Interfacial engineering of a multijunctional In2O3/WO3@Ti4N3Tx S-scheme photocatalyst with enhanced photoelectrochemical properties

Achieving high photoelectrochemical conversion efficiency requires the logical layout of a composite photocatalyst with optimal charge separation and transfer with ideal light harvesting capabilities to enhance the photocatalytic performance and the degradation rate towards organic pollutants. Herein, a novel In2O3/WO3@Ti4N3Tx S-scheme heterojunction was successfully synthesized and confirmed through valence band VB-XPS and Mott Schottky combined analysis. The formed MXene-doped In2O3/WO3@Ti4N3Tx S-scheme significantly enhances the charge flow and spatial separation with an improved oxidation and reduction ability. An in-built interfacial electric field at the WO3-In2O3 boundary enhanced the light-harvesting capacity, whereas Ti4N3Tx MXene offers a unique electron trapping effect which effectively lowers high charge carrier recombination rate-related photocatalytic deficit. It preserves the exceptional redox potency of the photocatalyst by providing a directed acceleration and effective separation of the photogenerated charges. A high carrier density (ND = 7.83 × 1021 cm-3) with a lower negative flat band (VFB = -0.064 V vs. Ag/AgCl) was obtained by Mott-Schottky analysis for 3 wt% In2O3/WO3@Ti4N3Tx, an indicator that a low overpotential is needed to activate photocatalytic reactions. This study, therefore, provides a novel thought for the design and fabrication of an S-scheme heterojunction for photocatalytic reactions for mineralization of organic pollutants in water and clean energy production.

Elucidating Structural Stability, Bandgap, and Photocatalytic Hydrogen Evolution of (H2O/DMF)@HKUST-1 Host-Guest Systems

The H2O@HKUST-1 and DMF@HKUST-1 systems were experimental and computationally assessed, employing XRD/TGA/FT-IR/DFT-calculations, evidencing that H2O or DMF coordinated to Cu, modulating HKUST-1 photocatalytic properties. DMF@HKUST-1 has narrower bandgap promoting higher-crystallinity and light-harvesting. H2O@HKUST-1 showed smaller particle sizing and sharp morphology. Theoretical models, (H2O)1@HKUST-1 and (DMF)1@HKUST-1, containing one coordinated molecule, elucidated bandgap modulation associated with infiltration. H2O@HKUST-1/DMF@HKUST-1 presented bandgaps [eV] of 3.6/3.4, by Tauc plots, and 3.55/3.26, by theoretical calculations, narrowing bandgap, compared with non-solvated HKUST-1(HKUST-1NS). Both composites raised the valence band (VB) and lowered the conduction band (CB), but DMF@HKUST-1 most raised VB. Topological analysis revealed that guests i) with higher electronic density, raised VB, and ii) induced π-backbonding, lowering CB. DMF@HKUST-1 presented a higher photocatalytic hydrogen evolution (μmol), 26.45, in the first 30 min of the reaction, nevertheless, H2O@HKUST-1 presented a competitive activity, of 17.32. In large periods, H2O@HKUST-1/DMF@HKUST-1 showed practically the same hydrogen evolution, 45.50/49.03.

Design and Characterization of Zeolite/Serpentine Nanocomposite Photocatalyst for Solar Hydrogen Generation

In this work, a low-cost, high-yield hydrothermal treatment was used to produce nanozeolite (Zeo), nanoserpentine (Serp), and Zeo/Serp nanocomposites with weight ratios of 1:1 and 2:1. At 250 °C for six hours, the hydrothermal treatment was conducted. Various methods are used to explore the morphologies, structures, compositions, and optical characteristics of the generated nanostructures. The morphological study revealed structures made of nanofibers, nanorods, and hybrid nanofibril/nanorods. The structural study showed clinoptilolite monoclinic zeolite and antigorite monoclinic serpentine with traces of talcum mineral and carbonates. As a novel photoelectrochemical catalyst, the performance of the Zeo/Serp (2:1) composite was evaluated for solar hydrogen generation from water splitting relative to its constituents. At -1 V, the Zeo/Serp (2:1) composite produced a maximum current density of 8.44 mA/g versus 7.01, 6.74, and 6.6 mA/g for hydrothermally treated Zeo/Serp (1:1), Zeo, and Serp, respectively. The Zeo/Serp (2:1) photocatalysts had a solar-to-hydrogen conversion efficiency (STH) of 6.5% and an estimated hydrogen output rate of 14.43 mmole/h.g. Consequently, the current research paved the way for low-cost photoelectrochemical catalytic material for efficient solar hydrogen production by water splitting.

