matrix for the incorporation of cyclic RGD conjugated GNPs (RGNP), and investigated their mechanical properties. In addition, human adipose-derived stem cells (ADSCs) were encapsulated within the gelatin hydrogel and examined for viability, morphology, and osteogenic differentiation in vitro. The results showed that the stiffness of the composite hydrogel on reinforcing a 3D printed microstructure can be readily modulated to simulate the stiffness of the human mandibular condyle. ADSCs encapsulated in the composite structures remained viable within the hydrogel and showed excellent spreading on the 3D printed PLA microstructure. More importantly, osteogenic differentiation with incorporated RGNPs promoted significantly higher gene expression of osteogenic specific factors. Therefore, reinforced composite hydrogels are suitable for stem cell differentiation control and bone tissue regeneration.

Highly recyclable Ag NPs/alginate composite beads prepared via one-pot encapsulation method for efficient continuous reduction of p-nitrophenol

Recyclable Ag NPs/alginate composite beads, performing well in dynamic catalytic hydrogenation of p-nitrophenol, were prepared via a one-pot encapsulation method.

Electric field-assisted formation of organically modified hydroxyapatite (ormoHAP) spheres in carboxymethylated gelatin gels

A biomimetic strategy was developed in order to prepare organically modified hydroxyapatite (ormoHAP) with spherical shape. The technical approach is based on electric field-assisted migration of calcium ions and phosphate ions into a hydrogel composed of carboxymethylated gelatin. The electric field as well as the carboxymethylation using glucuronic acid (GlcA) significantly accelerates the mineralization process, which makes the process feasible for lab scale production of ormoHAP spheres and probably beyond. A further process was developed for gentle separation of the ormoHAP spheres from the gelatin gel without compromising the morphology of the mineral. The term ormoHAP was chosen since morphological analyses using electron microscopy (SEM, TEM) and element analysis (EDX, FT-IR, XRD) confirmed that carboxymethylated gelatin molecules use to act as organic templates for the formation of nanocrystalline HAP. The hydroxyapatite (HAP) crystals self-organize to form hollow spheres with diameters ranging from 100 to 500nm. The combination of the biocompatible chemical composition and the unique structure of the nanocomposites is considered to be a useful basis for future applications in functionalized degradable biomaterials.

STATEMENT OF SIGNIFICANCE

A novel bioinspired mineralization process was developed based on electric field-assisted migration of calcium and phosphate ions into biochemically carboxymethylated gelatin acting as organic template. Advantages over conventional hydroxyapatite include particle size distribution and homogeneity as well as achievable mechanical properties of relevant composites. Moreover, specifically developed calcium ion or phosphate ion release during degradation can be useful to adjust the fate of bone cells in order to manipulate remodeling processes. The hollow structure of the spheres can be useful for embedding drugs in the core, encapsulated by the highly mineralized outer shell. In this way, controlled drug release could be achieved, which enables advanced strategies for threating bone-related diseases, e.g. osteoporosis and multiple myeloma.

A correlative spatiotemporal microscale study of calcium phosphate formation and transformation within an alginate hydrogel matrix

The modification of soft hydrogels with hard inorganic components is a method used to form composite materials with application in non-load-bearing bone tissue engineering. The inclusion of an inorganic component may provide mechanical enhancement, introduce osteoconductive or osteoinductive properties, or change other aspects of interactions between native or implanted cells and the material. A thorough understanding of the interactions between such components is needed to improve the rational design of such biomaterials. To achieve this goal, model systems which could allow study of the formation and transformation of mineral phases within a hydrogel network with a range of experimental methods and high spatial and time resolution are needed. Here, we report a detailed investigation of the formation and transformation process of calcium phosphate mineral within an alginate hydrogel matrix. A combination of optical microscopy, confocal Raman microspectroscopy and electron microscopy was used to investigate the spatial distribution, morphology and crystal phase of the calcium phosphate mineral, as well as to study transformation of the mineral phases during the hydrogel mineralization process and upon incubation in a simulated body fluid. It was found, that under the conditions used in this work, mineral initially formed as a metastable amorphous calcium phosphate phase (ACP). The ACP particles had a distinctive spherical morphology and transformed within minutes into brushite in the presence of brushite seed crystals or into octacalcium phosphate, when no seeds were present in the hydrogel matrix. Incubation of brushite-alginate composites in simulated body fluid resulted in formation of hydroxyapatite. The characterization strategy presented here allows for non-destructive, in situ observation of mineralization processes in optically transparent hydrogels with little to no sample preparation.

