Comparative In Vitro Dissolution Assessment of Calcined and Uncalcined Hydroxyapatite Using Differences in Bioresorbability and Biomineralization

This study reports the effect of the not-calcining process on the bioresorption and biomineralization of hydroxyapatite through in vitro dissolution assessment. The prepared calcined hydroxyapatite (c-HAp) and uncalcined hydroxyapatite (unc-HAp) have a particle size of 2 μm and 13 μm, surface areas of 4.47 m2/g and 108.08 m2/g, and a Ca/P ratio of 1.66 and 1.52, respectively. In vitro dissolution assessments of c-HAp and unc-HAp were performed for 20 days at 37 °C in a citric acid buffer according to ISO 10993-14. During the dissolution, the c-HAp and unc-HAp confirmed an increase in weight, and the calcium and phosphorous ions were rapidly released. The calcium ions released from c-HAp formed rod-shaped particles with a longer and thinner morphology, while in unc-HAp, they appeared thicker and shorter. In the ICP-OES results, the concentrations of calcium elements were initially increased and then decreased by this formation. The rod-shaped particles identified as calcium citrate (Ca-citrate) through the XRD pattern. The calcium content of Ca-citrate particles from unc-HAp was higher than that from c-HAp. The unc-HAp demonstrated non-toxic properties in a cytotoxicity evaluation. Therefore, due to its higher bioresorption and biomineralization, unc-HAp exhibits enhanced biocompatibility compared to c-HAp.

Crystalline Micro-Sized Carbonated Apatites: Chemical Anisotropy of the Crystallite Surfaces, Biocompatibility, Osteoconductivity, and Osteoinductive Effect Enhanced by Poly(ethylene phosphoric acid)

Carbonated hydroxyapatites (CAp) are very close to natural bone apatite in chemical composition and are regarded as a prospective bone mineral substitute for bone surgery and orthopedics. However, until now, the studies and applications of CAp were limited because of the amorphous nature of the synthetic CAp. In the present work, microsized highly crystalline carbonated apatites with uniform hexagonal (hCAp) or platelike (pCAp) morphology have been studied for the first time in vitro and in vivo, comparing against commercial hydroxyapatite (HAp) and β-tricalcuim phosphate (βTCP). In vitro experiments on dissolution of those calcium phosphate ceramics (CPCs) in acetate (pH 5.5) and Tris (pH 7.3) buffer solutions showed the following rank order of the dissolution rates: βTCP > hCAp > pCAp > HAp. The higher dissolution rate of hCAp in comparison with pCAp is explained by chemical anisotropy of the crystallite surfaces, which was proven by SEM studies of the changes in the morphology of hCAp and pCAp crystallites during hydrolysis. A 5-week experiment on subcutaneous implantation of CPC species showed the following rank order of bioresorption rates: βTCP > pCAp > hCAp > HAp. pCAp matrixes exhibited the highest biocompatibility, confirmed by histomorphological analysis. Three-month bone regeneration experiments involving a rat tibial defect model were conducted with 250-500 μm granules of pCAp and pCAp-PEPA [pCAp, pretreated with 2 wt % poly(ethylene phosphoric acid)]. Notably, pCAp-PEPA implants were resorbed at higher rates and induced the formation of more mature osseous tissue, a compact bone with Haversian systems.

Gallium-Doped Hydroxyapatite: Shape Transformation and Osteogenesis Activity

In this study, we employed a chemical precipitation method to successfully synthesize nanoparticles of gallium-doped hydroxyapatite (Ga-HAp). The microstructure of Ga-HAp was precisely tailored by modulating the concentration of gallium ions. Our findings unequivocally demonstrate that gallium ions exert a pronounced inhibitory influence on the growth of HAp crystals, and this inhibitory potency exhibits a direct correlation with the concentration of gallium. Furthermore, gallium ions facilitate the metamorphosis of HAp nanoparticles, transitioning them from nanoneedles to nanosheets. It is worth noting, however, that gallium ions exhibit a limited capacity to substitute for calcium ions within the crystal lattice of HAp, with the maximum substitution rate capped at 4.85%. Additionally, gallium plays a pivotal role in constraining the release of ions from HAp, and this behavior remains consistent across samples with varying Ga doping concentrations. Our in vitro experiments confirm that Ga-doped HAp amplifies both the proliferation and osteogenic differentiation of bone marrow mesenchymal stem cells.

