Polyaniline-Based Cationic Porous Organic Polymers for Fast and Efficient Anion-Exchange-Driven Capture of Cr2O7 2

Efficient treatment of wastewater contaminated with carcinogenic Cr(VI) has been a long-term challenge for both academic and industrial research efforts. Removal of Cr(VI) species by ion exchange is a relatively simple and efficient method, and its combination with highly tailorable nanomaterials is promising for the treatment of such wastewater. Here, we report a type of cationic porous organic polymer (POP), namely, PTPA-PIP, which can be prepared simply by converting the corresponding aromatic polyamine PTPA to its protonated form, thereby significantly increasing its hydrophilicity and ability to disperse homogeneously in water, crucial for application in water treatment. In addition to detailed characterization of the physicochemical properties of PTPA-PIP (including using Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS), Brunauer-Emmett-Teller (BET), and solid-state NMR techniques), adsorption experiments demonstrate that PTPA-PIP removes low-concentration dichromate anions with very high performance, including excellent exchange capacity (maximum capacity of 230 mg Cr2O7 2-/g PTPA-PIP), ultrafast removal (initial adsorption rate of 83 mg g-1 min-1), excellent selectivity (∼10% loss of adsorption capacity in the presence of 40-fold concentration of competing anions), as well as superior reusability (reusable for at least 5 cycles without compromised performance). These results demonstrate that PTPA-PIP is an outstanding candidate for application in industrial settings for the effective removal of harmful Cr(VI) pollutants in wastewater.

Fruit waste-derived cellulose-polyaniline composite for adsorption-coupled reduction of chromium oxyanions

Hexavalent chromium oxyanions, known as potentially toxic micropollutants, exist in the effluents and discharges of metallurgical, electroplating, refractory, chemical, and tanning industries. The exposure of chromium-contaminated water causes severe health hazards. The present work outlines a facile approach to grow polyaniline (PANI) on fruit-waste-derived cellulose (CEL) via oxidative polymerization of aniline; followed by chemical processing with NH4OH to obtain CEL-PANI-EB composites for adsorptive separation-coupled reduction of highly toxic hexavalent chromium oxyanions. The spectroscopic analyses of the CEL-PANI-EB composite before and after adsorption of Cr(VI) oxyanions revealed hydrogen bonding, electrostatic, and complexation as major interactive pathways. The adsorbed hexavalent chromium oxyanions are reduced into Cr(III) species by oxidation of PANI-based benzenoid amine into quinoid imine in the CEL-PANI-EB composite. The adsorption of Cr(VI) oxyanions by the CEL-PANI-EB composite showed negligible effects of other anionic co-pollutants, like NO3- and SO42-. The CEL-PANI-EB composite adsorbed Cr(VI) oxyanions with a removal capacity of 469 mg g-1, based on the Langmuir adsorption isotherm model. The hydroxyl functionalities in cellulose and amine/imine functionalities in PANI facilitate the electrostatic attraction between the CEL-PANI-EB and Cr(VI) oxyanions in an acidic environment beside the hydrogen linkages. The adsorbed Cr(VI) oxyanions are reduced to Cr(III)-based species by the benzenoid amines of PANI, as revealed from the XPS analyses. The CEL-PANI-EB composite showed excellent recyclability and maintained 83.4% adsorption efficiency after seven runs of chromium adsorption-desorption. The current findings reveal the potential of CEL-PANI-EB composites for the adsorptive removal of Cr(VI) oxyanions and their conversion into a lesser toxic form, making them promising materials for wastewater treatment applications.

Tannic acid-assisted fabrication of antibacterial sodium alginate-based gel beads for the multifunctional adsorption of heavy metal ions and dyes

The existence of heavy metals and dyes seriously affects the ecological environment and human safety. Antibacterial adsorption materials with the broad-spectrum removal of multiple pollutants are urgently required for water remediation. Herein, a sustainable and antibacterial sodium alginate (SA) gel bead adsorbent with honeycomb cellular architecture is developed by the biomimetic deposition polyphenolic tannic acid (TA) induced grafting diethylenetriamine (DETA) under mild conditions for efficient removal of Cr(VI) and dyes. Taking advantage of the catechol surface chemistry, TA occurring rapid polymerization with DETA monomers not only enhances the water resistance and thermal stability of the gel bead, but also introduces abundant polyphenolic functional groups and active adsorption sites. The multifunctional gel bead showed outstanding antibacterial activity against S. aureus (sterilization rates: 83.8 %) and E. coli (sterilization rates: 99.5 %). The maximum adsorption capacity of gel bead for Cr(VI) was 163.9 mg/g. Moreover, the removal efficiency of the gel bead for dyes of Safranine T and Rhodamine B was 89.5 % (maximum adsorption capacity: 537 mg/g) and 76.7 % (maximum adsorption capacity: 460.2 mg/g), respectively, indicating its excellent broad-spectrum adsorption performance for multiple pollutants. Therefore, TA-assisted fabrication of SA-based gel bead with excellent antibacterial property is a promising multifunctional adsorption material for practical water remediation.

