Application of ANN and RSM for Rhodamine B and Safranine-O Decolorization on Zinc-Carbon Battery Waste Derived Ag/CoFe-LDH/rGO Catalyst

The present work is first aimed at recovering graphite from carbon rods of waste zinc-carbon (Zn-C) batteries for applications such as wastewater treatment, in order to contribute to the development of a sustainable environment. Then, a composite material, cobalt-iron layered double hydroxide combination with reduced graphene oxide, and with subsequent Ag nanoparticles deposition via NaBH4 reduction method (Ag/CoFe-LDH/rGO) was prepared for the catalytic activity of Rhodamine B (RhB) and Safranine-O (SO) as model contaminants from aquatic media. The catalytic activity of RhB and SO by Ag/CoFe-LDH/rGO in the presence of NaBH4 was studied to model and optimize the process parameters (NaBH4 amount, reaction time, initial dye concentration (Co), and catalyst dosage) via central composite design (CCD)-response surface methodology (RSM). Also, an artificial neural network (ANN) model was developed to estimate the catalytic activity of each dye using an RSM data set. The catalytic activities of 99.54% and 99.96% were obtained for RhB and SO dyes, respectively, under the optimal conditions: NaBH4 amount 12.32 mM, reaction time 3.19 min, Co 33.46 mg/L, and catalyst dosage 1.24 mg/mL for RhB dye; NaBH4 amount 16.76 mM, reaction time 3.06 min, Co 15.10 mg/L, and catalyst dosage 1.46 mg/mL for SO dye. The optimum conditions of process parameters by ANN with gray wolf optimizer (GWO) were in good agreement with the points determined the RSM-CCD. These results demonstrate that RSM and ANN approaches can be applied practically and efficiently to maximize the catalytic activity of RhB and SO by Ag/CoFe-LDH/rGO in the existence of NaBH4. On the other hand, from the kinetic and thermodynamic studies, the positive activation enthalpy, ΔH# and the negative activation entropy, ΔS# values for each dye demonstrated that the catalytic performance was endothermic and less random at the solid/liquid interface.

Green Synergy Conversion of Waste Graphite in Spent Lithium-Ion Batteries to GO and High-Performance EG Anode Material

The increasing demand for graphite and the higher lithium content than environment abundance make the recycling of anode in spent lithium-ion batteries (LIBs) also become an inevitable trend. This work proposes a simple pathway to convert the retired graphite to high-performance expanded graphite (EG) under mild conditions. After the oxidation and intercalation by FeCl3 for the retired graphite, H2O2 molecules are more likely to penetrate into the extended layers. And the gas phase diffusion caused by the produced O2 from the redox reaction between FeCl3 and H2O2 further promotes lattice expansion of interlayers (0.535 nm), which is beneficial to the stripping of graphene oxide (GO) with fewer layers. The EG exhibits excellent electrochemical performances in both LIBs and sodium-ion batteries (SIBs). It delivers 331.5 mAh g-1 at 3C (1C = 372 mA g-1) in LIBs, while it achieves 176.8 mAh g-1 at 3C (1C = 120 mA g-1) in SIBs. Then the capacity retains 753.6 (LIBs) and 201.6 (SIBs) mAh g-1 after a long-term cycling of 500 times at 1C, respectively. The full cells with the EG electrodes after prelithium/presodiation also show excellent cycle stability. Thus, this work offers another referable strategy for the recycling of waste graphite in spent LIBs.

A critical review on graphene and graphene-based derivatives from natural sources emphasizing on CO2 adsorption potential

Accelerated release of carbon dioxide (CO2) into the atmosphere has become a critical environmental issue, and therefore, efficient methods for capturing CO2 are in high demand. Graphene and graphene-based derivatives have demonstrated promising potential as adsorbents due to their unique properties. This review aims to provide an overview of the latest research on graphene and its derivatives fabricated from natural sources which have been utilized and may be explored for CO2 adsorption. The necessity of this review lies in the need to explore alternative, sustainable sources of graphene that can contribute to the development of viable environmentally benign CO2 capture technologies. The review will aim to highlight graphene as an excellent CO2 adsorbent and the possible avenues, advantages, and limitations of the processes involved in fabricating graphene and its derivatives sourced from both industrial resources and organic waste-based naturally occurring carbon precursors for CO2 adsorption. This review will also highlight the CO2 adsorption mechanisms focusing on density functional theory (DFT) and molecular dynamics (MD)-based studies over the last decade.

