A sweet spot for highly efficient growth of vertically aligned single-walled carbon nanotube forests enabling their unique structures and properties

A Hydrogen-Free Approach for Activating an Fe Catalyst Using Trace Amounts of Noble Metals and Confinement into Nanoparticles

Metallic iron (Fe) represents an exceptionally active catalyst, as shown in its use in the Haber-Bosch process to dissociate nitrogen molecules; however, the ease of corrosion by oxidation limits its usage. Hence, in most applications using metallic Fe catalysts, hydrogen is a necessary reactant. We report a novel hydrogen-free approach to fabricating reduced, highly active, and corrosion-resistive Fe-based catalysts using trace levels of noble metals (NMs) such as Ir, Rh, and Pt confined in the nanoparticle (NP). X-ray photoelectron spectroscopy (XPS) revealed that as little as ∼0.3 atom % was sufficient to induce the reduction of Fe. Extensive XPS analysis showed that the reduced NM atoms segregated to the NP surface and reduced the surrounding Fe atoms. We demonstrated the catalytic activity of the nanoparticles by the efficient synthesis of submillimeter tall, vertically aligned, and mainly double-walled carbon nanotube arrays using a completely hydrogen-free chemical vapor deposition process.

Semiconductor nanochannels in metallic carbon nanotubes by thermomechanical chirality alteration

[Figure: see text].

Quantitative Evidence for the Dependence of Highly Crystalline Single Wall Carbon Nanotube Synthesis on the Growth Method

We present a study quantitatively demonstrating that the method of synthesis (gas phase, fixed bed, non-fixed bed) represents a determining factor in the level of crystallinity in growing single wall carbon nanotubes (SWCNTs). Using far infrared spectroscopy, the "effective length" (associated with the level of crystallinity) was estimated for CNTs grown using various synthetic methods (lab-produced and supplemented by commercially purchased SWCNTs) as a metric for crystallinity (i.e., defect density). Analysis of the observed "effective lengths" showed that the SWCNTs fell into two general groups: long and short (high and low crystallinity) synthesized by gas-phase methods and all other supported catalyst methods, respectively. Importantly, the "long" group exhibited effective lengths in the range of 700-2200 nm, which was greater than double that of the typical values representing the "short" group (110-490 nm). These results highlight the significant difference in crystallinity. We interpret that the difference in the crystallinity stemmed from stress concentration at the nanotube-catalyst interface during the growth process, which originated from various sources of mismatch in growth rates (e.g., vertically aligned array) as well as impact stress from contact with other substrates during fluidization or rotation. These results are consistent with well-accepted belief, but now are demonstrated quantitatively.

Low frequency vibrations observed on assemblies of vertical multiwall carbon nanotubes by Brillouin light scattering: determination of the Young modulus

Assemblies of vertical multiwall carbon nanotubes, (VCNTs), have been synthesized by coupling dewetting of cobalt or nickel ultrathin layers and plasma enhanced chemical vapor deposition. Electronic microscopies revealed well defined micrometer length nanotubes with inner radius of 3-4 nm and outer radius of 8-9 nm. Similar structural qualities have been revealed by Raman measurements. Dynamic behaviour of these VCNTs assemblies have been studied by means of Brillouin light scattering technique. The measured inelastic light scattering from VCNTs is attributed to bending vibrations of the nanotubes. The observed frequencies on both assemblies, considered as dense effective media, are compatible with an effective Young modulus of 850 GPa.

Additional obstacles in carbon nanotube growth by gas-flow directed chemical vapour deposition unveiled through improving growth density

Here, we demonstrate an approach of increasing the density of ultralong carbon nanotube (CNT) growth by combining a fast-heating method developed by Huang et al. (J. Am. Chem. Soc., 2003, 125, 5636-5637) with catalyst support engineering. Specifically, using graphene oxide as a catalyst support for iron oxide (Fe3O4) catalyst nanoparticles, we achieved high density growth of CNTs grown by the "kite-mechanism". Our analysis revealed that the fast-heating method reduced undesired aggregation of the catalyst nanoparticles, which has been reported to be a primary limitation mechanism, by shortening the time between substrate heating and CNT growth. In addition, the use of the graphene oxide support led to controllable and uniform dispersion of catalyst nanoparticles in relatively high density which provided increased process control by extending the time before the onset of catalyst aggregation. Together, these approaches suppressed the aggregation of the catalyst nanoparticles, which facilitated the "tip-growth" mode instead of the "root-growth" mode, and led to the high density growth of ultralong CNTs. Our results also indicate additional limitations and complexities on the high density CNT growth by the kite-growth approach, which limit high density synthesis.

