Influence of carbon and graphene oxide nanoparticle on the adhesive properties of dentin bonding polymer: A SEM, EDX, FTIR study

OBJECTIVE

This study was aimed at including 2.5 wt.% of carbon nanoparticles (CNPs) and graphene oxide NPs (GNPs) in a control adhesive (CA) and then investigate the effect of this inclusion on their mechanical properties and its adhesion to root dentin.

MATERIALS AND METHODS

Scanning electron microscopy and energy dispersive X-ray (SEM-EDX) mapping were conducted to investigate the structural features and elemental distribution of CNPs and GNPs, respectively. These NPs were further characterized by Raman spectroscopy. The adhesives were characterized by evaluating their push-out bond strength (PBS), rheological properties, degree of conversion (DC) investigation, and failure type analysis.

RESULTS

The SEM micrographs revealed that the CNPs were irregular and hexagonal, whereas the GNPs were flake-shaped. EDX analysis showed that carbon (C), oxygen (O), and zirconia (Zr) were found in the CNPs, while the GNPs were composed of C and O. The Raman spectra for CNPs and GNPs revealed their characteristic bands (CNPs-D band: 1334 cm-1, GNPs-D band: 1341 cm-1, CNPs-G band: 1650 cm-1, and GNPs-G band: 1607 cm-1). The testing verified that the highest bond strength to root dentin were detected for GNP-reinforced adhesive (33.20 ± 3.55 MPa), trailed closely by CNP-reinforced adhesive (30.48 ± 3.10 MPa), while, the CA displayed lowest values (25.11 ± 3.60 MPa). The inter-group comparisons of the NP-reinforced adhesives with the CA revealed statistically significant results (p < 0.01). Failures of adhesive nature were most common in within the adhesives and root dentin. The rheological assessment results demonstrated a reduced viscosity for all the adhesives observed at advanced angular frequencies. All the adhesives verified suitable dentin interaction shown by hybrid layer and appropriate resin tag development. A reduced DC was perceived for both NP-reinforced adhesives, compared to the CA.

CONCLUSION

The present study's findings have demonstrated that 2.5% GNP adhesive revealed the highest, suitable root dentin interaction, and acceptable rheological properties. Nevertheless, a reduced DC was observed (matched with the CA). Prospective studies probing the influence of diverse concentrations of filler NPs on the adhesive's mechanical properties to root dentin are recommended.

Operando spectroelectrochemistry of bulk-exfoliated 2D SnS2 for anodes within alkali metal ion batteries reveals unusual tin (III) states

In this study we report an affordable synthesis and preparation of an electrochemically exfoliated few-layer 2-dimensional (2D) SnS2 anode material of high cycling durability and demonstrate its performance on the example of alkali metal batteries. The metalation mechanism consists of highly unusual and previously only speculated Sn (III)-state grasped by operando Raman spectroelectrochemistry aided by symmetry analysis. The prepared 2D material flakes were characterized by high resolution transmission electron microscopy, X-ray photoelectron and Raman spectroscopies. The operando Raman spectroelectrochemistry was chosen as a dedicated tool for the investigation of alkali-metal-ion intercalation (Li, Na, K), whereby the distortion of the A1g Raman active mode (out-of-plane S-Sn-S vibration) during battery charging exhibited a substantial dependence on the electrochemically applied potential. As a result of the structural dynamics a considerable Raman red-shift of 17.6 cm−1 was observed during metalation. Linewidth changes were used to evaluate the expansion caused by metalation, which in case of sodium and potassium were found to be minimal compared to lithium. Based on the spectroscopic and electrochemical results, a mechanism for the de-/intercalation of lithium, sodium and potassium is proposed which includes alloying in few-layer 2D SnS2 materials and the generation of point-defects.

Graphene oxide enhances thermal stability and microwave absorption/regeneration of a porous polymer