Waste dry cell derived photo-reduced graphene oxide and polyoxometalate composite for solid-state supercapacitor applications

In the modern era, realizing highly efficient supercapacitors (SCs) derived through green routes is paramount to reducing environmental impact. This study demonstrates ways to recycle and reuse used waste dry cell anodes to synthesize nanohybrid electrodes for SCs. Instead of contributing to landfill and the emission of toxic gas to the environment, dry cells are collected and converted into a resource for improved SC cells. The high performance of the electrode was achieved by exploiting battery-type polyoxometalate (POM) clusters infused on a reduced graphene oxide (rGO) surface. Polyoxometalate (K5[α-SiMo2VW9O40]) assisted in the precise bottom-up reduction of graphene oxide (GO) under UV irradiation at room temperature to produce vanadosilicate embedded photo-reduced graphene oxide (prGO-Mo2VW9O40). Additionally, a chemical reduction route for GO (crGO) was trialed to relate to the prGO, followed by the integration of a faradaic monolayer (crGO-Mo2VW9O40). Both composite frameworks exhibit unique hierarchical heterostructures that offer synergic effects between the dual components. As a result, the hybrid material's ion transport kinetics and electrical conductivity enhance the critical electrochemical process at the electrode's interface. The simple co-participation method delivers a remarkable specific capacity (capacitance) of 405 mA h g-1 (1622 F g-1) and 117 mA h g-1 (470 F g-1) for prGO-Mo2VW9O40 and crGO-Mo2VW9O40 nanocomposites alongside high capacitance retentions of 94.5% and 82%, respectively, at a current density of 0.3 A g-1. Furthermore, the asymmetric electrochromic supercapacitor crGO//crGO-Mo2VW9O40 was designed, manifesting a broad operating potential (1.2 V). Finally, the asymmetric electrode material resulted in an enhanced specific capacity, energy, and power of 276.8 C g-1, 46.16 W h kg-1, and 1195 W kg-1, respectively, at a current density of 0.5 A g-1. The electrode materials were tested in the operating of a DC motor.

Green synthesis of flower shape ZnO-GO nanocomposite through optimized discharge parameter and its efficiency in energy storage device

Numerous solution-based methods are used to prepare zinc oxide (ZnO) and graphene oxide (GO) nanocomposite (ZnO-GO NCs) such as sol-gel, hydrothermal, and precipitation. These methods require lots of reagents and involve many stages. In this study, a novel one-step solution-based discharge method is used to prepare ZnO-GO NCs through an electrochemical discharge process (ECDP) without the use of any catalyst or toxic chemical reagent. This study focused on analyzing the effects of input parameters on the production rate of ZnO-GO NCs. The experiment was performed by using Taguchi L9 orthogonal array. Materials removal rate (MRR) is considered as output response. The results reveal that voltage is the most significant factor, followed by temperature and duty cycle for obtaining higher MRR. The optimum parameters obtained from the Minitab software for higher MRR are 40 V, 30%, and 45 °C. Further, the morphology of the nanoparticles (NCs) produced at optimum parameters is analyzed which shows flower shape NCs with multilayer graphene oxide, confirmed by the FESEM and TEM images. The XRD peak at 11.27° and Raman spectroscopy peak of G and D bands reveal GO formation. The prepared ZnO-GO NCs tested as supercapacitor activity in the KOH solution. At the optimum parameter, the specific capacitance is observed to be 523.4 F/g at 2A/g current density. The NCs electrode shows good cyclic stability, with 86% retention of specific capacitance after 5000 cycles. This study shows a promising future of converting the e-waste product into valuable nanomaterials such as GO and ZnO from used dry cell batteries.

Innovations in the synthesis of graphene nanostructures for bio and gas sensors

Sensors play a significant role in modern technologies and devices used in industries, hospitals, healthcare, nanotechnology, astronomy, and meteorology. Sensors based upon nanostructured materials have gained special attention due to their high sensitivity, precision accuracy, and feasibility. This review discusses the fabrication of graphene-based biosensors and gas sensors, which have highly efficient performance. Significant developments in the synthesis routes to fabricate graphene-based materials with improved structural and surface properties have boosted their utilization in sensing applications. The higher surface area, better conductivity, tunable structure, and atom-thick morphology of these hybrid materials have made them highly desirable for the fabrication of flexible and stable sensors. Many publications have reported various modification approaches to improve the selectivity of these materials. In the current work, a compact and informative review focusing on the most recent developments in graphene-based biosensors and gas sensors has been designed and delivered. The research community has provided a complete critical analysis of the most robust case studies from the latest fabrication routes to the most complex challenges. Some significant ideas and solutions have been proposed to overcome the limitations regarding the field of biosensors and hazardous gas sensors.