STATEMENT OF SIGNIFICANCE

The precipitation and transformations of calcium phosphates (CaP) is a complex process, where both formation kinetics and the stability of different mineral phases control the outcome. This situation is even more complex if CaP is precipitated in a hydrogel matrix, where one can expect the organic matrix to modulate crystallization by introducing supersaturation gradients or changing the nucleation and growth kinetics of crystals. In this study we apply a range of characterization techniques to study the mineral formation and transformations of CaP within an alginate matrix with spatiotemporal resolution. It demonstrates how a detailed investigation of the mineral precipitation and transformations can aid in the future rational design of hydrogel-based materials for bone tissue engineering and studies of biomineralization processes.

Strong and Biostable Hyaluronic Acid-Calcium Phosphate Nanocomposite Hydrogel via in Situ Precipitation Process

Hyaluronic acid (HAc) hydrogel exhibits excellent biocompatibility, but it has limited biomedical application due to its poor biomechanical properties as well as too-fast enzymatic degradation. In this study, we have developed an in situ precipitation process for the fabrication of a HAc-calcium phosphate nanocomposite hydrogel, after the formation of the glycidyl methacrylate-conjugated HAc (GMHA) hydrogels via photo-cross-linking, to improve the mechanical and biological properties under physiological conditions. In particular, our process facilitates the rapid incorporation of calcium phosphate (CaP) nanoparticles of uniform size and with minimal agglomeration into a polymer matrix, homogeneously. Compared with pure HAc, the nanocomposite hydrogels exhibit improved mechanical behavior. Specifically, the shear modulus is improved by a factor of 4. The biostability of the nanocomposite hydrogel was also significantly improved compared with that of pure HAc hydrogels under both in vitro and in vivo conditions.

Tough dual nanocomposite hydrogels with inorganic hybrid crosslinking

A dual nanocomposite hydrogel with inorganic hybrid crosslinking was fabricated through a simultaneous sol-gel technique and free radical polymerization. Due to the multi-strengthening mechanism of the dual nanocomposite, the hydrogel was super tough and strong with a compressive stress of 32.00 MPa without rupture even at 100% strain, while it exhibited excellent fatigue resistant properties.

A novel biocompatible double network hydrogel consisting of konjac glucomannan with high mechanical strength and ability to be freely shaped

A novel physically linked double-network (DN) hydrogel was prepared by natural polymer KGM and synthetic polymer PAAm. The DN hydrogels exhibit good mechanical properties, cell adhesion properties, and can be freely shaped, making such hydrogels promising for tissue engineering scaffolds.

Highly stretchable and super tough nanocomposite physical hydrogels facilitated by the coupling of intermolecular hydrogen bonds and analogous chemical crosslinking of nanoparticles

Nanocomposite physical hydrogels fabricated by a one-step polymerization show ultra-extensibility and toughness due to an effective strengthening mechanism.

Electric field-induced gradient strength in nanocomposite hydrogel through gradient crosslinking of clay

Nanocomposite gradient hydrogels with adjustable mechanical strength and network sizes were synthesized by electric field-induced gradient crosslinking polymerization.