One-Step Fabrication of Recyclable Konjac Glucomannan-Based Magnetic Nanoparticles for Highly Efficient Cr(VI) Adsorption

Recently, the natural polymer polysaccharide konjac glucomannan (KGM) has received attention as a promising adsorbent in water treatment due to its low toxicity, cost-effectiveness and biocompatibility. However, the high-level water absorbency of KGM makes it difficult to recover in water treatment. In this study, by combining KGM with magnetic nanoparticles, KGM-based magnetic nanoparticles (KGM-Fe3O4 NPs) with excellent adsorption properties and recyclability for heavy metals were prepared using an one-step precipitation method. The as-prepared KGM-Fe3O4 NPs have a spherical morphology of superparamagnetism with a small particle size (ca. 7.0 nm) and a large specific surface area (160.1 m2·g-1). Taking Cr(VI) as the target heavy metal ion, the above nanoparticles have a high adsorption capacity and fast adsorption rate for Cr(VI). The pseudo-second order kinetic model is more suitable to describe the adsorption process of Cr(VI) by KGM-Fe3O4 NPs, and the maximum adsorption capacity of Cr(VI) onto KGM-Fe3O4 NPs was calculated to be 41.67 mg·g-1 using the Langmuir isotherm model. In addition, KGM-Fe3O4 NPs with adsorbed heavy metal ions can be quickly recovered from a solution, regenerated, and reused in the next cycle. KGM-based Fe3O4 nanoparticles are promising adsorbents that show significant reusability for the removal of metal ions in water and wastewater treatment.

Mechanistic insights of hexavalent chromium remediation by halloysite-supported copper nanoclusters

Chromium (Cr) pollution is a significant environmental concern with remediation challenge. Hexavalent chromium (Cr(VI)) is more toxic than trivalent chromium (Cr(III)) due to its mutagenicity and oncogenicity. In this investigation, a multi-functional material, copper nanoclusters (CuNCs)-halloysite nanotubes (HNT) composite (CuNCs@HNT), has been synthesised in an eco-friendly manner and utilised for Cr(VI) remediation. Advanced analytical tools confirmed the seeding of ultra-fine CuNCs onto HNT surfaces. The maximum adsorption capacity of CuNCs@HNT is 79.14 ± 6.99 mg/g at pH 5 ± 0.1 with an increment at lower pHs. This performance was comparable for real surface stream water as well as other reported materials. The pseudo-second-order kinetic-, intra-particle diffusion- and Freundlich isotherm models well fit the experimental data implying that the chemisorption, multiphase diffusion and multi-molecular layer distribution occurred during adsorption. The Fourier-transform infrared and the x-ray photoelectron spectra also ensured the transformation of Cr(VI) to Cr(III) indicating the material's suitability for concurrent adsorption and reduction of Cr(VI). While coexisting cations and anions did not overwhelm this adsorption, CuNCs@HNT was regenerated and reused five successive times in adsorption-desorption cycles without significant loss of adsorption capacity and material's integrity. Therefore, this multi-functional, biocompatible, low-cost and stable CuNCs@HNT composite may have practical application for similar toxic metals remediation.

Investigating the selectivity and interference behavior for detoxification of Cr(VI) using lanthanum phosphate polyaniline nanocomposite via adsorption-reduction mechanism

A novel Lanthanum phosphate polyaniline (LaPO₄-PANI) nanocomposite was synthesized by the simple sol-gel technique. The nanocomposite prepared at 1:1 ratio provided the highest ion exchange capacity and selective adsorption of Cr(VI). The phase composition and particle morphology of the as-prepared material was evaluated by XRD, FESEM and TEM analyses. The FTIR, Raman, and TGA data inferred the definite chemical interaction between the organic and inorganic counterparts in the formation of LaPO₄-PANI. The selective adsorption of Cr(VI) was estimated by evaluating the distribution coefficient, electrical double layer theory as well as valency and Pauling's ionic radii of interfering ions (phosphate, iodide, sulfate, chloride, sulfide). The high tolerance capability of LaPO₄-PANI against the interfering ions made it appropriate for selective and efficient removal of Cr(VI) ions from solutions. The nanocomposite showed the highest removal percentage of 98.6% towards Cr(VI) in a wide pH range of 2-6 at room temperature, as compared to sole lanthanum phosphate (56%) and polyaniline (75%). The XPS analysis revealed the adsorption mechanism due to the combined effect of both adsorption and reduction. Cr(VI) is adsorbed through electrostatic interactions while the = N-/-NH- group facilitated the in situ chemical reduction. The procured results make the LaPO₄-PANI nanocomposite a promising adsorbent for the removal of Cr(VI).

Hydrothermal synthesis of hydroxyapatite-reduced graphene oxide (1D-2D) hybrids with enhanced selective adsorption properties for methyl orange and hexavalent chromium from aqueous solutions

The presence of organic dye molecules and heavy metal ions in water causes ecological and public health problems. Therefore, remediation of water/wastewater contaminated with organic dye molecules and toxic metal ions is of importance. Herein, a reduced graphene oxide (RGO)-hydroxyapatite (Hat) (1D-2D) hybrid composite was fabricated through a hydrothermal process and applied for the adsorption of methyl orange (MO) and hexavalent chromium (Cr(VI)) from water. The as-fabricated RGO-Hat hybrids were characterized using FTIR, XRD, HR-TEM, SEM, XPS, EDAX, and TGA-DSC analytical techniques. The influencing parameters of adsorption performance, namely solution pH, contact time, and co-interfering ions, were explored to obtain the maximum adsorption capacity of contaminants from the solid-liquid interface. Batch studies revealed that MO and Cr(VI) adsorption followed the pseudo-second-order kinetic and the Langmuir isotherm models. The adsorption capacity was 49.14 and 45.24 mg g^-1 for MO and Cr(VI), respectively. The adsorption of such ions over RGO-Hat hybrids was mainly driven by several uptake mechanisms viz, electrostatic force of attraction, π-π interactions, and hydrogen bonding. Thus, this study demonstrated that the RGO-Hat hybrid is a potential candidate for the treatment of MO and Cr(VI) from water.