Flame-Synthesis of Carbon Nanotube Forests on Metal Mesh Structure: Dependence, Morphology, and Application

Multi-walled carbon nanotubes (MWCNTs) in the form of “forests” were synthesized directly on the surface of stainless steel (SS) mesh from ethanol flame volume. The growth dependence of the MWCNT forests on the porosity of SS mesh substrate and the morphologies and growth mechanism of the MWCNT forests were investigated in detail by a combination of turbulent flow simulation, scanning electron microscopy (SEM), transmission electron microscope (TEM), and Raman and X-ray diffraction (XRD) spectroscopy. The growth height of the MWCNT forests exhibited a strong dependence on the flame gas flow rate controlled by the porosity of SS mesh substrate, and the maximum averaged height of the MWCNT forests reached 34 μm. Most MWCNTs grew perpendicularly on the surface of SS wires, and some branch, welded, and spiral structures were observed by SEM and TEM. The MWCNT-decorated mesh was used as a novel heating element to weld glass-fabric-reinforced polyetherimide (GF/PEI) thermoplastics. We found that the maximum tensile lap-shear strength (LSS) of the welded joints could reach 39.21 MPa, an increase of 41% in comparison with that of conventional SS mesh-based joints.

High surface-area carbon microcantilevers

Microscale porous carbon mechanical resonators were formed using carbon nanotube templated microfabrication. These cantilever resonators exhibited nanoscale porosity resulting in a high surface area to volume ratio which could enable sensitive analyte detection in air. These resonators were shown to be mechanically robust and the porosity could be controllably varied resulting in densities from 10² to 10³ kg m^-3, with pore diameters on the order of hundreds of nanometers. Cantilevers with lengths ranging from 500 μm to 5 mm were clamped in a fixture for mechanical resonance testing where quality factors from 10² to 10³ were observed at atmospheric pressure in air.

Carbon Nanotubes and Related Nanomaterials: Critical Advances and Challenges for Synthesis toward Mainstream Commercial Applications

Advances in the synthesis and scalable manufacturing of single-walled carbon nanotubes (SWCNTs) remain critical to realizing many important commercial applications. Here we review recent breakthroughs in the synthesis of SWCNTs and highlight key ongoing research areas and challenges. A few key applications that capitalize on the properties of SWCNTs are also reviewed with respect to the recent synthesis breakthroughs and ways in which synthesis science can enable advances in these applications. While the primary focus of this review is on the science framework of SWCNT growth, we draw connections to mechanisms underlying the synthesis of other 1D and 2D materials such as boron nitride nanotubes and graphene.

The double-edged effects of annealing MgO underlayers on the efficient synthesis of single-wall carbon nanotube forests

Recently, the millimetre-scale, highly efficient synthesis of single-wall carbon nanotube (SWCNT) forests from Fe catalysts has been reported through the annealing of the magnesia (MgO) underlayer. Here, we report the double-edged effects of underlayer annealing on the efficiency and structure of the SWCNT forest synthesis through a temperature-dependent examination. Our results showed that the efficiency of the SWCNT forests sharply increased with increased underlayer annealing temperatures from 600 °C up to 900 °C due to a temperature-dependent structural modification, characterized by increased grain size and reduced defects, of the MgO underlayer. Beyond this temperature, the SWCNT fraction also decreased as a result of further structural modification of the MgO underlayer. This exemplifies the double-edged effects of annealing. Specifically, for underlayer annealing below 600 °C, the catalyst subsurface diffusion was found to limit the growth efficiency, and for excessively high underlayer annealing temperatures (>900 °C), catalyst coalescence/ripening led to the formation of double-wall carbon nanotubes. As a result, three distinct regions of synthesis were observed: (i) a "low yield" region below a threshold temperature (∼600 °C); (ii) an "increased yield" region from 600 to 900 °C, and (iii) a "saturation" region above 900 °C. The efficient SWCNT forest synthesis could only occur within a specific annealing temperature window as a result of this double-edged effects of underlayer annealing.

Vertically Aligned Carbon Nanotubes as Platform for Biomimetically Inspired Mechanical Sensing, Bioactive Surfaces, and Electrical Cell Interfacing

Vertically aligned carbon nanotubes (VACNTs) are one dimensional carbon objects anchored atop of a solid substrate. They are geometrically fixed in contrast to their counterparts, randomly oriented carbon nanotubes (CNTs). In this progress report, the breadth in which these one dimensional, mechanically flexible, though robust and electrical conducting carbon nanostructures can be employed as functional material is shown and our research is put in perspective to work in the last five to ten years. The connection between the different areas touched in this report is the biomimetic-materials approach, which rely on the hairy morphology of VACNTs. These properties in connection with their electrical conductivity offer possibilities towards new functional features and applications of VACNTs. To appreciate the possibilities of biomimetic research with VACNTs, first their material characteristics are given to make the reader familiar with specific features of their synthesis, the peculiarities in arranging and controlling the morphology of CNTs in a vertical alignment as well as a current understanding of these properties on a microscopic basis. In doing so, similarities as well as differences, which offer new possibilities for biomimetic studies of VACNTS with respect to multiwalled randomly oriented CNTs, will become clear.

Aqueous dispersion of single walled carbon nanotubes stabilized by PEG modified diperylene bisimide and their application as an antibacterial agent

Polyethylene glycol modified diperylene bisimide was synthesized and applied to disperse single-walled carbon nanotubes in water. Moreover, the well-dispersed SWCNTs show excellent antibacterial activities.