Microwave regeneration of adsorbents offers several advantages over conventional regeneration methods; however, its application for microwave transparent adsorbents such as polymers is challenging. In this study, hypercrosslinked polymer/graphene oxide (GO) nanocomposites with large surface area and enhanced microwave absorption ability were synthesized. Polymers of 4, 4´-bis ((chloromethyl)-1, 1´-biphenyl- benzyl chloride) were hypercrosslinked through the Friedel-Crafts reactions. GO sheets were synthesized through the Hummer's method. Nanocomposites with different GO contents (1-8 wt%) were synthesized by solution mixing method. Thermogravimetry analysis revealed a large enhancement in the thermal stability of GO-filled nanocomposites compared to pristine polymer. N₂ adsorption isotherm analysis showed 7% and 10% reduction in BET surface area and total pore volume of the nanocomposite with 8 wt% GO. Compared to the pristine polymer, the dielectric constant and dielectric loss factor increased from 5 to 17 and 0.05-1.6, respectively, for the nanocomposites with 8 wt% GO. Microwave-assisted desorption of toluene from samples revealed more than 160 ºC and 4 times improvement in the desorption temperature and desorption efficiency, respectively, by addition of 4 wt% GO to the polymer. This study showed the important role of GO addition for efficient microwave-assisted regeneration of polymer adsorbents.

Khalil A, M. Azzouz I. Graphene Functionalization towards Developing Superior Supercapacitors Performance

Graphene is known as the miracle material of the 21st century for the wide band of participating applications and epic properties. Unlike the CVD monolayer graphene, Reduced graphene oxide (RGO) is a commercial form with mass production accessibility via numerous numbers of methods in preparation and reduction terms. Such RGO form showed exceptional combability in supercapacitors (SCs) where RGO is participated to promote flexibility, lifetime and performance. The chapter will illustrate 4 critical milestones of using graphene derivatives for achieving SC’s superior performance. The first is using oxidized graphene (GO) blind with polymer for super dielectric spacer. The other three types are dealing with electrolytic SCs based on RGO. Polyaniline (PANI) was grown on GO for exceptionally stable SCs of 100% retention. Silver decoration of RGO was used for all-solid-state printable device. The solid-state gel electrolyte was developed by adding GO to promote current rating. Finally, laser reduced graphene is presented as a one-step and versatile technique for micropatterning processing. The RGO reduction was demonstrated from a laser GO interaction perspective according to two selected key parameters; wavelength and pulse duration.

Structure, morphology and modelling studies of polyvinylalcohol nanocomposites reinforced with nickel oxide nanoparticles and graphene quantum dots

Nickel oxide (NiO) nanoparticles (NPs) and graphene quantum dots (GQDs) reinforced polyvinyl alcohol (PVA) nanocomposite films were prepared using a solution casting technique. The physicochemical characteristics of PVA/NiO/GQDs (PNG) nanocomposite films were studied using Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), thermogravimetric analysis (TGA), and field emission scanning electron microscopy (FESEM). The obtained PNG nanocomposite films showed good mechanical flexibility and improved tensile strength. The influence of nanofiller concentrations on PNG nanocomposite film. The obtained results demonstrate an increase in the activation energy (Ea) up to PNG3 upon increasing the GQDs concentration and thereafter, its decreases. The fundamental interactions of the constituents of PNG nanocomposite film were investigated using density functional theory (DFT). This study on electronic structure reveals that the PVA model indirectly interacts with GQDs through the NiO model. This configuration is favoured in terms of interaction energy (-78 kJ/mol) compared to the one in which PVA interacts directly with the GQDs model.

Slow-release lubrication of artificial joints using self-healing polyvinyl alcohol/polyethylene glycol/ graphene oxide hydrogel

New fabrication methods and lubrication materials must be developed to improve the lubrication performance of artificial joints and increase the lubrication duration. Herein, a novel polyvinyl alcohol/polyethylene glycol/graphene oxide (PVA/PEG/GO) hydrogel was prepared by a physical cross-linking method, and then the hydrogel and its sustained-release solution were used as lubricant for friction evaluation. The results demonstrated that the slow-release gel solution has good lubrication performance, and coefficient of friction (COF) is only 0.04, which is much lower than the COF of distilled water (about 0.08) under the same conditions. The structure characterization results revealed that no new materials are formed in the gel. The results of thermogravimetric analyses and differential scanning calorimetry demonstrated that the addition of GO may improve the network crosslinking structure of the PVA/PEG hydrogel and improve its mechanical strength. In addition, PVA/PEG/GO hydrogel has superior self-healing function. The self-healing hydrogel did not break again after being pulled under 200 G of weights. The PVA/PEG/GO hydrogel with excellent slow-release lubricating performance and self-healing properties provides a novel candidate for design of long-term lubricating artificial joints, and is expected to promote the progress of artificial joint lubrication applications.