DABCO Derived Nitrogen-Doped Carbon Nanotubes for Oxygen Reduction Reaction (ORR) and Removal of Hexavalent Chromium from Contaminated Water

Though chemically-derived reduced graphene oxide (CDG) from graphite oxide (GO) precursors is a widely practiced procedure for the large-scale production of graphene, the quality and quantity of thus obtained CDG is dependent on the reduction strategy used. In this work, we report an all-solid-state, residue-free, microwave process for the reduction of graphene oxide and subsequent growth of carbon nanotube ‘separators’ from a single precursor, namely DABCO (1,4-diazabicyclo[2.2.2]octane). The utility of our newly developed technique in efficiently and effectively reducing graphene oxide and in growing nitrogen-doped carbon nanotubes via catalysts like palladium and iron into unique mesoporous, 3-D hierarchical carbon nanostructures is demonstrated. The applicability of the thus obtained palladium embedded in Pd@NCNT-rGO nanoarchitectures for the oxygen reduction reaction (ORR) is investigated. When carbon fiber (CF) was used as the substrate, three-dimensional Fe@NCNT-CF were obtained, whose capability as versatile adsorbents for hexavalent chromium ion removal from contaminated waters was also demonstrated.

Synthesis of Polyaniline Coating on the Modified Fiber Ball and Application for Cr(VI) Removal

In this study, polyaniline (PANI) is prepared by means of chemical oxidization polymerization and directly loaded on the modified fiber ball (m-FB) to obtain macroscale polyaniline/modified fiber ball (PANI/m-FB) composite, and then its removal ability of Cr(VI) is investigated. The effects of different parameters such as contact time, pH value and initial concentration on Cr(VI) removal efficiency are discussed. The experimental results illustrate that the favorable pH value is 5.0 and the maximum removal capacity is measured to be 293.13 mg g^-1. Besides, PANI/m-FB composites can be regenerated and reused after being treated with strong acid. The kinetic study indicates that the adsorption procedure is mainly controlled by chemical adsorption. More importantly, the macroscale of composites can avoid secondary pollution efficiently. Benefiting from the low cost, easy preparation in large scale, environmentally friendly, excellent recycling performance as well as high removal ability, PANI/m-FB composites exhibit a potential possibility to remove Cr(VI) from industrial waste water. The polyaniline (PANI) was coated on modified fiber ball (m-FB) to remove Cr(VI) in waste water, and this kind of PANI/m-FB composites can avoid secondary pollution efficiently due to its macrostructure. Furthermore, the removal capacity can reach to 291.13 mg/g and can be multiple reused.

Significance of conducting polyaniline based composites for the removal of dyes and heavy metals from aqueous solution and wastewaters - A review

Dyes and heavy metals pollution have become a major environmental concern worldwide. Various methods, such as advanced oxidation, biodegradation, precipitation, flocculation, ultra filtration, ion-exchange, electro-chemical degradation and coagulation, have been proposed for the removal of dyes and heavy metals from contaminated wastewater. Of these methods, adsorption and detoxification are considered as the most promising and economically viable. Polyaniline-based composites, a material prepared by combining polyaniline with one or more similar or disimilar materials, have been reported as good adsorbents to remove and detoxify different groups of pollutants due to their unique physical and chemical properties. In the last decade, several studies have reported the effective adsorption (∼95%) of dyes and heavy metals onto polyaniline based composites. Furthermore, some polyaniline -composites reduced the adsorbed heavy metals into less toxic state. This review compiles the application of different polyaniline composites for adsorption and/or detoxifcation of dyes and heavy metals and documents composite preparation methods, morphology and properties of the composites, and mechanism of dyes and heavy metals adsorption. Based on the avilabile literature, this review suggests that more studies are warranted to understand the influence of various conditions and experimental variables on dyes and heavy metals removal from wastewater and/or aqueous solution.

A Review on Heavy Metal Ions and Containing Dyes Removal Through Graphene Oxide-Based Adsorption Strategies for Textile Wastewater Treatment

Textile wastewater heavy metal pollution has become a severe environmental problem worldwide. Metal ion inclusion in a dye molecule exhibits a bathochromic shift producing deeper but duller shades, which provides excellent colouration. The ejection of a massive volume of wastewater containing heavy metal ions such as Cr (VI), Pb (II), Cd (II) and Zn (II) and metal-containing dyes are an unavoidable consequence because the textile industry consumes large quantities of water and all these chemicals cannot be combined entirely with fibres during the dyeing process. These high concentrations of chemicals in effluents interfere with the natural water resources, cause severe toxicological implications on the environment with a dramatic impact on human health. This article reviewed the various metal-containing dye types and their heavy metal ions pollution from entryway to the wastewater, which then briefly explored the effects on human health and the environment. Graphene-based absorbers, specially graphene oxide (GO) benefits from an ordered structured, high specific surface area, and flexible surface functionalization options, which are indispensable to realize a high performance of heavy metal ion removal. These exceptional adsorption properties of graphene-based materials support a position of ubiquity in our everyday lives. The collective representation of the textile wastewater's effective remediation methods is discussed and focused on the GO-based adsorption methods. Understanding the critical impact regarding the GO-based materials established adsorption portfolio for heavy metal ions removal are also discussed. Various heavy-metal ions and their pollutant effect, ways to remove such heavy metal ions and role of graphene-based adsorbent including their demand, perspective, limitation, and relative scopes are discussed elaborately in the review.

Interlocked 3D active carbon fibers and monolithic I-doped Bi2O2CO3 structure built by 2D face-to-face interaction: endowed with cycling stability and photocatalytic activity

Photocatalysis is considered a remarkable green method in the catalytic degradation of wastewater; however, the collection and loading of the powdered catalyst is still a problem.