Dispersant and Protective Roles of Amphiphilic Poly(ethylene phosphate) Block Copolymers in Polyester/Bone Mineral Composites

Composites of synthetic bone mineral substitutes (BMS) and biodegradable polyesters are of particular interest for bone surgery and orthopedics. Manufacturing of composite scaffolds commonly uses mixing of the BMS with polymer melts. Melt processing requires a high homogeneity of the mixing, and is complicated by BMS-promoted thermal degradation of polymers. In our work, poly(L-lactide) (PLLA) and poly(ε-caprolactone) (PCL) composites reinforced by commercial β-tricalcium phosphate (βTCP) or synthesized carbonated hydroxyapatite with hexagonal and plate-like crystallite shapes (hCAp and pCAp, respectively) were fabricated using injection molding. pCAp-based composites showed advanced mechanical and thermal characteristics, and the best set of mechanical characteristics was observed for the PLLA-based composite containing 25 wt% of pCAp. To achieve compatibility of polyesters and pCAp, reactive block copolymers of PLLA or PCL with poly(tert-butyl ethylene phosphate) (C1 and C2, respectively) were introduced to the composite. The formation of a polyester-b-poly(ethylene phosphoric acid) (PEPA) compatibilizer during composite preparation, followed by chemical binding of PEPA with pCAp, have been proved experimentally. The presence of 5 wt% of the compatibilizer provided deeper homogenization of the composite, resulting in a marked increase in strength and moduli as well as a more pronounced nucleation effect during isothermal crystallization. The use of C1 increased the thermal stability of the PLLA-based composite, containing 25 wt% of pCAp. In view of positive impacts of polyester-b-PEPA on composite homogeneity, mechanical characteristics, and thermal stability, polyester-b-PEPA will find application in the further development of composite materials for bone surgery and orthopedics.

Building Osteogenic Microenvironments with a Double-Network Composite Hydrogel for Bone Repair

The critical factor determining the in vivo effect of bone repair materials is the microenvironment, which greatly depends on their abilities to promote vascularization and bone formation. However, implant materials are far from ideal candidates for guiding bone regeneration due to their deficient angiogenic and osteogenic microenvironments. Herein, a double-network composite hydrogel combining vascular endothelial growth factor (VEGF)-mimetic peptide with hydroxyapatite (HA) precursor was developed to build an osteogenic microenvironment for bone repair. The hydrogel was prepared by mixing acrylated β-cyclodextrins and octacalcium phosphate (OCP), an HA precursor, with gelatin solution, followed by ultraviolet photo-crosslinking. To improve the angiogenic potential of the hydrogel, QK, a VEGF-mimicking peptide, was loaded in acrylated β-cyclodextrins. The QK-loaded hydrogel promoted tube formation of human umbilical vein endothelial cells and upregulated the expression of angiogenesis-related genes, such as Flt1 , Kdr , and VEGF , in bone marrow mesenchymal stem cells. Moreover, QK could recruit bone marrow mesenchymal stem cells. Furthermore, OCP in the composite hydrogel could be transformed into HA and release calcium ions facilitating bone regeneration. The double-network composite hydrogel integrated QK and OCP showed obvious osteoinductive activity. The results of animal experiments showed that the composite hydrogel enhanced bone regeneration in skull defects of rats, due to perfect synergistic effects of QK and OCP on vascularized bone regeneration. In summary, improving the angiogenic and osteogenic microenvironments by our double-network composite hydrogel shows promising prospects for bone repair.