A Fast Adsorption of Azithromycin on Waste-Product-Derived Graphene Oxide Induced by H-Bonding and Electrostatic Interactions

Graphene oxide (GO) was prepared from the graphite electrode of waste dry cells, and the application of the prepared GO as a potential adsorbent for rapid and effective removal of an antibiotic, azithromycin (AZM), has been investigated. The synthesis process of GO is very simple, cost-effective, and eco-friendly. As-prepared GO is characterized by field-emission scanning electron microscopy, energy-dispersive X-ray, transmission electron microscopy, X-ray diffractometry, Fourier transform infrared spectroscopy, elemental analysis, Brunauer-Emmett-Teller sorptometry, and zeta potential analysis. The obtained GO has been employed for removal of the widely used AZM antibiotic from an aqueous solution. The quantitative analysis of AZM before and after adsorption has been carried out by liquid chromatography tandem mass spectrometry. The adsorption of AZM by GO was performed in a batch of experiments where the effects of adsorbent (GO) dose, solution pH, temperature, and contact time were investigated. Under optimum conditions (pH = 7.0, contact time = 15 min, and adsorbent dose = 0.25 g/L), 98.8% AZM was removed from the aqueous solution. The rapid and effective removal of AZM was significantly controlled by the electrostatic attractions and hydrogen bonding on the surface of GO. Adsorption isotherms of AZM onto GO were fitted well with the Freundlich isotherm model, while the kinetic data were fitted perfectly with the pseudo-second order. Therefore, the simple, cost-effective, and eco-friendly synthesis of GO from waste material could be applicable to fabricate an effective and promising low-cost adsorbent for removal of AZM from aqueous media.

Review—Recent Progress in Graphene Based Modified Electrodes for Electrochemical Detection of Dopamine

Graphene and its derivatives have been widely used for the electrochemical detection of dopamine (DA) neurotransmitter, thanks to its high surface area and excellent conductivity. Modified graphene and graphene-based nanocomposites have shown improved catalytic activity towards DA detection. Various modification approaches have been taken, including heteroatom doping and association with other nanomaterials. This review summarizes and highlights the recent advances in graphene-based electrodes for the electrochemical detection of DA. It also aims to provide an overview of the advantages of using polymer as a linker platform to form graphene-based nanocomposites applied to electrochemical DA sensors.

Chirally modified cobalt-vanadate grafted on battery waste derived layered reduced graphene oxide for enantioselective photooxidation of 2-naphthol: Asymmetric induction through non-covalent interaction

The cobalt oxide-vanadium oxide (Co₃O₄-V₂O₅) combined with reduced graphene oxide (rGO) having band gap of ∼ 3.3 eV appeared as a suitable photocatalyst for selective oxidation of 2-naphthol to BINOL. C2-symmetric BINOL was achieved with good yield using hydrogen peroxide as the oxidant under UV-light irradiation. The same catalyst was chirally modified with cinchonidine and a newly synthesized chiral Schiff base ligand having a sigma-hole center. The strong interaction of the chiral modifiers with the cobalt-vanadium oxide was truly evident from various spectroscopic studies and DFT calculations. The chirally modified mixed metal oxide transformed the oxidative CC coupling reaction with high enantioselectivity. High enantiomeric excess upto 92 % of R-BINOL was obtained in acetonitrile solvent and hydrogen peroxide as the oxidant. A significant achievement was the formation of S-BINOL in the case of the cinchonidine modified catalyst and R-BINOL with the Schiff base ligand anchored chiral catalyst. The UV-light induced catalytic reaction was found to involve hydroxyl radical as the active reactive species. The spin trapping ESR and fluorescence experiment provided relevant evidence for the formation of such species through photodecomposition of hydrogen peroxide on the catalyst surface. The chiral induction to the resultant product was found to induce through supramolecular interaction like OH…π, H…Br interaction. The presence of sigma hole center was believed to play significant role in naphtholate ion recognition during the catalytic cycle.

Synthesis and Pyrolysis of Fullerenol-stabilized Pt Nanocolloids as a unique Approach to Pt-doped Carbon

An aqueous colloidal dispersion of Pt nanoparticles (NPs) stabilized by fullerenol C₆₀ (OH)₁₂ (Pt:C₆₀ (OH)₁₂ ) was successfully synthesized via liquid-phase chemical reduction. The subsequent pyrolysis of Pt:C₆₀ (OH)₁₂ at different temperatures was conducted to afford Pt-doped carbon with different chemical compositions (Pt:C60ⁿ ). X-ray absorption spectroscopy (XAS) and Infrared (IR) absorption spectroscopy and thermogravimetric measurements revealed that the thus-prepared nanocomposite consists of Pt NPs and high valent Pt-C₆₀ (OH)₁₂ complex. One distinct feature of C₆₀ (OH)₁₂ matrix as catalyst support is the suppression of size growth of Pt NPs during the pyrolysis up to 300 °C. Electrochemical experiments using cyclic voltammetry (CV) and linear sweep voltammetry (LSV) were performed to find that Pt:C60³⁰⁰ (pyrolyzed at 300 °C) exhibited higher activity than others, that was attributed to the π-extended feature of the as-obtained carbon.