Key role of pore size in Cr(VI) removal by the composites of 3-dimentional mesoporous silica nanospheres wrapped with polyaniline

A series of three-dimensional silica nanospheres with different pore sizes was synthesized in a biphasic oil-water system and their pore dimensions were adjusted by controlling the composition of the oil phase. The silica nanospheres were then wrapped with polyaniline, characterized, and the obtained silica nanosphere-polyaniline composites were used for the removal of Cr(VI). Polyaniline was generated by the polymerization of aniline. The mesoporous silica has sufficient dendritic pore channels and offers a large contact surface for the polymerization of aniline. Furthermore, the mesoporous silica nanospheres are beneficial for dispersing polyaniline and transferring aqueous Cr(VI). The silica nanosphere-polyaniline composite with the largest pore size (~15.4 nm) showed the best Cr(VI) removal performance. We also investigated the kinetic characteristics and the result could be fitted to the pseudo-second-order kinetic model. Moreover, we demonstrate that the composites maintain a high Cr(VI) removal efficiency compared to other anions (H₂PO₄^-, SO₄^2-, etc.), indicating their good prospect in practical wastewater treatment. Remarkably, the silica-polyaniline composites showed enhanced Cr(VI) removal efficiency under UV-irradiation. The effects of electrons and H⁺ on Cr(VI) reduction are also discussed based on the results of UV-vis and X-ray photoelectron spectroscopic studies and bath experiments (influence of pH on adsorption capacity). Mechanistic studies indicate that the Cr(VI) removal occurs in two stages-adsorption and reduction. The negatively charged aqueous Cr(VI) species first interact with the positively charged protonated amine groups via electrostatic attraction, and are then further reduced to less-toxic Cr(III) by the electrons and H⁺ donated by the amine groups on polyaniline.

Simultaneous scavenging of Cr(VI) from soil and facilitation of nutrient uptake in plant using a mixture of carbon microfibers and nanofibers

Plant growth and yield are adversely affected by the uptake of toxic hexavalent chromium (Cr(VI)) from soil. The present study describes a facile technique to minimize the uptake of Cr(VI) by chickpea (Cicer arietinum) plant from soil using microporous activated carbon microfiber (ACF). Simultaneously, nano-sized carbon nanofibers (CNFs), grown over the ACF substrate, are used as an efficient carrier of the Cu micronutrient from soil to root, shoot and leaf of the plants. Adsorption, seed germination and plant growth experiments are performed in Cr-stressed medium. The ACF, used as the adsorbent for Cr(VI) in metal-stressed soil (100 mg Cr kg^-1 of soil) shows the metal loading of ∼23 mg g^-1. Cr(VI) up to 50 mg L^-1 concentration causes no stress during germination of chickpea seeds in Murashige and Skoog (MS) medium. A dose of 500 mg-mixture (treatment) per kg-soil increases root and shoot lengths by 52 and 11%, respectively than the control, during plant growth in the metal-stressed soil, attributed to an effective translocation of Cu-CNF through plant cells. Whereas Cr uptake by plant decrease to ∼46%, Cu uptake increase up to ∼120% in comparison to control by the mixture treatment. Protein and chlorophyll contents also significantly increased (*p < 0.05) with the application of treatment. The data clearly show that the mixture of ACF and Cu-CNF can be successfully used for the simultaneous scavenging of Cr(VI) from soil by adsorption over ACF and increased uptake of Cu by plants using the CNFs as the micronutrient carrier.

Enhanced adsorption-coupled reduction of hexavalent chromium by 2D poly(m-phenylenediamine)-functionalized reduction graphene oxide

To improve the mass transfer efficiency of poly(m-phenylenediamine) for the effective removal of hexavalent chromium (Cr (VI)) from aqueous solution, a facile and one-step method to prepare two-dimensional poly(m-phenylenediamine) functionalized reduction graphene oxide (rGO-PmPD) by dilution polymerization is developed. The structure and morphology of rGO-PmPD as well as rGO and PmPD were characterized by scanning electron microscope (SEM), transmission electron microscope (TEM), Brunauer-Emmett-Teller (BET), Fourier-transformed infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), Raman, and X-ray diffraction (XRD). The preparation mechanism, adsorption performance, and mechanism of rGO-PmPD were then investigated in detail. The obtained rGO-PmPD exhibited thin 2D nanosheet morphology with much improved specific surface area and pore volume (18 and 25 times higher than that of PmPD, respectively). The Cr (VI) adsorption of rGO-PmPD was fitted well with the pseudo-second-order kinetic model and Langmuir isotherm model, and the maximum adsorption capacity of rGO-PmPD reached 588.26 mg g^-1, higher than that of PmPD (400 mg g^-1) and rGO (156.25 mg g^-1). Moreover, the regeneration efficiency of the rGO-PmPD nanosheet is also promising that the adsorption performance after five times of adsorption-desorption cycles still maintains more than 530 mg g^-1. The removal mechanism involved reduction coupled with adsorption and electrostatic interaction between rGO-PmPD and Cr (VI), and ~ 65% of Cr (VI) removal was attributed to reduction and ~ 35% was ascribed to adsorption and electrostatic interaction. This study thus provides a simple and effective route to achieve high accessible surface area of adsorbent materials with enhanced mass transfer efficiency and thereafter improved adsorption performance.

