Interface Optimization of Metal Quantum Dots/Polymer Nanocomposites and their Properties: Studies of Multi-Functional Organic/Inorganic Hybrid

Nanomaterials filled polymers system is a simple method to produce organic/inorganic hybrid with synergistic or complementary effects. The properties of nanocomposites strongly depend on the dispersion effects of nanomaterials in the polymer and their interfaces. The optimized interface of nanocomposites would decrease the barrier height between filler and polymer for charge transfer. To avoid aggregation of metal nanoparticles and improve interfacial charge transfer, Pt nanodots filled in the non-conjugated polymer was synthesized with an in situ method. The results exhibited that the absorbance of nanocomposite covered from the visible light region to NIR (near infrared). The photo-current responses to typical visible light and 808 nm NIR were studied based on Au gap electrodes on a flexible substrate. The results showed that the size of Pt nanoparticles was about 1-2 nm and had uniformly dispersed in the polymer matrix. The resulting nanocomposite exhibited photo-current switching behavior to weak visible light and NIR. Simultaneously, the nanocomposite also showed electrical switching responses to strain applied to a certain extent. Well-dispersion of Pt nanodots in the polymer is attributable to the in situ synthesis of metal nanodots, and photo-current switching behavior is due to interface optimization to decrease barrier height between metal filler and polymer. It provided a simple way to obtain organic/inorganic hybrid with external stimuli responses and multi-functionalities.

Surface-constructing of visible-light Bi2WO6/CeO2 nanophotocatalyst grafted PVDF membrane for degradation of tetracycline and humic acid

The synthesis of Bi₂WO₆ and CeO₂ photocatalytic nanomaterials exhibit a great ability to photodegrade the antibiotics and shown excellent oxidation of various organic pollutants. Heterostructure 1:1 & 2:1 Bi₂WO₆/CeO₂ nanocomposite was successfully synthesized via the facile sono-dispersion method and exquisite photocatalytic activity. The 0.5 wt% of nanocomposites were well-grafted on PVDF membrane surface via an in-situ polymerization method using polyacrylic acid. The fourier transform infrared (FTIR) spectra demonstrated that the network formation in PVDF induced by the -COOH functional group in acrylic acid. The grafted membrane morphology and strong binding ability over the membranes were validated by scanning electron microscope with energy dispersion (SEM-EDS) and X-ray photoelectron spectroscopy (XPS), respectively. The permeate flux of 49.2 L.m^-2 h^-1 and 41.65 L.m^-2 h were observed for tetracycline and the humic acid solution respectively for 1 wt% of PVP and 0.5 wt% of photocatalytic nanomaterials in PVDF membrane. The tetracycline and humic acid photodegradation rate of 82% and 78% and total resistance of 1.43 × 10¹⁰ m^-1 and 1.64 × 10¹⁰ m^-1, 83.5% and 77% flux recovery ratio were observed with N5 membrane. The 2:1 Bi₂WO₆/CeO₂ nanocomposite grafted membrane showed a high permeate flux and better photodegradation ability of organic pollutants in the wastewater.

Statistical Analysis of Synthesis Parameters to Fabricate PVDF/PVP/TiO2 Membranes via Phase-Inversion with Enhanced Filtration Performance and Photocatalytic Properties

Non-solvent induced phase-inversion is one of the most used methods to fabricate membranes. However, there are only a few studies supported by statistical analysis on how the different fabrication conditions affect the formation and performance of membranes. In this paper, a central composite design was employed to analyze how different fabrication conditions affect the pure water flux, pore size, and photocatalytic activity of polyvinylidene fluoride (PVDF) membranes. Polyvinylpyrrolidone (PVP) was used to form pores, and titanium dioxide (TiO₂) to ensure the photocatalytic activity of the membranes. The studied bath temperatures (15 to 25 °C) and evaporation times (0 to 60 s) did not significantly affect the pore size and pure water flux of the membranes. The concentration of PVDF (12.5 to 17.5%) affected the viscosity, formation capability, and pore sizes. PVDF at high concentrations resulted in membranes with small pore sizes. PVP affected the pore size and should be used to a limited extent to avoid possible hole formation. TiO₂ contents were responsible for the decolorization of a methyl orange solution (10^-5 M) up to 90% over the period studied (30 h). A higher content of TiO₂ did not increase the decolorization rate. Acidic conditions increased the photocatalytic activity of the TiO₂-membranes.