Impact of Erbium (Er) and Yttrium (Y) doping on BiVO4 crystal structure towards the enhancement of photoelectrochemical water splitting and photocatalytic performance

An efficient BiVO₄nanocatalyst with Erbium (Er) and Yttrium (Y) doping was synthesized via a facile microwave irradiation route and the obtained materials were further characterized through various techniques such as p-XRD, FT-IR, FE-SEM, HR-TEM, UV-Vis DRS, PL, LSV, and EISanalysis. The obtained results revealed that the rare metals induce the stabilization of the monoclinic-tetragonal crystalline structure with a distinct morphology. The yttrium doped BiVO₄ (Y-BiVO₄) monoclinic-tetragonal exhibited anefficient photoelectrochemical water splitting and photocatalytic performanceare compared to bare BiVO₄. TheY-BiVO₄ indicated increased results of photocurrent of 0.43 mA/cm²and bare BiVO₄0.24 mA/cm². Also, the Y-doped BiVO₄ nanocatalyst showed the maximum photocatalytic activity for the degradation of MB, MO, and RhB. A maximum degradation of 93%, 85%, and 91% was achieved for MB, MO, and RhB respectively, within 180 min under the visible light illumination. The photocatalytic decomposition of acetaldehyde also was performed. The improved photoelectrochemical water splitting and photocatalytic activity are due to the narrowing the bandgap, leading to extending the photoabsorption capability and reducing the recombination rate of photoexcited electron-hole pairs through the formation inner energy state of the rare earth metals. The current study disclosed that the synthesis of nanomaterials with crystal modification could be a prospectivecontender forhydrogen energy production as well as to the photocatalytic degradation of organic pollutants.To the best of our knowledge, both photocatalytic and photoelectrochemical studies were never been reported before for this type of material.

Coal Fly Ash Decorated with Graphene Oxide-Tungsten Oxide Nanocomposite for Rapid Removal of Pb2+ Ions and Reuse of Spent Adsorbent for Photocatalytic Degradation of Acetaminophen

Coal fly ash was decorated with a graphene oxide-tungsten oxide nanorods nanocomposite (CFA/GO/WO3NRs nanocomposite) via a hydrothermal method and applied for the remediation of lead (Pb2+ ions). The Pb2+ ion-loaded spent adsorbent (CFA/GO/WO3NRs + Pb2+ nanocomposite) was reused for the photodegradation of acetaminophen. CFA/GO/WO3NRs + Pb2+ nanocomposite displayed rapid removal of Pb2+ ions. Pseudo-second-order kinetics and the Langmuir isotherm model described the adsorption data. The adsorption capacity of the CFA/GO/WO3NRs nanocomposite was 41.51 mg/g for the removal of Pb2+ ions. Additionally, the Pb2+ ion-loaded spent adsorbent significantly influenced the degradation of acetaminophen by photocatalysis where 93% degradation was observed. It is worthy to note the reuse application of Pb2+ ion-loaded spent adsorbent as a photocatalyst, which will significantly reduce the secondary waste obtained from conventional adsorption methods.

Synthesis, characterization and photocatalytic activity evaluation of WO3, TiO2 and WO3/TiO2 supported on zeolite faujasite

The present investigation is focused on the preparation, characterization, and photocatalytic activity evaluation of TiO2/zeolite, WO3/zeolite, WO3/TiO2/zeolite, and WO3/TiO2 composites. Zeolite fujasite (FAU) was synthesized by the hydrothermal method, while the semiconductor/zeolite composites by a straightforward physical mixture and calcination treatment. The photocatalytic activity of the materials was evaluated through the methyl orange (MO) degradation under near-UV irradiation (365 nm). The photocatalysts were characterized by X-ray diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscope (SEM), Energy-dispersive X-ray Spectroscopy (EDX), UV–vis diffuse reflectance spectroscopy and nitrogen physisorption. Results indicated that TiO2, WO3, and Zeolite Y kept their crystalline phases after the preparation method. TiO2 and WO3 particles were distributed on zeolite surface. Also, no significant changes in the band gap energies of the photocatalysts were found. The surface area of zeolite FAU decreased with the addition of TiO2 and WO3. The best MO degradation under near-UV irradiation was obtained with WO3/TiO2 heterojunction and TiO2 P25, no synergistic effect was found between semiconductors and zeolite FAU. Additionally, the kinetic data of the photocatalytic elimination of MO with all photocatalysts under near-UV radiation was investigated with several models: Zero-order, First-Order, Second Order, Modified Freundlich and Parabolic Diffusion, they were consistent with Modified Freundlich model. The effect of initial pH and photocatalyst weight was explored for TiO2/Zeolite composite and it was found that the best MO degradation was obtained at natural pH of 10.3 and 0.2 g of composite was the optimal amount of photocatalyst. Finally, the positive hole formation in all photocatalysts was detected by UV–vis spectroscopy and it was discovered that the highest density of positive holes was obtained with TiO2/zeolite composite.