Artificial Neural Networks (ANNs) and Response Surface Methodology (RSM) Approach for Modelling the Optimization of Chromium (VI) Reduction by Newly Isolated Acinetobacter radioresistens Strain NS-MIE from Agricultural Soil

Numerous technologies and approaches have been used in the past few decades to remove hexavalent chromium (Cr[VI]) in wastewater and the environment. However, these conventional technologies are not economical and efficient in removing Cr(VI) at a very low concentration (1-100 ppm). As an alternative, the utilization of bioremediation techniques which uses the potential of microorganisms could represent an effective technique for the detoxification of Cr(VI). In this study, we reported a newly isolated bacterium identified as Acinetobacter radioresistens sp. NS-MIE from Malaysian agricultural soil. The chromate reduction potential of strain NS-MIE was optimized using RSM and ANN techniques. The optimum condition predicted by RSM for the bacterium to reduce hexavalent chromium occurred at pH 6, 10 g/L ppm of nutrient broth (NB) concentration and 100 ppm of chromate concentration while the optimum condition predicted by ANN is at pH 6 and 10 g/L of NB concentration and of 60 ppm of chromate concentration with chromate reduction (%) of 75.13 % and 96.27 %, respectively. The analysis by the ANN model shows better prediction data with a higher R² value of 0.9991 and smaller average absolute deviation (AAD) and root mean square error (RMSE) of 0.33 % and 0.302 %, respectively. Validation analysis showed the predicted values by RSM and ANN were close to the validation values, whereas the ANN showed the lowest deviation, 2.57%, compared to the RSM. This finding suggests that the ANN showed a better prediction and fitting ability compared to the RSM for the nonlinear regression analysis. Based on this study, A. radioresistens sp. NS-MIE exhibits strong potential characteristics as a candidate for the bioremediation of hexavalent chromium in the environment.

SC, Chidangil S, George SD. Post annealing induced manipulation of phase and upconversion luminescence of Cr3+ doped NaYF4:Yb,Er crystals

The role of post synthesis annealing at different temperatures (200–600 °C) on the structural as well as luminescence properties of NaY_80%F₄:Yb_17%,Er_3% prepared via a coprecipitation method was found to change the structure from a cubic to hexagonal phase with a concomitant increase in upconversion luminescence by 12 times for the green region and 17 times for the red region. Addition of the Cr³⁺ ions (5–20 mol%) into the host followed by post annealing at 200–600 °C causes that the samples to exhibit phase dependent and upconversion luminescence behavior that depend upon the doping concentration as well as the annealing temperature. The inductively coupled optical emission spectroscopy reveals that only 1/600 times of the desired volume of the co-dopant goes to the lattice and it can manifest visible spectral changes in the diffuse reflectance spectra of the samples. The samples co-doped with Cr³⁺ ion concentrations of 10–15% and post-annealed at 600 °C were found to have maximum emission with an enhancement factor of 24 for the green region and 33 for the red region. In addition, the laser power dependent studies reveal that even for the power density levels 3.69 W cm⁻² to 32.14 W cm⁻², the samples are in the saturation regime and most of the samples investigated here follow a single photon process, and a few samples show a slope value less than 1 for laser power dependent intensity plots. The results show the remarkable promise of controlled tailoring of the properties of upconversion crystals via post annealing and co-doping.

Co-dopant (Cr³⁺ ion) concentration as well as post annealing found to change the structural as well as luminescence properties of Cr³⁺ ion doped NaY_80%F₄:Yb_17%,Er_3% prepared via a co-precipitation method.

Improving photoelectrochemical reduction of Cr(VI) ions by building α-Fe2O3/TiO2 electrode

Photoelectrochemical process is an environmentally friendly technology and has a wide application in the control of environmental pollutants. Efficient nanophotocatalysts responsive to visible light are still highly attractive. In this work, α-Fe₂O₃/TiO₂ were grown on fluorine doped tin oxide (FTO) substrates by hydrothermal method for photoelectrochemical reduction of Cr(VI). Compared with the separate α-Fe₂O₃ and TiO₂ electrodes, the composite α-Fe₂O₃/TiO₂ electrodes show higher photocurrent density. Under visible light irradiation, 100% removal efficiency of Cr(VI) was obtained after 40 min treatment. The composite α-Fe₂O₃/TiO₂ electrodes showed an enhanced absorbance in visible light region and had good stability to photoelectrochemical reduction of Cr(VI). The role of hole scavengers (citric acid and oxalic acid) and pH values was systematically investigated. This novel intensification approach provides new insight on the application of photoelectrochemical reduction in environmental remediation.

Simultaneous Cr(VI) bio-reduction and methane production by anaerobic granular sludge

Wastewater containing toxic hexavalent chromium (Cr(VI)) were treated with well-organized anaerobic granular sludge in this study. Results showed that the anaerobic granular sludge rapidly removed Cr(VI), and 2000 µg·L^-1 Cr(VI) was completely eliminated within 6 min, which was much faster than the reported duration of removal by reported artificial materials. Sucrose added as a carbon source acted as an initial electron donor to reduce Cr(VI) to Cr(III). This process was considered as the main mechanism of Cr(VI) removal. Methane production by anaerobic granular sludge was improved by the addition of Cr(VI) at a concentration lower than 500 µg·L^-1. Anaerobic granular sludge had a well-organized structure, which presented good resistance against toxic Cr(VI). Trichoccus accelerated the degradation of organic substances to generate acetates with a low Cr(VI) concentration, thereby enhancing methane production by acetotrophic methanogens.