Waste-Derived Nanoparticles: Synthesis Approaches, Environmental Applications, and Sustainability Considerations

For the past few decades, a plethora of nanoparticles have been produced through various methods and utilized to advance technologies for environmental applications, including water treatment, detection of persistent pollutants, and soil/water remediation, amongst many others. The field of materials science and engineering is increasingly interested in increasing the sustainability of the processes involved in the production of nanoparticles, which motivates the exploration of alternative inputs for nanoparticle production as well as the implementation of green synthesis techniques. Herein, we start by overviewing the general aspects of nanoparticle synthesis from industrial, electric/electronic, and plastic waste. We expand on critical aspects of waste identification as a viable input for the treatment and recovery of metal- and carbon-based nanoparticles. We follow-up by discussing different governing mechanisms involved in the production of nanoparticles, and point to potential inferences throughout the synthesis processes. Next, we provide some examples of waste-derived nanoparticles utilized in a proof-of-concept demonstration of technologies for applications in water quality and safety. We conclude by discussing current challenges from the toxicological and life-cycle perspectives that must be taken into consideration before scale-up manufacturing and implementation of waste-derived nanoparticles.

Facile synthesis of battery waste-derived graphene for transparent and conductive film application by an electrochemical exfoliation method

Low defect ratio graphene with promising conductivity and transparency can be obtained from the spent graphite in Zn–C battery waste.

Graphene from discharged dry cell battery electrodes

Utilization of extracted graphite rods from discharged dry cell batteries for synthesis of graphene oxide / graphene serves two purposes, one is waste management which supports environmental safety and the second is low cost production of graphene oxide / graphene which are highly promising 2D materials in various fields of research. In the present work, a sustainable feasibility for the synthesis of graphene oxide / graphene from graphite rods of waste dry cell batteries is demonstrated. The graphite rods separated from the waste dry cell batteries were subjected to electrochemical exfoliation (ECE) in an acidic media. The graphene oxide (GO) obtained from this method was subjected to reduction heat treatment under argon atmosphere at suitable temperature and time period. Finally, the reduced graphene oxide (rGO) i.e., graphene was characterized using XRD, FTIR, Raman Spectroscopy, TGA, BET, SEM and TEM. The few layer graphene structure is supposed to be less defective in comparison to similar exfoliation techniques due to less oxygen-functional groups associated with the intermediate graphene oxide.

Green synthesis of Pt–Pd bimetallic nanoparticle decorated reduced graphene oxide and its robust catalytic activity for efficient ethylene glycol electrooxidation

A simple one-pot green synthesis technique is developed to prepare the Pt–Pd bimetallic nanoparticles decorated reduced graphene oxide nanocomposite and its robust catalytic activity for efficient and durable ethylene glycol oxidation is realized.

Potentiodynamic formation of diaminobenzene films on an electrochemically reduced graphene oxide surface: Determination of nitrite in water samples

An electrode comprised of a polydiaminobenzene (p-DAB) film formed on electrochemically reduced graphene oxide (ERGO) on a glassy carbon (GC) (p-DAB@ERGO/GC) was fabricated using a potentiodynamic method for the sensitive and selective determination of nitrite in the presence of a common interference. The p-DAB@ERGO/GC film-modified electrode surfaces were characterized by scanning electron microscopy, X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, electrochemical impedance spectroscopy and cyclic voltammetry. The film fabrication was initiated via the NH₂ groups of DAB, which was confirmed by XPS from the peaks corresponding to NH (396.7eV), NH (399.4eV), NN (400.2eV), and N⁺H (402.2eV). The Raman spectra revealed the characteristic D and G bands at 1348 and 1595cm^-1, respectively, which confirmed the fabrication of GO on the GC electrode, and the ratio of the D and G bands was increased after the electrochemical reduction of GO. The surface coverage of the modified electrode was 8.16×10^-11molcm^-2. The p-DAB@ERGO/GC film-modified electrode was used successfully for the determination of nitrite ions. The p-DAB@ERGO/GC film-modified electrode exhibited superior activity for the determination of nitrite compared to the bare GC and p-DAB@GC electrodes. The amperometric current increased linearly with increasing nitrite concentration from 7.0×10^-6 to 2.0×10^-2M. The detection limit was 30nM (S/N=3). In addition, the modified electrode was used successfully to determine the nitrite ion concentration in the presence of a 100-fold excess of common interferents. The practical application of the modified electrode was demonstrated by determining the nitrite ion concentration in water samples.