Macroporous Hyaluronic Acid/Chitosan Polyelectrolyte Complex-Based Hydrogels Loaded with Hydroxyapatite Nanoparticles: Preparation, Characterization and In Vitro Evaluation

The aim of the study was to fabricate and characterize composite macroporous hydrogels based on a hyaluronic acid/chitosan (Hyal/Ch) polyelectrolyte complex (PEC) loaded with homogeneously distributed hydroxyapatite nanoparticles (nHAp), and to evaluate them in vitro using mouse fibroblasts (L929), osteoblast-like cells (HOS) and human mesenchymal stromal cells (hMSC). Hydrogel morphology as a function of the hydroxyapatite nanoparticle content was studied using scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM). The mean pore size in the Hyal/Ch hydrogel was 204 ± 25 μm. The entrapment of nHAp (1 and 5 wt. %) into the Hyal/Ch hydrogel led to a mean pore size decrease (94 ± 2 and 77 ± 9 μm, relatively). Swelling ratio and weight loss of the hydrogels in various aqueous media were found to increase with an enhancement of a medium ionic strength. Cell morphology and localization within the hydrogels was studied by CLSM. Cell viability depended upon the nHAp content and was evaluated by MTT-assay after 7 days of cultivation in the hydrogels. An increase of the hydroxyapatite nanoparticles loading in a range of 1–10 wt. % resulted in an enhancement of cell growth and proliferation for all hydrogels. Maximum cell viability was obtained in case of the Hyal/Ch/nHAp-10 sample (10 wt. % nHAp), while a minimal cell number was found for the Hyal/Ch/nHAp-1 hydrogel (1 wt. % nHAp). Thus, the proposed simple original technique and the design of PEC hydrogels could be promising for tissue engineering, in particular for bone tissue repair.

Sustained Hyperglycemia and Its Relationship with the Outcome of Hospitalized Patients with Severe COVID-19: Potential Role of ACE2 Upregulation

Chronic hyperglycemia increases the risk of developing severe COVID-19 symptoms, but the related mechanisms are unclear. A mean glucose level upon hospital admission >166 mg/dl correlates positively with acute respiratory distress syndrome in patients with hyperglycemia. The objective of this study was to evaluate the relationship between sustained hyperglycemia and the outcome of hospitalized patients with severe COVID-19. We also evaluated the effect of high glucose concentrations on the expression of angiotensin-converting enzyme 2 (ACE2). We carried out a case-control study with hospitalized patients with severe COVID-19 with and without sustained hyperglycemia. In a second stage, we performed in vitro assays evaluating the effects of high glucose concentrations on ACE2 gene expression. Fifty hospitalized patients with severe COVID-19 were included, of which 28 (56%) died and 22 (44%) recovered. Patients who died due to COVID-19 and COVID-19 survivors had a high prevalence of hyperglycemia (96.4% versus 90.9%), with elevated central glucose upon admission (197.7 mg/dl versus 155.9 mg/dl, p = 0.089) and at discharge (185.2 mg/dl versus 134 mg/dl, p = 0.038). The mean hypoxemia level upon hospital admission was 81% in patients who died due to COVID-19 complications and 88% in patients who survived (p = 0.026); at the time of discharge, hypoxemia levels were also different between the groups (68% versus 92%, p ≤ 0.001). In vitro assays showed that the viability of A549 cells decreased (76.41%) as the glucose concentration increased, and the ACE2 gene was overexpressed 9.91-fold after 72 h (p ≤ 0.001). The relationship between hyperglycemia and COVID-19 in hospitalized patients with COVID-19 plays an important role in COVID-19-related complications and the outcome for these patients. In patients with chronic and/or sustained hyperglycemia, the upregulation of ACE2, and its potential glycation and malfunction, could be related to complications observed in patients with COVID-19.

A biomimetic approach to evaluate mineralization of bioactive glass-loaded resin composites

PURPOSE

This study explores novel solutions other than standard SBF for biomimetic evaluations of mineralization particularly for resin composites containing bioactive glass (BAG).

METHODS

Experimental UDMA/TEGDMA resin composites with 0.0, 1.9, 3.8 or 7.7 vol% of 45S5 BAG fillers were prepared. Besides simulated body fluid (SBF) as control, the specimens were immersed in three other solutions either with bicarbonate which are Hank's balanced salt solution (HBSS) and cell culture medium (MEM), or without bicarbonate which is a novel Simple HEPES-containing Artificial Remineralization Promotion (SHARP) solution, for 3, 7 and 14 days. These solutions were then analyzed by ICP-OES and pH, and the surfaces of the BAG composites were analyzed by SEM, XRD and FTIR.