Nitrogen-Containing Fabric Adsorbents Prepared by Radiation Grafting for Removal of Chromium from Wastewater

To remove chromium from wastewater effectively, two types of nitrogen-containing fabric adsorbents, having amidoxime ligand groups and quaternary ammonium anion exchange groups, respectively, were prepared by radiation grafting. In brief, the amidoxime adsorbent is obtained by grafting of acrylonitrile (AN)/methacrylic acid (MAA) onto a nonwoven fabric and subsequent amidoximation with hydroxylamine, while the ammonium adsorbent is obtained by grafting of chloromethylstyrene (CMS) followed by quaternization with trimethylamine. The AN/MAA-grafting reaches a high degree of grafting more than 100%, and the resulting amidoxime adsorbent reaches a high amidoxime density of 4.53 mmol/g. On the other hand, the CMS-grafting reaches a much higher degree of grafting above 200%, and the resulting ammonium adsorbent reaches a high ammonium density of 3.51 mmol/g. FTIR/ATR and TGA/DTA are used for the characterization of the grafted fabrics as well as the relevant fabric adsorbents. Furthermore, the chromium removal of the prepared fabric adsorbent is tested in both batch and column modes. It has been confirmed that the chromium removal was largely dependent on the pH of the solution. At pH 5.0, the amidoxime adsorbent shows a high Cr(III) adsorption capacity of 31.68 mg/g, while the ammonium adsorbent shows a much higher Cr(VI) adsorption capacity of 130.65 mg/g.

Light triggered interfacial damage self-healing of poly(p-phenylene benzobisoxazole) fiber composites

The interfacial microcracks in the resin matrix composites are difficult to be detected and repaired. However, the self-healing concept provides opportunities to fabricate composites with unusual properties. In the present study, photothermal conversion Ag-Cu₂S nanoparticles were immobilized onto poly(p-phenylene benzobisoxazole) (PBO) fibers via a polydopamine chemistry. Benefitting from the photothermal effects of Ag-Cu₂S, the obtained PBO fibers (Ag-Cu₂S-PBO) efficiently converted the light energy into heat under Xenon lamp irradiation. Then, single PBO fiber composites were prepared using thermoplastic polyurethane as the matrix. It was found that the interfacial damage caused by single fiber pull-out was simply self-healed by Xe light irradiation. This wonderful interfacial damage self-healing property was mainly attributed to the in situ heating generation via photothermal effects of Ag-Cu₂S in the composite interface. This paper reports a novel strategy to construct advanced composites with light-triggered self-healing properties, which will provide inspiration for preparing high performance composite materials.

Facile synthesis of hierarchical nickel (III) oxide nanostructure: A synergistic remediating action towards water contaminants

Heavy metal ion removal from consumable water is an indispensable need to maintain healthy life. Therefore cost effective and highly efficient sorbents are strongly needed to pose threat to real water pollution. Nanomaterials are widely used to maintain clean aqueous system in a very cost effective way with high removal efficiency. In this present work, pure coral like Ni₂O₃ nanostructures were prescribed for Cr(VI) remediation which were prepared by two step synthesis procedure at room temperature. The single hierarchical morphology as confirmed from HRTEM (size∼200 nm) were subjected to toxic Cr(VI) ion removal experiments. They were found to remove ∼65% Cr(VI) ions that was higher than that of pure Ni₂O₃ nanoparticles of comparable size. The enhanced properties were explained on the basis of the defect states present within the nanostructure, investigated by positron annihilation lifetime spectroscopy (PALS). It was found that the hierarchical nanostructure had more number of di-vacancies and vacancy-clusters as compared to the particles. On performing isotherm fitting, it was found that the coral like morphology had a high heterogeneity factor that aided to a high adsorption rate when compared to the pure Ni₂O₃ nanoparticles (which had a homogenous surface). The synthesized nanostructure was severely toxic to bacterial community having minimum inhibitory concentration (MIC) of ∼300 μg/L. Also the nanostructure exhibited dual functionality towards Cr(VI) and bacteria contaminated water at 200 μg/ml. The maximum Cr(VI) removal efficiency for this dual system is found to be 39% whereas antibacterial activity was turned out to be 30% which was extensively higher than that of toxic Cr(VI) ions. A plausible mechanism for the dual functionality was also predicted.

Polyaniline-based adsorbents for removal of hexavalent chromium from aqueous solution: a mini review

Hexavalent chromium (Cr(VI)) is a common hazardous contaminant in the environment and carcinogenic or mutagenic to aquatic animals and human beings. Therefore, the removal and detoxification of Cr(VI) have been attracting increasing attention of researchers. Among various conducting polymers, polyaniline (PANI)-based adsorbents have shown an excellent performance on the removal of Cr(VI) because of their redox properties, eased synthesis, and favorable biocompatibility. In this review, the characteristics of various PANI-based adsorbents were described, including PANI-modified nanofiber mats and membranes, PANI/bio-adsorbents, PANI/magnetic adsorbents, PANI/carbon adsorbents, PANI-modified clay composites, and PANI-inorganic hybrid composites. The mechanisms for the detoxification and adsorption of Cr(VI) were also discussed. The results indicated the potential applications of PANI-based adsorbents for the removal of Cr(VI). Graphical abstract ᅟ.

