Graphene oxide based smart fluids

Development of a Performance-Enhanced Hybrid Magnetorheological Elastomer-Fluid for Semi-Active Vibration Isolation: Static and Dynamic Experimental Characterization

Magnetorheological elastomers (MREs) are a class of emerging smart materials in which their mechanical and rheological properties can be immediately and reversibly altered upon the application of a magnetic field. The change in the MRE properties under the magnetic field is widely known as the magnetorheological (MR) effect. Despite their inherent viscoelastic property-change characteristics, there are disadvantages incorporated with MREs, such as slow response time and the suspension of the magnetic particles in the elastomer matrix, which depress their MR effect. This study investigates the feasibility of a hybrid magnetorheological elastomer-fluid (MRE-F) for longitudinal vibration isolation. The hybrid MRE-F is fabricated by encapsulating MR fluid inside the elastomer matrix. The inclusion of the MR fluid can enhance the MR effect of the elastomer by providing a better response to the magnetic field and, hence, can improve the vibration isolation capabilities. For this purpose, an MRE-based coupling is developed, and isolation performance is investigated in terms of the linear transmissibility factor. The performance of the hybrid MRE-F was compared against two different MRE samples. The results show that further enhancement of MR-effect in MREs is possible by including MR fluid inside the elastomer. The hybrid MRE-F exhibited better stiffness change with the current increase and recorded the highest value of 55.911 N/mm. The transmissivity curves revealed that the MRE-F contributed to a broader shift in the natural frequency with a 7.2 Hz overall shift at 8.9 mT. The damping characteristics are higher in MRE-F, recording the highest percentage increase in damping with 33.04%. Overall, the results reveal the promising potential of hybrid MRE-F in developing MRE-based coupling for longitudinal vibration isolation.

Electrorheological Fluids of GO/Graphene-Based Nanoplates

Due to their unique anisotropic morphology and properties, graphene-based materials have received extensive attention in the field of smart materials. Recent studies show that graphene-based materials have potential application as a dispersed phase to develop high-performance electrorheological (ER) fluids, a kind of smart suspension whose viscosity and viscoelastic properties can be adjusted by external electric fields. However, pure graphene is not suitable for use as the dispersed phase of ER fluids due to the electric short circuit caused by its high electrical conductivity under electric fields. However, graphene oxide (GO) and graphene-based composites are suitable for use as the dispersed phase of ER fluids and show significantly enhanced property. In this review, we look critically at the latest developments of ER fluids based on GO and graphene-based composites, including their preparation, electrically tunable ER property, and dispersed stability. The mechanism behind enhanced ER property is discussed according to dielectric spectrum analysis. Finally, we also propose the remaining challenges and possible developments for the future outlook in this field.

Reinforcing Magnetorheological Fluids with Highly Anisotropic 2D Materials

Magnetorheological fluids (MRF) are suspensions of magnetic particles that solidify in the presence of a magnetic field. While non-magnetic additives could improve MRF performance, explorations into such additives have not coalesced into an understanding of their influence, and particularly the role of additive morphology. Here, we explore α-Ni(OH)₂ 2D sheets, with aspect ratios of ∼25,000, as highly anisotropic MRF additives. Experiments studying pressure-driven flow of an MRF with and without these sheets show that their addition can increase the saturation pressure by as much as 46 %. However, shear-mode rheology reveals that they can also weaken the MRF by inhibiting the chaining of the iron particles at low field strengths and have no effect at higher field strengths. In order to reconcile the strikingly different results, we propose that 2D materials introduce a non-Newtonian handle to modify smart fluids in a manner that depends on the curvature of the shearing strain rate profile. Specifically, we identify a modification to the Buckingham-Reiner model of pressure-driven flow for a Bingham plastic in which the sheets widen the solidified plug. This work highlights the subtle interaction between particles in smart fluids and flows while emphasizing the opportunity for using anisotropy to tune this interaction.