Mesoporous Molybdenum-Tungsten Mixed Metal Oxide: A Solid Acid Catalyst for Green, Highly Efficient sp3-sp2 C-C Coupling Reactions

A mesoporous molybdenum tungsten mixed metal oxide with high surface area (173 m²/g) was synthesized by using metal dissolution coupled with a surfactant assisted reverse micelle formation synthesis method. Comprehensive characterization of the mixed oxide was performed by using PXRD, Raman, BET, SEM, EDX, TEM, and XPS. Thus, the formation of α-Mo_0.5W_0.5O₃ with a homogeneous distribution of Mo and W throughout the material was seen. Furthermore, multiple oxidation states of molybdenum (Mo⁶⁺ and Mo⁵⁺) and a single oxidation state of tungsten (W⁶⁺) were observed. The weak/moderate acidic sites present in the mixed metal oxide resulted in excellent catalytic properties toward the sp³-sp² carbon-carbon coupling reactions. The coupling of benzyl alcohol and toluene was completed within 15 min at 110 °C with 99% yield.

Experimental and DFT Studies of Au Deposition Over WO3/g-C3N4 Z-Scheme Heterojunction

A typical Z-scheme system is composed of two photocatalysts which generate two sets of charge carriers and split water into H₂ and O₂ at different locations. Scientists are struggling to enhance the efficiencies of these systems by maximizing their light absorption, engineering more stable redox couples, and discovering new O₂ and H₂ evolutions co-catalysts. In this work, Au decorated WO₃/g-C₃N₄ Z-scheme nanocomposites are fabricated via wet-chemical and photo-deposition methods. The nanocomposites are utilized in photocatalysis for H₂ production and 2,4-dichlorophenol (2,4-DCP) degradation. It is investigated that the optimized 4Au/6% WO₃/CN nanocomposite is highly efficient for production of 69.9 and 307.3 µmol h^-1 g^-1 H₂ gas, respectively, under visible-light (λ > 420 nm) and UV-visible illumination. Further, the fabricated 4Au/6% WO₃/CN nanocomposite is significant (i.e., 100% degradation in 2 h) for 2,4-DCP degradation under visible light and highly stable in photocatalysis. A significant 4.17% quantum efficiency is recorded for H₂ production at wavelength 420 nm. This enhanced performance is attributed to the improved charge separation and the surface plasmon resonance effect of Au nanoparticles. Solid-state density functional theory simulations are performed to countercheck and validate our experimental data. Positive surface formation energy, high charge transfer, and strong non-bonding interaction via electrostatic forces confirm the stability of 4Au/6% WO₃/CN interface.

Construction of coated Z-scheme Pd-BaZrO3@WO3 composite with enhanced sonocatalytic activity for diazinon degradation in aqueous solution

The coated Z-scheme Pd-BaZrO₃@WO₃ composite as a new-type sonocatalyst with highly sonocatalytic performance is first constructed through sol-gel and hydro-thermal synthesis methods. The chemical configuration, structure and component are characterized by a series of characterization methods. The sonocatalytic degradation of diazinon as a model pollutant is studied to estimate the sonocatalytic performance of coated Z-scheme Pd-BaZrO₃@WO₃ composite. Some affecting factors such as Pd-BaZrO₃ and WO₃ mass proportions, ultrasonic (US) irradiation time, reusability and catalyst dosage are researched in detail through UV-vis spectra and gas chromatography (GC). The produced intermediates are detected in the degradation process of diazinon by using gas chromatography-mass spectrometer (GC-MS). The possible reaction mechanism of coated Z-scheme Pd-BaZrO₃@WO₃ sonocatalyst in sonocatalytic degradation process is also explored. Subsequently, the hydroxyl radicals (OH) and holes (h⁺) are discriminated to further elaborate the possible sonocatalytic mechanism. The experimental results manifest that the coated Z-scheme Pd-BaZrO₃@WO₃ sonocatalyst displays a preeminent sonocatalytic performance under ultrasonic irradiation because it can efficaciously suppress recombination of electrons (e^-) and holes (h⁺), extend light response scope and provide almost 100% oxidization surface. In addition, the introduced palladium (Pd) nanorods connecting BaZrO₃ and WO₃ can expedite e^- transfer. Under optimal conditions, the most of diazinon molecules can be disintegrated in the existence of the coated Z-scheme Pd-BaZrO₃@WO₃ under ultrasonic irradiation for 150 min. This study provides a feasible method for the treatment of environmental pollutions.

Influence of cobalt substitution on the crystal structure, band edges and photocatalytic properties of hierarchical Bi2WO6 microspheres

An efficient Bi₂WO₆ catalyst with Co²⁺ substitution was synthesized via a facile hydrothermal route.