Characterization of Penicillium oxalicum SL2 isolated from indoor air and its application to the removal of hexavalent chromium

Removal of toxic Cr(VI) by microbial reduction is a promising approach to reducing its ecotoxicological impact. To develop bioremediation technologies, many studies have evaluated the application of microorganisms isolated from Cr(VI)-contaminated sites. Nonetheless, little attention has been given to microbes from the environments without a history of Cr(VI) contamination. In this study, we aimed to characterize the Cr(VI) tolerance and removal abilities of a filamentous fungus strain, SL2, isolated from indoor air. Based on phenotypic characterization and rDNA sequence analysis, SL2 was identified as Penicillium oxalicum, a species that has not been extensively studied regarding Cr(VI) tolerance and reduction abilities. SL2 showed high tolerance to Cr(VI) on solid and in liquid media, facilitating its application to Cr(VI)-contaminated environments. Growth curves of SL2 in the presence of 0, 100, 400, or 1000 mg/L Cr(VI) were well simulated by the modified Gompertz model. The relative maximal colony diameter and maximal growth rate decreased as Cr(VI) concentration increased, while the lag time increased. SL2 manifested remarkable efficacy of removing Cr(VI). Mass balance analysis indicated that SL2 removed Cr(VI) by reduction, and incorporated 0.79 mg of Cr per gram of dry biomass. In electroplating wastewater, the initial rate of Cr(VI) removal was affected by the initial contaminant concentration. In conclusion, P. oxalicum SL2 represents a promising new candidate for Cr(VI) removal. Our results significantly expand the knowledge on potential application of this microorganism.

Hexavalent chromium ion and methyl orange dye uptake via a silk protein sericin–chitosan conjugate

Sericin, a protein waste product of the silk industry, was crosslinked with chitosan, and a chitosan–sericin conjugate (CS) was prepared, characterized and used to remove hexavalent chromium (Cr(vi)) ions and methyl orange (MO) dye from aqueous solutions. The CS was shown to effectively remove Cr(vi) ions and MO dye at maximum adsorption capacities (Langmuir) of 139 mg g⁻¹ for Cr(vi) ions and 385 mg g⁻¹ for MO dye. Moreover, the adsorption of both Cr(vi) ions and MO dye was highly pH dependent and varied under different experimental conditions. Cr(vi) ion and MO dye uptake by the CS was confirmed by attenuated total reflectance Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy (XPS) and energy dispersive spectrometry analysis. Additionally, XPS analysis of the Cr(vi)-loaded CS revealed that Cr(vi) was reduced to the less toxic Cr(iii). The CS was shown not only to be highly amenable to regeneration, but also to be able to effectively remove MO dye and Cr(vi) ions from a binary mixture.

Sericin, a protein waste product of the silk industry, was crosslinked with chitosan, and a chitosan–sericin conjugate (CS) was prepared, characterized and used to remove hexavalent chromium (Cr(vi)) ions and methyl orange dye from aqueous solutions.

Synthesis and characterization of graphene/carbonized paper/tannic acid for flexible composite electrodes

A simple and low-cost approach toward flexible and free-standing electrodes is developed.

Synthesis of thorium–ethanolamine nanocomposite by the co-precipitation method and its application for Cr(vi) removal

Studies on the adsorption of Cr(vi) from water by a thorium ethanolamine nanocomposite.

A Comparative Study of Raw and Metal Oxide Impregnated Carbon Nanotubes for the Adsorption of Hexavalent Chromium from Aqueous Solution

The present study reports the use of raw, iron oxide, and aluminum oxide impregnated carbon nanotubes (CNTs) for the adsorption of hexavalent chromium (Cr(VI)) ions from aqueous solution. The raw CNTs were impregnated with 1% and 10% loadings (weight %) of iron oxide and aluminum oxide nanoparticles using wet impregnation technique. The synthesized materials were characterized using scanning electron microscopy (SEM) and thermogravimetric analysis (TGA). Batch adsorption experiments were performed to assess the removal efficiency of Cr(VI) ions from water and the effects of pH, contact time, adsorbent dosage, and initial concentration of the Cr(VI) ions were investigated. Results of the study revealed that impregnated CNTs achieved significant increase in the removal efficiency of Cr(VI) ions compared to raw CNTs. In fact, both CNTs impregnated with 10% loading of iron and aluminum oxides were able to remove up to 100% of Cr(VI) ions from aqueous solution. Isotherm studies were carried out using Langmuir and Freundlich isotherm models. Adsorption kinetics of Cr(VI) ions from water was found to be well described by the pseudo-second-order model. The results suggest that metallic oxide impregnated CNTs have very good potential application in the removal of Cr(VI) ions from water resulting in better environmental protection.

Effective Adsorption/Reduction of Cr(VI) Oxyanion by Halloysite@Polyaniline Hybrid Nanotubes

Halloysite@polyaniline (HA@PANI) hybrid nanotubes are synthesized by the in situ chemical polymerization of aniline on halloysite clay nanotubes. By facilely tuning the dopant acid, pH, and apparent weight proportion for aniline (ANI) and halloysite (HA) nanotubes in the synthesis process, PANI with tuned oxidation state, doping extent, and content are in situ growing on halloysite nanotubes. The reaction system's acidity is tuned by dopant acid, such as HCl, H₂SO₄, HNO₃, and H₃PO₄. The adsorption result shows the fabricated HA@PANI hybrid nanotubes can effectively adsorb Cr(VI) oxyanion and the adsorption ability changes according to the dopant acid, pH, and apparent weight proportion for ANI and HA in the synthesis process. Among them, the HA@PANI fabricated with HCl as dopant acid tuning the pH at 0.5 and 204% apparent weight proportion for ANI and HA (HP/0.5/204%-HCl) shows the highest adsorption capacity. The adsorption capacity is in accordance well with the doping extent of PANI in HA@PANI. Furthermore, when HP/0.5/204%-HCl is redoped with HNO₃, H₂SO₄, and H₃PO₄, the adsorption capacity declines, implying the dopant acid in the process of redoping exhibits a marked effect on Cr(VI) oxyanion adsorption for the HA@PANI hybrid nanotubes. HP/0.5/204%-HCl and HP/0.5/204%-H₃PO₄ have demonstrated good regenerability with an above 80% removal ratio after four cycles. Moreover, the HA@PANI adsorbent has better sedimentation ability than that of pure PANI. The adsorption behavior is in good agreement with Langmuir and pseudo second-order equations, indicating the adsorption of HA@PANI for Cr(VI) oxyanion is chemical adsorption. FT-IR and XPS of HA@PANI after Cr(VI) oxyanion adsorption indicate that the doped amine/imine groups (-NH⁺/═N⁺- groups) are the main adsorption sites for the removal of Cr(VI) oxyanion by electrostatic adsorption and reduction of the adsorbed Cr (VI) oxyanion to Cr(III) simultaneously.