Enhanced electrorheological activity of porous chitosan particles

Novel porous filler for electrorheological fluids was fabricated from chitosan via freeze drying technique. An exceptional electrorheological effect was discovered in suspensions of polydimethylsiloxane (silicone oil) filled by highly porous chitosan particles. The electrorheological activity was studied by rotational rheometry and visualized by optical microscopy. High porosity of the filler allows preparing highly efficient electrorheological fluids at rather low (< 1 wt%) concentration of dispersed phase. The mechanism of chain-like structure formation was considered. The electrorheological behavior of suspensions and the filler structural organization at different concentration were comprehended in terms of dielectric properties. The rheological data were approximated by Bingham and Cho-Choi-Jhon equations. The sedimentation stability of chitosan suspensions in polydimethylsiloxane was significantly affected by particles porosity.

Dielectric Polarization and Electrorheological Response of Poly(ethylaniline)-Coated Reduced Graphene Oxide Nanoflakes with Different Reduction Degrees

We prepared poly(ethylaniline)-coated graphene oxide nanoflakes and then treated them with different concentrations of hydrazine solution to form dielectric composite nanoflakes having different reduction degrees of reduced graphene oxide core and insulating polyethylaniline shell (PEANI/rGO). The morphology of PEANI/rGO was observed by scanning electron microscopy, while the chemical structure was confirmed by Fourier transform infrared spectroscopy and X-ray photoelectron spectrometer. The influence of reduction degrees on the conductivity, dielectric polarization and electrorheological effect of PEANI/rGO in suspensions was investigated by dielectric spectroscopy and rheological test under electric fields. It shows that the PEANI/rGO has two interfacial polarization processes respectively due to rGO core and PEANI shell. As the number of hydrazine increases, the conductivity and polarization rate of rGO core increase. As a result, the difference between the polarization rate of rGO core and that of the PEANI shell gradually becomes large. This increased difference does not significantly decrease the yield stress but causes the flow instability of PEANI/GO suspensions under the simultaneous action of electric and shear fields.

Melt Rheology and Mechanical Characteristics of Poly(Lactic Acid)/Alkylated Graphene Oxide Nanocomposites

Poly(lactic acid) (PLA) nanocomposites were synthesized by a solution blending and coagulation method using alkylated graphene oxide (AGO) as a reinforcing agent. Turbiscan confirmed that the alkylation of GO led to enhanced compatibility between the matrix and the filler. The improved dispersity of the filler resulted in superior interfacial adhesion between the PLA chains and AGO basal plane, leading to enhanced mechanical and rheological properties compared to neat PLA. The tensile strength and elongation at break, i.e., ductility, increased by 38% and 42%, respectively, at the same filler content nanocomposite (PLA/AGO 1 wt %) compared to nonfiller PLA. Rheological analysis of the nanocomposites in the molten state of the samples was performed to understand the filler network formed inside the matrix. The storage modulus increased significantly from PLA/AGO 0.5 wt % (9.6 Pa) to PLA/AGO 1.0 wt % (908 Pa). This indicates a percolation threshold between the two filler contents. A steady shear test was performed to examine the melt flow characteristics of PLA/AGO nanocomposites at 170 °C, and the viscosity was predicted using the Carreau-Yasuda model.

Magnetorheological Elastomers: Fabrication, Characteristics, and Applications

Magnetorheological (MR) elastomers become one of the most powerful smart and advanced materials that can be tuned reversibly, finely, and quickly in terms of their mechanical and viscoelastic properties by an input magnetic field. They are composite materials in which magnetizable particles are dispersed in solid base elastomers. Their distinctive behaviors are relying on the type and size of dispersed magnetic particles, the type of elastomer matrix, and the type of non-magnetic fillers such as plasticizer, carbon black, and crosslink agent. With these controllable characteristics, they can be applied to various applications such as vibration absorber, isolator, magnetoresistor, and electromagnetic wave absorption. This review provides a summary of the fabrication, properties, and applications of MR elastomers made of various elastomeric materials.

Sensing and monitoring of edifenphos molecules based on the quantum chemical approach

The tendency of edifenphos (EDF) species toward boron carbide nanotube (BC₃NT) was investigated through density functional theory (DFT) calculations with perfect and defected forms. It was found that perfect BC₃NT tube is not capable to adsorb the EDF molecules appropriately. Introducing defects in BC₃NT lattice resulted in a noticeable enhancement of interaction with EDF providing the adsorption energy of - 25.66 kcal/mol. It was predicted that the conductivity of complex formed of single vacancy BC₃NT tube, SV-BC₃NT, and EDF complexes is enhanced by 91.37 times compared with BC₃NT tube with no defects. As the solvent dielectric constant increases, a significant change in adsorption energy was reported while slighter variation was observed at dielectric constant values lower than 15. Similar to electric conductivity, the magnetic properties of BC₃NT are remarkably enhanced after single vacancy defect and EDF adsorption leads to a highly significant change in magnetic property compared with perfect BC₃NT. Graphical abstract.