Impact of graphene oxide and silver diamine fluoride in comparison to photodynamic therapy on bond integrity and microleakage scores of resin modified glass ionomer cement to demineralized dentin

AIM

To evaluate the impact of graphene oxide (GO) and silver diammine fluoride (SDF) in comparison to photodynamic therapy (PDT) on adhesive bond integrity and microleakage scores of resin-modified glass ionomer cement (RMGIC) to demineralized dentin.

METHODS

80 non-carious and atraumatic third molars were mounted inside the segments of polyvinyl pipes. Exposure, homogenization, and polishing of dentinal tubules was performed. 20 specimens were left unconditioned and classified a group 4. Exposure of acetic acid was done to 60 specimens and randomly allocated into 3 groups. Group 1 specimens were treated with 0.25 % GO; group 2 specimens were treated with 3.8 % SDF; and group 3 specimens were exposed to PDT. The bonding of all samples to RMGIC was performed by light curing and universal testing machine was utilized for testing shear bond strength (SBS). For failure modes, an optical microscope at 40x magnification was used to observe the debonded interfaces. For microleakage, all the specimens were submerged in 2% methylene blue for 1 day and observed under a digital microscope. The post hoc Tukey and analysis of variance (ANOVA) were used to examine SBS. A p-value of ≤0.05 was considered statistically significant.

RESULTS

Group 2 showed the highest bond strength (3.8 % SDF + RMGIC + DD - 15.27 ± 2.19 MPa). Groups 1 (0.25 % GO + RMGIC + DD - 14.11 ± 3.82) and 2 showed comparable results of SBS, which was significantly higher when compared with other research groups (p < 0.05). According to the post hoc Tukey test, the SBS scores of treatment groups exhibited statistically significant values as compared to the control group (p < 0.05). Group 2 samples showed the least microleakage mean score (0.8 ± 0.42), followed by group 1 specimens (1.02 ± 0.88). The comparable microleakage mean scores were demonstrated by the samples in group 1 and 2 (p < 0.01). According to one-way ANOVA, a significant difference was observed in microleakage scores among experimental groups (p < 0.01).

CONCLUSION

Improved bond strength and marginal microleakage scores were demonstrated by the demineralized dentin treated with 0.25 % graphene oxide and 3.8 % silver diamine fluoride when bonded to resin-modified glass ionomer cement. The application of methylene blue photosensitizer for photodynamic therapy undermined the adhesive bond strength applied on demineralized dentin.

Dentin Bond Integrity of Hydroxyapatite Containing Resin Adhesive Enhanced with Graphene Oxide Nano-Particles-An SEM, EDX, Micro-Raman, and Microtensile Bond Strength Study

The aim was to synthesize and characterize an adhesive incorporating HA and GO nanoparticles. Techniques including scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX), micro-tensile bond strength (μTBS), and micro-Raman spectroscopy were employed to investigate bond durability, presence of nanoparticles inside adhesive, and dentin interaction. Control experimental adhesive (CEA) was synthesized with 5 wt% HA. GO particles were fabricated and added to CEA at 0.5 wt% (HA-GO-0.5%) and 2 wt% GO (HA-GO-2%). Teeth were prepared to produce bonded specimens using the three adhesive bonding agents for assessment of μTBS, with and without thermocycling (TC). The adhesives were applied twice on the dentin with a micro-brush followed by air thinning and photo-polymerization. The HA and GO nanoparticles demonstrated uniform dispersion inside adhesive. Resin tags with varying depths were observed on SEM micrographs. The EDX mapping revealed the presence of carbon (C), calcium (Ca), and phosphorus (P) in the two GO adhesives. For both TC and NTC samples, HA-GO-2% had higher μTBS and durability, followed by HA-GO-0.5%. The representative micro-Raman spectra demonstrated D and G bands for nano-GO particles containing adhesives. HA-GO-2% group demonstrated uniform diffusion in adhesive, higher μTBS, adequate durability, and comparable resin tag development to controls.

Graphene oxide nano-filler based experimental dentine adhesive. A SEM / EDX, Micro-Raman and microtensile bond strength analysis

AIM

The study aimed to assess graphene oxide (GO) adhesive and its dentin interaction using scanning electron microscopy (SEM), MicroRaman spectroscopy and Microtensile bond strength (μTBS).

