The selection of a nitrogen precursor for the construction of N-doped titanium dioxide with enhanced photocatalytic activity for the removal of gaseous toluene

The preparation of nitrogen-doped TiO2 (i.e., N-TiO2) catalysts is a highly effective option to improve the photocatalytic activity of TiO2. Nonetheless, relatively little is known about the effects of dopant precursors selected for their preparation with regard to the photocatalytic efficacy. In this study, three types of dopants are selected and used as N sources (urea (U), melamine (M), and aqueous ammonia (A)) for N-TiO2 samples with the name codes of NTU, NTM, and NTA, respectively. The photocatalytic efficacy of these N-TiO2 samples is examined against toluene in a packed bed flow reactor. Under optimal conditions (e.g., relative humidity (RH) = 20% and gas hourly space velocity (GHSV) = 1698 h-1), the superiority of NTA is evident over others with a quantum efficiency (QE) of 7.03 × 10-4 molecules photon-1, a space time yield (STY) of 1.38 × 10-4 molecules photon-1 mg-1, and a specific clean air delivery rate (SCADR) of 1148.8 L g-1 h-1. The analysis based on in-situ diffuse reflectance infrared Fourier transform spectroscopy and gas chromatography-mass spectrometry confirms the formation of several intermediates such as benzyl alcohol, benzaldehyde, benzoic acid, and alkane species through ring opening reactions. In addition, the prepared NTA photocatalyst exhibits the highest toluene photocatalytic degradation efficiency among all TiO2-based catalysts surveyed to date. Overall, this study offers as a valuable guideline for the development of advanced TiO2 catalytic systems (such as N-TiO2) for the treatment of aromatic hydrocarbons in indoor air.

Molybdenum sulfide modified with nickel or platinum nanoparticles as an effective catalyst for hydrogen evolution reaction

In this study, we investigate the catalytic performance of molybdenum sulfide (MoS2) modified with either nickel (Ni) or platinum (Pt) nanoparticles as catalysts for the hydrogen evolution reaction (HER). The MoS2 was prepared on the TiO2 nanotube substrates via a facile hydrothermal method, followed by the deposition by magnetron sputtering of Ni or Pt nanoparticles on the MoS2 surface. Structural and morphological characterization confirmed the successful incorporation of Ni or Pt nanoparticles onto the MoS2 support. Electrochemical measurements revealed that Ni- and Pt-modified MoS2 catalysts exhibited enhanced HER activity compared to pristine MoS2. Obtained catalysts demonstrated a low onset potential, reduced overpotential, and increased current density, indicating efficient electrocatalytic performance. Furthermore, the Ni or Pt-modified MoS2 catalyst exhibited remarkable stability during prolonged HER operation. The improved catalytic activity can be attributed to the synergistic effect between metal nanoparticles and MoS2, facilitating charge transfer kinetics and promoting hydrogen adsorption and desorption. Incorporating Ni and Pt nanoparticles also provided additional active sites on the MoS2 surface, enhancing the catalytic activity.

TiO2/PDA Multilayer Nanocomposites with Exceptionally Sharp Large-Scale Interfaces and Nitrogen Doping Gradient

The evolving field of photocatalysis requires the development of new functional materials, particularly those suitable for large-scale commercial systems. One particularly promising approach is the creation of hybrid organic/inorganic materials. Despite being extensively studied, materials such as polydopamine (PDA) and titanium oxide continue to show significant promise for use in such applications. Nitrogen-doped titanium oxide and free-standing PDA films obtained at the air/water interface are particularly interesting. This study introduces a straightforward and reproducible approach for synthesizing a novel class of large-scale multilayer nanocomposites. The method involves the alternate layering of high-quality materials at the air/water interface combined with precise atomic layer deposition techniques, resulting in a gradient nitrogen doping of titanium oxide layers with exceptionally sharp oxide/polymer interfaces. The analysis confirmed the presence of nitrogen in the interstitial and substitutional sites of the TiO2 lattice while maintaining the 2D-like structure of the PDA films. These chemical and structural characteristics translate into a reduction of the band gap by over 0.63 eV and an increase in the photogenerated current by over 60% compared with pure amorphous TiO2. Furthermore, the nanocomposites demonstrate excellent stability during the 1 h continuous photocurrent generation test.

Pyridinic nitrogen dominated doping on Pd/carbon catalysts for enhanced hydrogenation performance

The hydrogenation of 4-carboxylbenzaldehyde over Pd catalysts is a crucial process during the production of pure terephthalic acid. Herein, ZIF-8 derived carbon materials (NC) with adjustable N types were synthesized and used as the supports of Pd catalysts. Pd supported on NC with 50.5% of pyridinic N exhibited best hydrogenation activity with a TOF value of 4.1 min-1. The microstructures of NC support and electronic structures of Pd in Pd/NC were investigated by techniques such as XRD, N2 physisorption, XPS, H2-O2 titration and TEM. The nitrogen species in CN surface not only can adjust chemical state and dispersion of Pd nanoparticles (NPs), but also promote the adsorption and activation capability of H2 molecular. Besides, the ratio of Pd0/Pd2+ and Pd dispersion were closely correlated with pyridinic nitrogen content. The improvement in hydrogenation activity and stability of Pd/CN catalyst in relative to Pd/C were ascribed to the synergistic effect of pyridinic nitrogen and active site Pd0.