RESULTS

ICP-OES revealed Ca and P concentration continuously decrease, while Si concentration increases with time in the solutions other than SBF, which showed almost unchanged elemental concentration. Only SHARP solution is able to maintain a constant pH over the immersion time. SEM, together with XRD and FTIR, showed nano-sized octacalcium phosphate (OCP) nanospheres formation on 3.8 and 7.7 vol% BAG composites after 14 days immersion in HBSS (500-600 nm) and MEM (300-400 nm). SHARP solution enabled OCP formation after 3 days and then self-assembled into urchin-like carbonated hydroxyapatite (CHA) microspheres encompassed with nanorods of 100 nm width and 8 µm length after 14 days of immersion for 7.7 vol% BAG composites.

CONCLUSION

This study suggests SHARP solution can evaluate mineralization biomimetically whereas CHA microspheres can be formed on BAG-containing resin composites.

Hydrothermal synthesis of perfectly shaped micro- and nanosized carbonated apatite

Herein we present a Ca[EDTA]-based synthesis and comparative study of perfectly shaped plate-like, rod–like, and prism-like carbonated apatites.

Bifunctional scaffolds of hydroxyapatite/poly(dopamine)/carboxymethyl chitosan with osteogenesis and anti-osteosarcoma effect

Bifunctional scaffolds prepared by hydroxyapatite/poly(dopamine)/carboxymethyl chitosan with good osteogenesis and anti-osteosarcoma effect is promising for bone tumor therapy.

Facile synthesis of copper doping hierarchical hollow porous hydroxyapatite beads by rapid gelling strategy

Calcium phosphate based ceramic materials are widely used in bone tissue engineering. Till now, it remains an unmet challenge to construct monodispersed hollow porous calcium phosphate beads through facile and scalable-production strategy. Herein, a rapid gelling strategy is used to combine the guar gum and metal hydroxide, which helps to prepare hollow hierarchical porous hydroxyapatite beads. Results show that the concentration of copper ions and calcination temperature greatly affect the microstructure transformation of the product. Higher concentrations of copper ions lead to the growth of hollow structures, and these ceramic beads exhibit excellent biocompatibility and antibacterial properties. The structure evolution of the products is systematically investigated, and a formation mechanism has been proposed.

Tissue engineered bone mimetics to study bone disorders ex vivo: Role of bioinspired materials

Recent advances in materials development and tissue engineering has resulted in a substantial number of bioinspired materials that recapitulate cardinal features of bone extracellular matrix (ECM) such as dynamic inorganic and organic environment(s), hierarchical organization, and topographical features. Bone mimicking materials, as defined by its self-explanatory term, are developed based on the current understandings of the natural bone ECM during development, remodeling, and fracture repair. Compared to conventional plastic cultures, biomaterials that resemble some aspects of the native environment could elicit a more natural molecular and cellular response relevant to the bone tissue. Although current bioinspired materials are mainly developed to assist tissue repair or engineer bone tissues, such materials could nevertheless be applied to model various skeletal diseases in vitro. This review summarizes the use of bioinspired materials for bone tissue engineering, and their potential to model diseases of bone development and remodeling ex vivo. We largely focus on biomaterials, designed to re-create different aspects of the chemical and physical cues of native bone ECM. Employing these bone-inspired materials and tissue engineered bone surrogates to study bone diseases has tremendous potential and will provide a closer portrayal of disease progression and maintenance, both at the cellular and tissue level. We also briefly touch upon the application of patient-derived stem cells and introduce emerging technologies such as organ-on-chip in disease modeling. Faithful recapitulation of disease pathologies will not only offer novel insights into diseases, but also lead to enabling technologies for drug discovery and new approaches for cell-based therapies.

Construction of a micro/nano structured surface on a β-TCP/CaSiO3 bioceramic promotes osteogenic differentiation of mBMSCs

We report a simple and practical process to construct surface structures with water as the only reagent system; the additive-free system provides regulated structures with few defects and impurities.