Effect of Structure of Polymers Grafted from Graphene Oxide on the Compatibility of Particles with a Silicone-Based Environment and the Stimuli-Responsive Capabilities of Their Composites

This study reports the utilization of controlled radical polymerization as a tool for controlling the stimuli-responsive capabilities of graphene oxide (GO) based hybrid systems. Various polymer brushes with controlled molecular weight and narrow molecular weight distribution were grafted from the GO surface by surface-initiated atom transfer radical polymerization (SI-ATRP). The modification of GO with poly(n-butyl methacrylate) (PBMA), poly(glycidyl methacrylate) (PGMA), poly(trimethylsilyloxyethyl methacrylate) (PHEMATMS) and poly(methyl methacrylate) (PMMA) was confirmed by thermogravimetric analysis (TGA) coupled with online Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). Various grafting densities of GO-based materials were investigated, and conductivity was elucidated using a four-point probe method. Raman shift and XPS were used to confirm the reduction of surface properties of the GO particles during SI-ATRP. The contact angle measurements indicated the changes in the compatibility of GOs with silicone oil, depending on the structure of the grafted polymer chains. The compatibility of the GOs with poly(dimethylsiloxane) was also investigated using steady shear rheology. The tunability of the electrorheological, as well as the photo-actuation capability, was investigated. It was shown that in addition to the modification of conductivity, the dipole moment of the pendant groups of the grafted polymer chains also plays an important role in the electrorheological (ER) performance. The compatibility of the particles with the polymer matrix, and thus proper particles dispersibility, is the most important factor for the photo-actuation efficiency. The plasticizing effect of the GO-polymer hybrid filler also has a crucial impact on the matrix stiffness and thus the ability to reversibly respond to the external light stimulation.

Enhanced and Tunable Electrorheological Capability using Surface Initiated Atom Transfer Radical Polymerization Modification with Simultaneous Reduction of the Graphene Oxide by Silyl-Based Polymer Grafting

In this study, a verified process of the "grafting from" approach using surface initiated atom transfer radical polymerization was applied for the modification of a graphene oxide (GO) surface. This approach provides simultaneous grafting of poly(2-(trimethylsilyloxy)ethyl methacrylate) (PHEMATMS) chains and a controllable reduction of the GO surface. This allows the fine tuning of its electrical conductivity, which is a crucial parameter for applications of such hybrid composite particles in electrorheological (ER) suspensions. The successful coating was confirmed by transmission electron microscopy and Fourier-transform infrared spectroscopy. The molecular characteristics of PHEMATMS were characterized by gel permeation chromatography. ER performance was elucidated using a rotational rheometer under various electric field strengths and a dielectric spectroscopy to demonstrate the direct impact of both the relaxation time and dielectric relaxation strength on the ER effectivity. Enhanced compatibility between the silicone oil and polymer-modified GO particles was investigated using contact angle measurements and visual sedimentation stability determination. It was clearly proven that the modification of the GO surface improved the ER capability of the system due to the tunable conductivity during the surface-initiated atom transfer radical polymerization (SI-ATRP) process and the enhanced compatibility of the GO particles, modified by polymer containing silyl structures, with silicone oil. These unique ER properties of this system appear very promising for future applications in the design of ER suspensions.

Enhanced Electrorheological Performance of Mixed Silica Nanomaterial Geometry

The mixed geometrical effect on the electrorheological (ER) activity of bimodal ER fluids was investigated by mixing SiO₂ spheres and rods of different dimensions. To gain an in-depth understanding of the mixed geometrical effect, 12 bimodal ER fluids were prepared from 4 sizes of SiO₂ spheres (50, 100, 150, and 350 nm) and 3 types of SiO₂ rods with different aspect ratios (L/D = 2, 3, and 5). Five concentrations of SiO₂ spheres and rods were created for each bimodal ER fluid, resulting in a total of 60 sets of comprehensive ER measurements. Some bimodal ER fluids exhibited enhanced ER performance, as high as 23.0%, compared to single SiO₂ rod-based ER fluids to reveal the mixed geometrical effect of bimodal ER fluids. This interesting experimental result is based on the structural reinforcement provided by spheres to fibrillated rod materials, demonstrating the mixed geometrical effect on ER activity.