Mussel-Inspired Fabrication of PDA@PAN Electrospun Nanofibrous Membrane for Oil-in-Water Emulsion Separation

Emulsified oily wastewater threatens human health seriously, and traditional technologies are unable to separate emulsion containing small sized oil droplets. Currently, oil-water emulsions are usually separated by special wettability membranes, and researchers are devoted to developing membranes with excellent antifouling performance and high permeability. Herein, a novel, simple and low-cost method has been proposed for the separation of emulsion containing surfactants. Polyacrylonitrile (PAN) nanofibers were prepared via electrospinning and then coated by polydopamine (PDA) by using self-polymerization reactions in aqueous solutions. The morphology, structure and oil-in-water emulsion separation properties of the as-prepared PDA@PAN nanofibrous membrane were tested. The results show that PDA@PAN nanofibrous membrane has superhydrophilicity and almost no adhesion to crude oil in water, which exhibits excellent oil-water separation ability. The permeability and separation efficiency of n-hexane/water emulsion are up to 1570 Lm-2 h-1 bar-1 and 96.1%, respectively. Furthermore, after 10 cycles of separation, the permeability and separation efficiency values do not decrease significantly, indicating its good recycling performance. This research develops a new method for preparing oil-water separation membrane, which can be used for efficient oil-in-water emulsion separation.

Designing of a novel polyvinylidene fluoride/TiO2/UiO-66-NH2 membrane with photocatalytic antifouling properties using modified zirconium-based metal-organic framework

Novel polyvinylidene fluoride/TiO₂/UiO-66-NH₂ (PVDF/TiUN) membranes were produced by the delay phase separation method via introducing the TiO₂/UiO-66-NH₂ (TiUN) nanocomposite into PVDF casting solution. Interconnection of TiO₂ and UiO-66-NH₂ improved photocatalysis capacity and endowed PVDF/TiUN membranes with self-cleaning capability. Quantitative measurements showed that, firstly, PVDF/TiUN membranes exhibited improved photodegradation kinetics and efficiency (up to 88.1%) to Rhodamine B (RhB). Secondly, the performances of bovine serum albumin (BSA) rejection and permeation of PVDF/TiUN membranes outperformed those of other check samples, indicating enhanced hydrophilicity. Thirdly, rejection rate of BSA reached a breathtaking 98.14% and flux recovery ratio (FRR) of BSA reached a breathtaking 95.37%. Thus, given their excellent anti-contamination property and separation performance, the PVDF/TiUN membrane is very likely to be a novel water treatment membrane.

A Novel PAN-GO-SiO₂ Hybrid Membrane for Separating Oil and Water from Emulsified Mixture

In this article, we report the development of a polyacrylonitrile-graphene oxide-silicon dioxide (PAN-GO-SiO₂) hybrid membrane for separation of oil and water from their emulsified mixture. The membrane was successfully fabricated using a one-step electrospinning process. GO and SiO₂ nanofillers were added in PAN in different concentrations to determine the optimized composition for the PAN-GO-SiO₂ hybrid membrane. A scanning electron microscopy (SEM) examination showed that the nanofillers were uniformly embedded in the nanofibrous structure of the electrospun hybrid membrane. The GO was mainly embedded inside the PAN nanofibers, causing knots while SiO₂ nanoparticles were found embedded on the nanofiber surface, resulting in the formation of micro-nano protrusions on the fiber surface. The formation of these hierarchical structures, together with enhanced hydrophilicity due to oxygen containing groups on both SiO₂ and GO, resulted in a high rejection (>99%) of oil from oil-water emulsion. Membrane performance evaluation under gravity separation tests showed that the separation flux and phase rejection was enhanced with the incorporation of nanofillers. The inclusion of nanofillers also enhanced the mechanical properties of the membrane. The best flux and phase separation performance was obtained for an optimized concentration of 7.5 wt % SiO₂ and 1.5 wt % GO in PAN. The flux of separated water was enhanced from 2600 L m^-2 h^-1 for pristine PAN to 3151 L m^-2 h^-1 for PAN-GO-SiO₂. The hybrid membrane also showed good mechanical and chemical stability, and antifouling propensity.

B. Bionic creation of nano-engineered Janus fabric for selective oil/organic solvent absorption

We present a self-driven and tunable hydrophobic/oleophilic, wettability-modified Janus fabric composed of a cellulosic substrate engineered with nanofibers via facile a electrospinning technique that exhibits one-step selective oil absorption capacity from water.

Dramatic visible light photocatalytic degradation due to the synergetic effects of TiO2 and PDA nanospheres

Dramatic visible light photocatalytic activity was obtained for the degradation of methyl orange using TiO₂ photocatalysts modified with polydopamine (PDA) nanospheres.