The effect of different hydroxyapatite microparticles on the osteogenic differentiation of MC3T3-E1 preosteoblasts

HA microparticles with different sizes and shapes played obvious different roles in promoting the osteogenic differentiation of MC3T3-E1 preosteoblasts. HA microspheres played a better role in promoting the osteogenic differentiation of MC3T3-E1 preosteoblasts than HA whiskers.

Facile fabrication of bioactive ultra-small protein–hydroxyapatite nanoconjugates via liquid-phase laser ablation and their enhanced osteogenic differentiation activity

Ultra-small protein–hydroxyapatite nanoconjugates promote the osteogenic differentiation of mesenchymal stem cells.

Preparation of an antimicrobial surface by direct assembly of antimicrobial peptide with its surface binding activity

The designed antimicrobial peptide has surface binding activity onto titanium, gold, polymethyl methacrylate and hydroxyapatite substrates.

The effects of dissociated rods and rod-surfaced microspheres on bone mesenchymal stem cellular viability

Material properties and cellular behaviours seemed to be coupled, implying the existence of reciprocities between cells and materials.

Nano-hydroxyapatite reinforced polyphenylene sulfide biocomposite with superior cytocompatibility and in vivo osteogenesis as a novel orthopedic implant

The design of novel functional biomaterials that possess similar mechanical attributes as human bones, accompanied with admirable osteogenesis to replace conventional metallic implants would be an intriguing accomplishment.

In vivo comparison of biomineralized scaffold-directed osteogenic differentiation of human embryonic and mesenchymal stem cells

Human pluripotent stem cells such as embryonic stem cells (hESCs) and multipotent stem cells like mesenchymal stem cells (hMSCs) hold great promise as potential cell sources for bone tissue regeneration. Comparing the in vivo osteogenesis of hESCs and hMSCs by biomaterial-based cues provides insight into the differentiation kinetics of these cells as well as their potential to contribute to bone tissue repair in vivo. Here, we compared in vivo osteogenic differentiation of hESCs and hMSCs within osteoinductive calcium phosphate (CaP)-bearing biomineralized scaffolds that recapitulate a bone-specific mineral microenvironment. Both hESCs and hMSCs underwent osteogenic differentiation responding to the biomaterial-based instructive cues. Furthermore, hMSCs underwent earlier in vivo osteogenesis compared to hESCs, but both stem cell types acquired a similar osteogenic maturation by 8 weeks of implantation.

Controlling the strontium-doping in calcium phosphate microcapsules through yeast-regulated biomimetic mineralization

Yeast cells have controllable biosorption on metallic ions during metabolism. However, few studies were dedicated to using yeast-regulated biomimetic mineralization process to control the strontium-doped positions in calcium phosphate microcapsules. In this study, the yeast cells were allowed to pre-adsorb strontium ions metabolically and then served as sacrificing template for the precipitation and calcination of mineral shell. The pre-adsorption enabled the microorganism to enrich of strontium ions into the inner part of the microcapsules, which ensured a slow-release profile of the trace element from the microcapsule. The co-culture with human marrow stromal cells showed that gene expressions of alkaline phosphatase and Collagen-I were promoted. The promotion of osteogenic differentiation was further confirmed in the 3D culture of cell-material complexes. The strategy using living microorganism as 'smart doping apparatus' to control incorporation of trace element into calcium phosphate paved a pathway to new functional materials for hard tissue regeneration.

Surface chemistry from wettability and charge for the control of mesenchymal stem cell fate through self-assembled monolayers

Self-assembled monolayers (SAMs) of alkanethiols on gold are highly controllable model substrates and have been employed to mimic the extracellular matrix for cell-related studies. This study aims to systematically explore how surface chemistry influences the adhesion, morphology, proliferation and osteogenic differentiation of mouse mesenchymal stem cells (mMSCs) using various functional groups (-OEG, -CH₃, -PO₃H₂, -OH, -NH₂ and -COOH). Surface analysis demonstrated that these functional groups produced a wide range of wettability and charge: -OEG (hydrophilic and moderate iso-electric point (IEP)), -CH₃ (strongly hydrophobic and low IEP), -PO₃H₂ (moderate wettability and low IEP), -OH (hydrophilic and moderate IEP), -NH₂ (moderate wettability and high IEP) and -COOH (hydrophilic and low IEP). In terms of cell responses, the effect of wettability may be more influential than charge for these groups. Moreover, compared to -OEG and -CH₃ groups, -PO₃H₂, -OH, -NH₂ and -COOH functionalities tended to promote not only cell adhesion, proliferation and osteogenic differentiation but also the expression of α_v and β₁ integrins. This finding indicates that the surface chemistry may guide mMSC activities through α_v and β₁ integrin signaling pathways. Model surfaces with controllable chemistry may provide insight into biological responses to substrate surfaces that would be useful for the design of biomaterial surfaces.