Electro-response of MoS2 Nanosheets-Based Smart Fluid with Tailorable Electrical Conductivity

The correlation between electrical conductivity and electro-responsive behavior is identified by introducing few-layer molybdenum disulfide (MoS2) nanosheets to electrorheological (ER) fluid. Few-layer MoS2 nanosheets are successfully fabricated, with a high yield of above 60%, using a straightforward method, and applied to an electro-responsive smart fluid. The electrical conductivity of MoS2 is easily tunable by adjusting the annealing temperature because of its semiconducting behavior. From an in-depth study on the conductivity-dependent ER behavior of few-layer MoS2 nanosheets, it can be verified that an optimum value of the electrical conductivity exists for the electro-responsive material, corresponding to the Wagner model. To the best of our knowledge, this is the first report on the potential of a transition-metal dichalcogenide as a candidate material for an ER fluid. This study may provide promising approaches for the performance improvement of electro-responsive smart fluids.

Large scale and facile sonochemical synthesis of magnetic graphene oxide nanocomposites and their dual electro/magneto-stimuli responses

Magnetic Fe₃O₄/GO nanocomposites have been prepared via an effective electrostatic strategy under ultrasonic waves. Their appealing dual electro/magnetorheological (ER/MR) performances were investigated under applied electric or magnetic fields.

Tunable electrorheological characteristics and mechanism of a series of graphene-like molybdenum disulfide coated core–shell structured polystyrene microspheres

Core–shell structured molybdenum disulfide (MoS₂) coated polystyrene (PS) microspheres are synthesized with the help of hexadecyl trimethyl ammonium bromide (CTAB) through negative–positive electrostatic attraction.

Enhanced magnetorheological performance of highly uniform magnetic carbon nanoparticles

Magnetic carbon nanoparticles (MC NPs) are prepared on a multi-gram scale through carbonization of iron-doped polypyrrole nanoparticles (PPy NPs). Three different-sized MC NPs (ca. 40, 60 and 90 nm) are prepared and adopted as dispersing materials for magnetorheological (MR) fluids to investigate the influence of particle size on MR properties. The MC NP-based MR fluids exhibit outstanding MR performances compared to the conventional magnetic carbon material-based fluids. In addition, the MR activities are enhanced with decreasing particle diameter and increasing applied magnetic field strength. Furthermore, anti-sedimentation properties are examined in order to achieve in-depth insight into the effect of the particle size on MR fluids.

Celebrating Soft Matter's 10th anniversary: stimuli-responsive Pickering emulsion polymerized smart fluids

The Pickering emulsion process is an important and interesting way of forming hybrid soft matter particles stabilized by solid particles as surfactants instead of the extensive use of conventionally available organic surfactant molecules. This Highlight briefly reviews stimuli-responsive polymer/inorganic hybrid materials fabricated by Pickering emulsion polymerization along with the rheological characteristics of their electrorheological and magnetorheological smart fluids under electric and magnetic fields, respectively.

Graphene oxide modified by betaine moieties for improvement of electrorheological performance

Novel graphene oxide bearing betaine moieties as sulfobetaine (GO-SB), carboxybetaine (GO-CB) and carboxybetaine ester (GO-CBE) moieties were prepared in two simple fabrication processes based on silanization and a thiol–ene click-reaction.

Latex routes to graphene-based nanocomposites

This review article describes recent advances in the elaboration of graphene-based colloidal nanocomposites by the use of graphene or graphene oxide in heterophase polymerization systems.

Facile synthesis of polyaniline nanotubes and their enhanced stimuli-response under electric fields

Polyaniline (PANI) nanotubes were fabricated successfully using a micelle soft-template method in the presence of oxalic acid as a dopant and applied as the dispersed phase of an electrorheological (ER) fluid.