Investigation of the structural, optical and crystallographic properties of Bi2WO6/Ag plasmonic hybrids and their photocatalytic and electron transfer characteristics

We have fabricated an efficient Bi₂WO₆-Ag plasmonic hybrid via the photoreduction technique and the obtained materials were well characterized with sophisticated instruments.

Fabrication of RuO2-Ag3PO4 heterostructure nanocomposites: Investigations of band alignment on the enhanced visible light photocatalytic activity

The RuO₂-Ag₃PO₄ heterostructured nanocomposite was successfully synthesized by facile in situ deposition of porous ruthenium oxide (RuO₂) nanoparticles on the surface of the silver phosphate (Ag₃PO₄). Under visible light irradiation, the 0.5wt.% RuO₂-Ag₃PO₄ heterostructure photocatalyst exhibits enhanced photocatalytic efficiency compared to other composites of RuO₂-Ag₃PO₄ and Ag₃PO₄. The optimized 0.5wt.% RuO₂-Ag₃PO₄ nanocomposites exhibited 1.5 times enhanced photocatalytic activity towards the degradation of methylene blue (MB) than Ag₃PO₄. Moreover, the degradation rate of 0.5wt.% RuO₂-Ag₃PO₄ nanocomposite towards the cationic dyes MB and rhodamine B (RhB) was nearly 6.6 times and 4.7 times higher than that towards the anionic dye methyl orange (MO). The formed heterojunction electric field of 310mV at the interface between RuO₂ and Ag₃PO₄ heterostructure induces downward band bending of Ag₃PO₄. Also, this electric field increases the separation efficiency of electrons-holes resulting higher degradation efficiency. The quenching effect of scavengers test confirms that holes are reactive species and the RuO₂-Ag₃PO₄ nanocomposite is highly stable, exhibited 88% of MB degradation after 4 recycles. The RuO₂-Ag₃PO₄ nanocomposites inhibit self oxidation of Ag₃PO₄ resulting improved efficiency and stability.

Recent advances in photocatalytic treatment of pollutants in aqueous media

Photocatalysis can be an excellent solution for resolving the world's energy and environmental problems. It has a wide range of applications for the decontamination of diverse hazardous pollutants in aqueous media. Technological progress in this research field has been achieved toward the improvement of the solar sensitivity to enhance the efficiency of pollutant decontamination. As a result, various strategies have been introduced to upgrade photocatalytic performance with the modification of prototypical photocatalyst such as doping, dye sensitization, semiconductor coupling, mesoporous supports, single site, and nano-based catalysts. In this review, a brief survey is presented to describe those strategies based on the evaluation made against various pollutants (such as pharmaceuticals, pesticides, heavy metals, detergents, and dyes) in aqueous media.

The effect of cerium alteration on the photocatalytic performance of WO3 in sunlight exposure for water decontamination

In an effort to enhance the photocatalytic activity of cubic WO₃ in sunlight exposure, its surface was modified by impregnating the Ce³⁺ ions ranging from 1% to 25% with a step of 5% with respect to the weight of WO₃.

Three way electron transfer of a C–N–S tri doped two-phase junction of TiO2nanoparticles for efficient visible light photocatalytic dye degradation

C–N–S tridoped TiO₂nanoparticles were synthesized by a sol–gel method using thiourea as a compound source of carbon (C), nitrogen (N) and sulphur (S).

Combined experimental and theoretical investigations on the encapsulation of nickel(ii)tet-a complex in zeolite Y and its photocatalytic activity

Photocatalytic mechanism of the 5,7,7,12,14,14-hexamethyl-1,4,8,11-tetraazacyclotetradecane [tet-a] nickel(ii) encapsulated in zeolite Y.

Light-induced spatial separation of charges toward different crystal facets of square-like WO3

Light-induced preferential migration of electrons and holes to the minor (200) and (020) facets and the dominant (002) facets of square-like WO₃, respectively, resulted in the square-like WO₃ nanoplates with Pt loaded mainly on dominant (002) facets shows higher photocatalytic activity than that Pt loaded on the minor facets.

Crystallographic dependence of photocatalytic activity of WO3thin films prepared by molecular beam epitaxy

The (111) surface of WO₃is found to have the highest photocatalytic reactivity, followed by (110) and (001).

Green synthesis of ZnO hollow sphere nanostructures by a facile route at room temperature with efficient photocatalytic dye degradation properties

The present work has prepared ZnO hollow spherical nanoparticles using a straightforward synthetic route and has innovatively made use of carbon spheres as a template at room temperature.

Tuning the electronic and structural properties of WO3 nanocrystals by varying transition metal tungstate precursors

WO₃ nanoplates derived from NiWO₄ were found to have the highest concentration of oxygen vacancy, narrowest band gap, longest electron–hole recombination time, and in turn the highest rate of photodegradation of azo dye methylene blue.