Single-step fabrication of highly stable amorphous TiO2 nanotubes arrays (am-TNTA) for stimulating gas-phase photoreduction of CO2 to methane

This study investigates the facile fabrication of interfacial defects assisted amorphous TiO₂ nanotubes arrays (am-TNTA) for promoting gas-phase CO₂ photoreduction to methane. The am-TNTA catalyst was fabricated via a one-step synthesis, without heat treatment, by anodization of Titanium in Ethylene glycol-based electrolyte in a shorter anodizing time. The samples presented a TiO₂ nanostructured array with a nanotubular diameter of 100 ± 10 nm, a wall thickness of 26 ± 5 nm, and length of 3.7 ± 0.3 μm, resulting in a specific surface of 0.75 m² g. The am-TNTA presented prolonged chemical stability, a high exposed surface area, and a large number of surface traps that can reduce the recombination of the charge carriers. The am-TNTA showed promising photoactivity when tested in the CO₂ reduction reaction with water under UV irradiation with a methane production rate of 14.0 μmol g_cat^-1 h^-1 for a pure TiO₂ material without any modification procedure. This enhanced photocatalytic activity can be explained in terms of surface defects of the amorphous structure, mainly OH groups that can act as electron traps for increasing the electron lifetime. The CO₂ interacts directly with those traps, forming carbonate species, which favors the catalytic conversion to methane. The am-TNTA also exhibited a high stability during six reaction cycles. The photocatalytic activity, the significantly reduced time for synthesis, and high stability for continuous CH₄ production make this nanomaterial a potential candidate for a sustainable CO₂ reduction process and can be employed for other energy applications.

A simple and efficient ultrasonic-assisted electrochemical approach for scalable production of nitrogen-doped TiO2nanocrystals

In this study, we report a facile and effective approach for large-scale production of nitrogen-doped TiO₂nanocrystals (UNTs) by a combination of ultrasonic irradiation and electrochemistry at room temperature using NH₄NO₃electrolyte as the nitrogen source. The as-prepared UNTs were then characterized by x-ray diffraction, Raman spectroscopy, x-ray photoelectron spectroscopy, scanning electron microscopy, transmission electron microscopy, and UV-visible diffuse reflectance spectroscopy. The results indicated that the nitrogen content of UNTs reached 9.3% and bandgap energy of 2.62 eV, thus gave the high photocatalytic degradation of methylene blue under visible light irradiation. The mechanism for the formation of UNTs by ultrasonic-assisted electrochemical approach was also proposed.

C-,N- and S-Doped TiO2 Photocatalysts: A Review

This article presents an overview of the reports on the doping of TiO2 with carbon, nitrogen, and sulfur, including single, co-, and tri-doping. A comparison of the properties of the photocatalysts synthesized from various precursors of TiO2 and C, N, or S dopants is summarized. Selected methods of synthesis of the non-metal doped TiO2 are also described. Furthermore, the influence of the preparation conditions on the doping mode (interstitial or substitutional) with reference to various types of the modified TiO2 is summarized. The mechanisms of photocatalysis for the different modes of the non-metal doping are also discussed. Moreover, selected applications of the non-metal doped TiO2 photocatalysts are shown, including the removal of organic compounds from water/wastewater, air purification, production of hydrogen, lithium storage, inactivation of bacteria, or carbon dioxide reduction.

Optimization of N doping in TiO2 nanotubes for the enhanced solar light mediated photocatalytic H2 production and dye degradation

Herein, we report the optimization of nitrogen (N) doping in TiO₂ nanotubes to achieve the enhanced photocatalytic efficiencies in degradation of dye and H₂ gas evolution under solar light exposure. TiO₂ nanotubes have been produced via hydrothermal process and N doping has been tuned by varying the concentration of urea, being the source for N, by solid-state dispersion process. The structural analysis using XRD showed the characteristic occupancy of N into the structure of TiO₂ and the XPS studies showed the existence of Ti-N-Ti network in the N-doped TiO₂ nanotubes. The obtained TEM images showed the formation of 1D tube-like structure of TiO₂. Diffuse reflectance UV-Vis absorption spectra demonstrated that the N-doped TiO₂ nanotubes can efficiently absorb the photons of UV-Vis light of the solar light. The optimized N-doped TiO₂ nanotubes (TiO₂ nanotubes vs urea @ 1:1 ratio) showed the highest degradation efficiency over methyl orange dye (∼91% in 90 min) and showed the highest rate of H₂ evolution (∼19,848 μmol h^-1.g^-1) under solar light irradiation. Further, the recyclability studies indicated the excellent stability of the photocatalyst for the durable use in both the photocatalytic processes. The observed efficiency was ascribed to the optimized doping of N-atoms into the lattices of TiO₂, which enhanced the optical properties by forming new energy levels of N atoms near the valence band maximum of TiO₂, thereby increased the overall charge separation and recombination resistance in the system. The improved reusability of photocatalyst is attributed to the doping-induced structural stability in N-doped TiO₂. From the observed results, it has been recognized that the established strategy could be promising for synthesizing N-doped TiO₂ nanotubes with favorable structural, optical and photocatalytic properties towards dye degradation and hydrogen production applications.

