Fluorinated Benzothiadiazole-Based Polymers for Organic Solar Cells: Progress and Prospects

The integration of fluorinated benzothiadiazole (FBT) into donor-acceptor (D-A) copolymers represents a major advancement in the field of organic solar cells (OSCs). The fluorination process effectively fine-tunes the energy levels, reduces the highest occupied molecular orbital levels, and enhances the open-circuit voltages of the polymers. Furthermore, fluorination improves molecular packing and crystallinity, which significantly boosts the charge transport and overall device performance. This review provides a detailed analysis of the progress made with FBT-based polymers in OSCs, classifying these materials according to their copolymerization units. It discusses the design strategies and structure-property relationships that have emerged as well as the current challenges and future directions for optimizing these polymers. By offering a comprehensive overview of the existing research, this review aims to facilitate the development of high-performance FBT-based organic photovoltaic materials, ultimately contributing to the advancement of sustainable energy solutions.

A rational design of polymers through donor modulation to weaken the aggregation-caused quenching effect for NIR-II fluorescence imaging

The great tissue penetration depth and low tissue autofluorescence of NIR-II fluorescence imaging make it attractive for in vivo diagnosis. However, the aggregation-caused quenching (ACQ) effect is among the dominant obstacles that weaken NIR-II imaging and restrict its application. Herein, the donor unit, 2,8-dibromo-6H,12H-5,11-methanodibenzo[b,f] [1,5]diazocine with a V-configuration, was introduced to prepare the donor-acceptor (D-A) polymer P-TB with a twisted backbone, while the planar D-A polymer P-TP was used as a control. P-TB and P-TP were prepared by Stille Coupling with DPP as the acceptor. The main absorption peaks of P-TB and P-TP are located at 610 nm and 640 nm, and the emission peaks of P-TB and P-TP are 1060 nm and 930 nm, respectively. Significantly, the V-shaped P-TB showed no obvious ACQ effect within 600 μM, and the same phenomenon was demonstrated during in vivo NIR-II imaging in mice, which proves that the introduction of V-configuration donor units is beneficial for weakening the ACQ effect. This work outlines a prospective tactic for the design of conventional NIR-II fluorescent polymers by modulating the configuration of the donor units.

Dithieno[3,2-b:2',3'-d]silole-based conjugated polymers for bioimaging in the short-wave infrared region

The short-wave infrared window (SWIR, 900–1700 nm) fluorescence imaging has been demonstrated to have excellent imaging performance in signal/noise ratio and tissue penetration compared to the conventional NIR biological window (NIR-I, 700–900 nm). Conventional organic SWIR fluorescent materials still suffer from low fluorescence quantum efficiency. In this work, a donor unit with sp³ hybrid configuration and an acceptor unit with small hindered alkyl side chains are employed to construct donor–acceptor (D–A) type conjugated polymers P1 and P2, which were substituted with one or two fluorine atoms. These structural features can alleviate the aggregation-caused quenching (ACQ) and contribute to charge transfer, resulting in a significantly improved fluorescence quantum efficiency. The SWIR fluorescent quantum efficiencies of P1 and P2 nanoparticles are 3.4% and 4.4%, respectively, which are some of the highest for organic SWIR fluorophores reported so far. Excellent imaging quality has been demonstrated with P2 nanoparticles for SWIR imaging of the vascular system of nude mice. The results indicate that our design strategy of introducing sp³ hybrid configuration and small hindered alkyl side chains to fabricate conjugated polymers is efficient in improving the fluorescent quantum efficiency as SWIR fluorescent imaging agents for potential clinical practice.

A D–A type polymer with a SWIR fluorescence quantum efficiency of 4.4% was obtained after structural optimization.

Incorporating a vertical BDT unit in conjugated polymers for drastically improving the open-circuit voltage of polymer solar cells

High open circuit voltages (V_ocs) of over 1.0 V were obtained for solar cell devices based on vertical BDT-containing conjugated polymers.

Medium bandgap copolymers based on carbazole and quinoxaline exceeding 1.0 V open-circuit voltages

Given the desire for superior VOC values in PSCs, we have designed and synthesized a series of ‘medium bandgap’ donor–acceptor (D–A) copolymers containing carbazole (Cz) and quinoxaline (Qx) (PCzDT-Qx, PCzDT-fQx, and PCzDT-ffQx).

Low bandgap copolymers based on monofluorinated isoindigo towards efficient polymer solar cells

Low bandgap copolymers based on fluorinated isoindigo afford 5.0% efficiency in polymer solar cells.

Cyclopentadithiophene–benzothiadiazole copolymers with permutations of repeating unit length and ratios; synthesis, optical and electrochemical properties and photovoltaic characteristics

Conjugated copolymers with varying ratios and lengths of cyclopentadithiophene to benzothiadiazole repeating units have been synthesized and characterised.

Nanoscale phase separation control in rationally designed conjugated polymer solar cells processed using co-additives

A conjugated polymer based on benzo[1,2-b:4,5-b′]dithiophene with a thiophene-conjugated side chain andN-alkylthieno[3,4-c]pyrrole-4,6-dione was synthesized.

Dithieno[3,2-b:2′,3′-d]silole-based low band gap polymers: the effect of fluorine and side chain substituents on photovoltaic performance

The effect of the F atom and the side-chain of dithieno[3,2-b:2′,3′-d]silole-based polymers on the optical, carrier mobility and photovoltaic properties was investigated.