MATERIALS AND METHODS

Experimental GOA and control adhesives (CA) were fabricated. Presence of GO within the experimental adhesive resin was assessed using SEM and Micro-Raman spectroscopy. Ninety specimens were prepared, sixty teeth were utilized for μTBS, twenty for SEM analysis of interface for CA and GOA and ten were assessed using microRaman spectroscopy. Each specimen was sectioned and exposed dentine was conditioned (35% phosphoric acid) for 10 s. The surface was coated twice with adhesive (15 s) and photopolymerized (20 s). Composite build-up on specimen was photo-polymerized. Among the bonded specimens, thirty specimen were assessed using Micro-Raman spectrometer, SEM and energy dispersive X-ray spectroscopy (EDX), whereas remaining specimens were divided in to three sub-groups (n = 10) based on the storage of 24 h, 8 weeks and 16 weeks. μTBS testing was performed at a crosshead speed of 0.5 mm/min using a microtensile tester. The means of μ-tbs were analyzed using ANOVA and post hoc Tukey multiple comparisons test.

RESULTS

No significant difference in μTBS of CA and GOA was observed. Storage time presented a significant interaction on the μTBS (p < 0.01). The highest and lowest μTBS was evident in CA (30.47 (3.55)) at 24 h and CA (22.88 (3.61)) at 18 weeks. Micro-Raman analysis identified peaks of 1200 cm-1 to 1800 cm1, D and G bands of GO nanoparticles in the resin. Uniform distribution of graphene oxide nanoparticles was present at the adhesive and hybrid layer.

CONCLUSION

GO showed interaction within adhesive and tooth dentin similar to CA, along with formation of hybrid layer. In ideal conditions (absence of nanoleakage), graphene oxide modified adhesive shows comparable bond strength and durability of resin dentine bond.

MoO3 Nanobelts Embedded Polypyrrole/SIS Copolymer Blends for Improved Electro-Mechanical Dual Applications

This research endeavor aimed to develop thin film blends of polypyrrole (PPy) and poly (styrene-isoprene-styrene) (SIS) with MoO₃ as a nanofiller for improved mechanical and electrical properties to widen its scope in the field of mechatronics. This study reports blends of polypyrrole (PPy) and poly (styrene-isoprene-styrene) (SIS) tri-block copolymer showing improved mechanical and electrical attributes while employing MoO₃ nanobelts as nanofillers that additionally improves the abovementioned properties in the ensuing nanocomposites. The synthesis of PPy/SIS blends and MoO₃/PPy/SIS nanocomposites was well corroborated with XRD, SEM, FTIR, and EDS analysis. Successful blending of PPy was yielded up to 15 w/w% PPy in SIS, as beyond this self-agglomeration of PPy was observed. The results showed a remarkable increase in the conductivity of insulating SIS copolymer from 1.5 × 10^−6.1 to 0.343 Scm⁻¹ and tensile strength up to 8.5 MPa with the 15 w/w% PPy/SIS blend. A further enhancement of the properties was recorded by embedding MoO₃ nanobelts with varying concentrations of the nanofillers into 15 w/w% PPy/SIS blends. The mechanical strength of the polymeric nanocomposites was enhanced up to 11.4 MPa with an increase in conductivity up to 1.51 Scm⁻¹ for 3 w/w% MoO₃/PPy-SIS blends. The resultant product exhibited good potential for electro-mechanical dual applications.

Application of Biodegradable and Biocompatible Nanocomposites in Electronics: Current Status and Future Directions

With the continuous increase in the production of electronic devices, large amounts of electronic waste (E-waste) are routinely being discarded into the environment. This causes serious environmental and ecological problems because of the non-degradable polymers, released hazardous chemicals, and toxic heavy metals. The appearance of biodegradable polymers, which can be degraded or dissolved into the surrounding environment with no pollution, is promising for effectively relieving the environmental burden. Additionally, biodegradable polymers are usually biocompatible, which enables electronics to be used in implantable biomedical applications. However, for some specific application requirements, such as flexibility, electric conductivity, dielectric property, gas and water vapor barrier, most biodegradable polymers are inadequate. Recent research has focused on the preparation of nanocomposites by incorporating nanofillers into biopolymers, so as to endow them with functional characteristics, while simultaneously maintaining effective biodegradability and biocompatibility. As such, bionanocomposites have broad application prospects in electronic devices. In this paper, emergent biodegradable and biocompatible polymers used as insulators or (semi)conductors are first reviewed, followed by biodegradable and biocompatible nanocomposites applied in electronics as substrates, (semi)conductors and dielectrics, as well as electronic packaging, which is highlighted with specific examples. To finish, future directions of the biodegradable and biocompatible nanocomposites, as well as the challenges, that must be overcome are discussed.