Bioactive nanoparticle-gelatin composite scaffold with mechanical performance comparable to cancellous bones

Mechanical properties are among the most concerned issues for artificial bone grafting materials. The scaffolds used for bone grafts are either too brittle (glass) or too weak (polymer), and therefore composite scaffolds are naturally expected as the solution. However, despite the intensive studies on composite bone grafting materials, there still lacks a material that could be matched to the natural cancellous bones. In this study, nanosized bioactive particles (BP) with controllable size and good colloidal stability were used to composite with gelatin, forming macroporous scaffolds. It was found that the mechanical properties of obtained composite scaffolds, in terms of elastic modulus, compressive strength, and strain at failure, could match to that of natural cancellous bones. This is ascribed to the good distribution of particle in matrix and strong interaction between particle and gelatin. Furthermore, the incorporation of BPs endues the composite scaffolds with bioactivity, forming HA upon reacting with simulated body fluid (SBF) within days, thus stimulating preosteoblasts attachment, growth, and proliferation in these scaffolds. Together with their good mechanical properties, these composite scaffolds are promising artificial bone grating materials.

In situ osteoblast mineralization mediates post-injection mechanical properties of osteoconductive material

The objective of this study was to understand the temporal relationship between in situ generated calcium content (mineralization) and the mechanical properties of an injectable orthobiologic bone-filler material. Murine derived osteoblast progenitor cells were differentiated using osteogenic factors and encapsulated within an injectable polycaprolactone nanofiber-collagen composite scaffold (PN-COL +osteo) to evaluate the effect of mineralization on the mechanical properties of the PN-COL scaffold. A comprehensive study was conducted using both an experimental and a predictive analytical mechanical analysis for mechanical property assessment as well as an extensive in vitro biological analysis for in situ mineralization. Cell proliferation was evaluated using a PicoGreen dsDNA quantification assay and in situ mineralization was analyzed using both an alkaline phosphatase (ALP) assay and an Alizarin Red stain-based assay. Mineralized matrix formation was further evaluated using energy dispersive x-ray spectroscopy (EDS) and visualized using SEM and histological analyses. Compressive mechanical properties of the PN-COL scaffolds were determined using a confined compression stress-relaxation protocol and the obtained data was fit to the standard linear solid viscoelastic material mathematical model to demonstrate a relationship between increased in situ mineralization and the mechanical properties of the PN-COL scaffold. Cell proliferation was constant over the 21 day period. ALP activity and calcium concentration significantly increased at day 14 and 21 as compared to PN-COL -osteo with undifferentiated osteoblast progenitor cells. Furthermore, at day 21 EDS, SEM and von Kossa histological staining confirmed mineralized matrix formation within the PN-COL scaffolds. After 21 days, compressive modulus, peak stress, and equilibrium stress demonstrate significant increases of 3.4-fold, 3.3-fold, and 4.0-fold respectively due to in situ mineralization. Viscoelastic parameters calculated through the standard linear solid mathematical model fit to the stress-relaxation data also indicate improved mechanical properties after in situ mineralization. This investigation clearly demonstrates that in situ mineralization can increase the mechanical properties of an injectable orthobiologic scaffold and can possibly guide the design of an effective osteoconductive injectable material.

Multi-scale multi-mechanism design of tough hydrogels: building dissipation into stretchy networks

As swollen polymer networks in water, hydrogels are usually brittle. However, hydrogels with high toughness play critical roles in many plant and animal tissues as well as in diverse engineering applications. Here we review the intrinsic mechanisms of a wide variety of tough hydrogels developed over the past few decades. We show that tough hydrogels generally possess mechanisms to dissipate substantial mechanical energy but still maintain high elasticity under deformation. The integrations and interactions of different mechanisms for dissipating energy and maintaining elasticity are essential to the design of tough hydrogels. A matrix that combines various mechanisms is constructed for the first time to guide the design of next-generation tough hydrogels. We further highlight that a particularly promising strategy for the design is to implement multiple mechanisms across multiple length scales into nano-, micro-, meso-, and macro-structures of hydrogels.

Hollow hydroxyapatite spheres fabrication with three-dimensional hydrogel template

Flower-like porous hollow HAp spheres were obtained by diffusion of phosphate ions into PAAm hydrogels containing calcium ions by both an electrophoresis approach and an ion diffusion method.