Plasma Nitriding of TiO2 Nanotubes: N-Doping in Situ Investigations Using XPS

The nitrogen doping of titanium dioxide nanotubes (TiO₂ NTs) was investigated as a result of well-controlled plasma nitriding of TiO₂ NTs at a low temperature. This way of nitrogen doping is proposed as an alternative to chemical/electrochemical methods. The plasma nitriding process was performed in a preparation chamber connected to an X-ray photoelectron spectroscopy (XPS) spectrometer, and the nitrogen-doped TiO₂ NTs were next investigated in situ by XPS in the same ultrahigh vacuum (UHV) system. The collected high-resolution (HR) XPS spectra of N 1s, Ti 2p, O 1s, C 1s, and valence band (VB) revealed the formation of chemical bonds between titanium, nitrogen, and oxygen atoms as substitutional or interstitial species. Moreover, the results provided a characterization of the electronic states of N-TiO₂ NTs generated by various plasma nitriding and annealing treatments. The VB XPS spectrum showed a reduction in the TiO₂ band gap of about 0.6 eV for optimal nitriding and heat-treated conditions. The TiO₂ NTs annealed at 450 or 650 °C in air (ex situ) and nitrided under UHV conditions were used as reference materials to check the formation of Ti-N bonds in the TiO₂ lattice with a well-defined structure (anatase or a mixture of anatase and rutile). Scanning electron microscopy microscopic observations of the received materials were used to evaluate the morphology of the TiO₂ NTs after each step of the nitriding and annealing treatments.

Single step synthesis of Schottky-like hybrid graphene - titania interfaces for efficient photocatalysis

The development of 2D nanomaterial coatings across metal surfaces is a challenge due to the mismatch between the metal microstructure and the nanoscale materials. The naturally occurring thin oxidative layer present across all metal surfaces, may lead to low adherence and connectivity. In this paper, graphene/titania/Titanium hybrid films were for the first time fabricated by a single step chemical vapour deposition process across Titanium foils. The presence of graphene as a dopant was found to enhance the photocatalytic performance of the final products, applied to the degradation of organic molecules and to lead to Schottky-like junction formation at the metal/oxide interface. These Schottky junctions, where vacancies are present across the titania material due to the graphene doping and where Ti³⁺ ions are predominantly located, yield enhanced catalytic performance. The highest degradation rate was found to be 9.66 × 10⁻⁶ min⁻¹, achieved by the sample grown at 700 °C for 5 min, which was 62% higher than the sample just treated at that temperature without graphene growth. This work provides evidence that graphene may be grown across pure Titanium metal and opens new avenues in biomedical devices design, tribological or separation applications.

Nitrogen-doped titanium dioxide (N-doped TiO2) for visible light photocatalysis

Energy level diagrams for undoped and N-doped TiO₂ for visible light induced photocatalytic application.

Titania nanotubes infiltrated with the conducting polymer PEDOT modified by Prussian blue – a novel type of organic–inorganic heterojunction characterised with enhanced photoactivity

A highly ordered p–n heterojunction was formed based on titania nanotubes containing a conducting polymer with Prussian blue matrix.

Highly stable organic–inorganic junction composed of hydrogenated titania nanotubes infiltrated by a conducting polymer

A poly(3,4-ethylenedioxythiophene) conducting polymer doped with poly(2-styrene sulfonate) (pEDOT:PSS) was efficiently electrodeposited on a layer composed of ordered titania nanotubes.

Gas-generated thermal oxidation of a coordination cluster for an anion-doped mesoporous metal oxide

Central in material design of metal oxides is the increase of surface area and control of intrinsic electronic and optical properties, because of potential applications for energy storage, photocatalysis and photovoltaics. Here, we disclose a facile method, inspired by geochemical process, which gives rise to mesoporous anion-doped metal oxides. As a model system, we demonstrate that simple calcination of a multinuclear coordination cluster results in synchronic chemical reactions: thermal oxidation of Ti₈O₁₀(4-aminobenzoate)₁₂ and generation of gases including amino-group fragments. The gas generation during the thermal oxidation of Ti₈O₁₀(4-aminobenzoate)₁₂ creates mesoporosity in TiO₂. Concurrently, nitrogen atoms contained in the gases are doped into TiO₂, thus leading to the formation of mesoporous N-doped TiO₂. The mesoporous N-doped TiO₂ can be easily synthesized by calcination of the multinuclear coordination cluster, but shows better photocatalytic activity than the one prepared by a conventional sol-gel method. Owing to an intrinsic designability of coordination compounds, this facile synthetic will be applicable to a wide range of metal oxides and anion dopants.

Enhanced photoelectrochemical and photocatalytic performance of iodine-doped titania nanotube arrays

The paper discusses the synthesis and performance of iodine doped titania nanotube arrays exhibited under irradiation.