Exfoliation of a two-dimensional cationic inorganic network as a new paradigm for high-capacity CrVI-anion capture

This work represents the selective capture of the aqueous Cr^VI-anions in record capacityviathein situexfoliation of a rare cationic copper hydroxide material.

Flexible Electrospun Carbon Nanofiber/Tin(IV) Sulfide Core/Sheath Membranes for Photocatalytically Treating Chromium(VI)-Containing Wastewater

We report an efficient method for fabricating flexible membranes of electrospun carbon nanofiber/tin(IV) sulfide (CNF@SnS₂) core/sheath fibers. CNF@SnS₂ is a new photocatalytic material that can be used to treat wastewater containing high concentrations of hexavalent chromium (Cr(VI)). The hierarchical CNF@SnS₂ core/sheath membranes have a three-dimensional macroporous architecture. This provides continuous channels for the rapid diffusion of photoelectrons generated by SnS₂ nanoparticles under visible light irradiation. The visible light (λ > 400 nm) driven photocatalytic properties of CNF@SnS₂ are evaluated by the reduction of water-soluble Cr(VI). CNF@SnS₂ exhibits high visible light-driven photocatalytic activity because of its low band gap of 2.34 eV. Moreover, CNF@SnS₂ exhibits good photocatalytic stability and excellent cycling stability. Under visible light irradiation, the optimized CNF@SnS₂ membranes exhibit a high rate of degradation of 250 mg/L of aqueous Cr(VI) and can completely degrade the Cr(VI) within 90 min.

Fabrication of Unique Magnetic Bionanocomposite for Highly Efficient Removal of Hexavalent Chromium from Water

Biotreatment of hexavalent chromium has attracted widespread interest due to its cost effective and environmental friendliness. However, the difficult separation of biomass from aqueous solution and the slow hexavalent chromium bioreduction rate are bottlenecks for biotechnology application. In this approach, a core-shell structured functional polymer coated magnetic nanocomposite was prepared for enriching the hexavalent chromium. Then the nanocomposite was connected to the bacteria via amines on bacterial (Bacillus subtilis ATCC-6633) surface. Under optimal conditions, a series of experiments were launched to degrade hexavalent chromium from the aqueous solution using the as-prepared bionanocomposite. Results showed that B. subtilis@Fe3O4@mSiO2@MANHE (BFSM) can degrade hexavalent chromium from the water more effectively (a respectable degradation efficiency of about 94%) when compared with pristine B. subtilis and Fe3O4@mSiO2@MANHE (FSM). Moreover, the BFSM could be separated from the wastewater by magnetic separation technology conveniently due to the Fe3O4 core of FSM. These results indicate that the application of BFSM is a promising strategy for effective treating wastewater containing hexavalent chromium.

A comparative study with biologically and chemically synthesized nZVI: applications in Cr (VI) removal and ecotoxicity assessment using indigenous microorganisms from chromium-contaminated site

In the present communication, we report a comparative study of Cr (VI) removal using biologically synthesized nano zero valent iron (BS-nZVI) and chemically synthesized nZVI (CS-nZVI), both immobilized in calcium alginate beads. The parameters like initial Cr (VI) concentration, nZVI concentration, and the contact time for Cr (VI) removal were optimized based on Box-Behnken design (BBD) by response surface modeling at a constant pH 7. Under the optimized conditions (concentration of nZVI = 1000 mg L(-1), contact time = ∼ 80 min, and initial concentration of Cr (VI) = 10 mg L(-1)), the Cr (VI) removal by the immobilized BS-nZVI and CS-nZVI alginate beads was 80.04 and 81.08 %, respectively. The adsorption of Cr (VI) onto the surface of alginate beads was confirmed by scanning electron microscopy with energy-dispersive x-ray spectroscopy (SEM-EDX), Fourier transform infrared spectroscopy (FT-IR), and Brunauer-Emmett-Teller (BET) analysis. The applicability of the process using both the sorbents was successfully test medium Cr (VI) spiked environmental water samples. In order to assess the ecotoxic effects of nZVI, the decline in cell viability, generation of intracellular reactive oxygen species (ROS), cell membrane damage, and biouptake was studied at 1000 mg L(-1) concentration, with five indigenous bacterial isolates from chromium-contaminated lake sediments and their consortium.

Remediation of Cd(ii)-contaminated soil by three kinds of ferrous phosphate nanoparticles

Three kinds of iron phosphate nanoparticles were synthesized and they could reduce leachability and bioaccessibility of Cd effectively.

Kinetics, equilibrium isotherm and neural network modeling studies for the sorption of hexavalent chromium from aqueous solution by quartz/feldspar/wollastonite

A three layer feed forward artificial neural network (ANN) with back propagation training algorithm was developed to model the adsorption process of Cr(vi) in aqueous solution using riverbed sand containing quartz/feldspar/wollastonite (QFW) as adsorbent.