Defect-Related Luminescent Hydroxyapatite-Enhanced Osteogenic Differentiation of Bone Mesenchymal Stem Cells Via an ATP-Induced cAMP/PKA Pathway

Novel defect-related hydroxyapatite (DHAP), which combines the advantages of HAP and defect-related luminescence, has the potential application in tissue engineering and biomedical area, because of its excellent capability of monitoring the osteogenic differentiation and material biodegradation. Although the extracellular mechanism of DHAP minerals and PO4(3-) functioning in osteogenic differentiation has been widely studied, the intracellular molecular mechanism through which PO4(3-) mediates osteogenesis of bone mesenchymal stem cells (BMSCs) is not clear. We examined a previously unknown molecular mechanism through which PO4(3-) promoted osteogenesis of BMSCs with an emphasis on adenosine-triphosphate (ATP)-induced cAMP/PKA pathway. Our studies showed that DHAP could be uptaken into lysosome, in which PO4(3-) was released from DHAP, because of the acid environment of lysosome. The released PO4(3-) interacted with ADP to form ATP, and then degraded into adenosine, an ATP metabolite, which interacted with A2b adenosine receptor to activate the cAMP/PKA pathway, resulting in the high expression of osteogenesis-related genes, such as Runx2, BMP-2, and OCN. These findings first revealed the function of ATP-metabolism in bone physiological homeostasis, which may be developed to cure bone metabolic diseases.

Comparative Analysis of Proliferation and Viability of Multipotent Mesenchymal Stromal Cells in 3D Scaffolds with Different Architectonics

3D biodegradable materials (scaffolds) containing bioactive hydroxyapatite molecules fabricated by foaming in supercritical carbon dioxide and by selective laser sintering were used for culturing of mesenchymal stromal cells from the human adipose tissue. Experiments showed that stromal cells from the human adipose tissue adhered and proliferated on all studied types of structures. Addition of hyproxyapatite to the scaffold stimulated proliferation of stromal adipose tissue cells.

Microfluidic generation of magnetic-fluorescent Janus microparticles for biomolecular detection

Fluorescent magnetic multifunctional microparticles were fabricated by a facile droplet microfluidic strategy. Two sodium alginate streams, one doped with Fe3O4 nanoparticles (NPs) and the other with CdSe/ZnS quantum dots, were introduced into a flow-focusing channel as a type of parallel laminar flow to form droplets containing two distinct parts. Then, at the serpentine channel, the Ca(2+) in the oil phase diffused into the droplets, causing the solidification of the droplets. Thus, the Janus microparticles with excellent magnetic/fluorescent properties formed. The flow conditions were optimized and the effects of the flow rates on magnetic/fluorescent compositions were carefully investigated. Luminescent labeling and magnetic separation were simultaneously realized with the newly designed microparticles. Moreover, spatial separation between Fe3O4 NPs and QDs prevented the interference of QDs photoluminescence by the magnetic particles. The as-prepared fluorescent magnetic Janus particles were also successfully employed for DNA assay, which demonstrated the potential of the multifunctional microbeads in biological applications.

Immobilization of cadmium ions to synthesis hierarchical flowerlike cadmium phosphates microspheres and their application in the degradation of organic pollutants under light irradiation

Hierarchical flowerlike Cd₅H₂(PO₄)₄·4H₂O and Cd₅(PO₄)₂P₂O₇ microspheres were prepared by cadmium ion immobilization followed by an annealing treatment. Cd₅(PO₄)₂P₂O₇ was applied as a novel photocatalyst toward dye degradation under light irradiation.