Electrochemical detection of Salmonella using an invA genosensor on polypyrrole-reduced graphene oxide modified glassy carbon electrode and AuNPs-horseradish peroxidase-streptavidin as nanotag

A rapid and sensitive electrochemical biosensor was constructed to detect Salmonella using invA gene biosensor. The biosensing was based on polyrrole-reduced graphene oxide (PPy-rGO) nanocomposite modified glassy carbon electrode (GCE) and signal amplification with horseradish peroxidase-streptavidin biofunctionalized gold nanoparticles (AuNPs-HRP-SA). PPy-rGO was prepared at 60 °C by chemical reduction of PPy-functionalized graphene oxide (PPy-GO) that was synthesized by in situ polymerization at room temperature. The detection signal was amplified via enzymatic reduction of H₂O₂ in the presence of hydroquinone (HQ) using AuNPs-HRP-SA as nanotag. Under optimal conditions, the differential pulse voltametric (DPV) signal from the biosensor was linearly related to the logarithm of target invA gene concentrations from 1.0 × 10^-16 to 1.0 × 10^-10 M, and the limit of detection (LOD) was 4.7 × 10^-17 M. The biosensor can also detect Salmonella in the range of 9.6 to 9.6 × 10⁴ CFU mL^-1, with LOD of 8.07 CFU mL^-1. The biosensor showed good regeneration ability, acceptable selectivity, repeatability and stability, which bode well as an alternative method for Salmonella screening.

Studies on the Electrical Properties of Graphene Oxide-Reinforced Poly (4-Styrene Sulfonic Acid) and Polyvinyl Alcohol Blend Composites

In the present study, graphene oxide (GO)-reinforced poly (4-styrenesulfonic acid) (PSSA)/polyvinyl alcohol (PVA) blend composite films were prepared using colloidal blending technique at various concentrations of GO (0–3[Formula: see text]wt.%). The morphological investigations of the prepared composites were carried out using polarized optical microscopy and scanning electron microscopy. The electrical properties of composites were evaluated using an impedance analyzer in the frequency range 50[Formula: see text]Hz to 20[Formula: see text]MHz and temperature in the range 40–150[Formula: see text]C. Morphological studies infer that GO was homogeneously dispersed in the PSSA/PVA blend matrix. Investigations of electrical property indicate that the incorporation of GO into PSSA/PVA blend matrix resulted in the enhancement of the impedance ([Formula: see text] and the quality factor ([Formula: see text]-factor) values. A maximum impedance of about 4.32[Formula: see text][Formula: see text][Formula: see text]10[Formula: see text] was observed at 50[Formula: see text]Hz and 90[Formula: see text]C for PSSA/PVA/GO composites with 3[Formula: see text]wt.% GO loading. The [Formula: see text]-factor also increased from 8.37 for PSSA/PVA blend to 59.8 for PSSA/PVA/GO composites with 3[Formula: see text]wt.% GO loading. These results indicate that PSSA/PVA/GO composites can be used for high-[Formula: see text] capacitor applications.

Luminescent Poly(vinyl alcohol)/Carbon Quantum Dots Composites with Tunable Water-Induced Shape Memory Behavior in Different pH and Temperature Environments

Luminescent water-induced shape memory polymer (SMP) composites with tunable shape recovery rate are developed by blending poly(vinyl alcohol) (PVA) and carbon quantum dots (CQDs). The oxygen and active hydrogen-rich CQDs can serve as extra physical cross-linking points in PVA via strong hydrogen bonding interaction, which largely improves the shape memory performances of PVA. At room temperature, water can successfully actuate the shape recovery of deformed PVA/CQDs composite. It is demonstrated that this water-induced shape recovery is mainly attributed to the plasticizing effect of water and its competitive hydrogen bonding. Furthermore, a quantitative bending test suggests that the shape recovery time of this water-induced SMP is tunable by altering the environmental pH value and temperature, and a relatively large shape recovery time window (from 20 to 200 s) can be achieved. In addition, the introduction of CQDs endows the PVA/CQDs SMP composites with excellent luminescent property, which makes the shape change of SMP visible under UV light. It should be noted that the mild stimulus condition and tunable shape recovery performances make the luminescent visible PVA/CQDs SMP feasible for diverse biological applications in smart medical devices, stimuli-responsive drug-release, and intelligent sensors in vivo and in vitro.