Studying Fluorescence Sensing of Acetone and Tryptophan and Antibacterial Properties Based on Zinc-Based Triple Interpenetrating Metal-Organic Skeletons

Two triple interpenetrating Zn(II)-based MOFs were studied in this paper. Named [Zn6(1,4-bpeb)4(IPA)6(H2O)]n (MOF-1) and {[Zn3(1,4-bpeb)1.5(DDBA)3]n·2DMF} (MOF-2), {1,4-bpeb = 1,4-bis [2-(4-pyridy1) ethenyl]benze, IPA = Isophthalic acid, DDBA = 3,3'-Azodibenzoic acid}, they were synthesized by the hydrothermal method and were characterized and stability tested. The results showed that MOF-1 had good acid-base stability and solvent stability. Furthermore, MOF-1 had excellent green fluorescence and with different phenomena in different solvents, which was almost completely quenched in acetone. Based on this phenomenon, an acetone sensing test was carried out, where the detection limit of acetone was calculated to be 0.00365% (volume ratio). Excitingly, the MOF-1 could also be used as a proportional fluorescent probe to specifically detect tryptophan, with a calculated detection limit of 34.84 μM. Furthermore, the mechanism was explained through energy transfer and competitive absorption (fluorescence resonance energy transfer (FRET)) and internal filtration effect (IFE). For antibacterial purposes, the minimum inhibitory concentrations of MOF-1 against Escherichia coli and Staphylococcus aureus were 19.52 µg/mL and 39.06 µg/mL, respectively, and the minimum inhibitory concentrations of MOF-2 against Escherichia coli and Staphylococcus aureus were 68.36 µg/mL and 136.72 µg/mL, respectively.

Sensitive and Rapid Detection of Aspartic Acid with Co3O4-ZnO Nanorods Using Differential Pulse Voltammetry

Herein, the detection of aspartic acid by doped Co₃O₄-ZnO nanorod materials was proposed using differential pulse voltammetry. The nano-composite metal oxide was synthesized by the wet precipitation method in basic media. Aspartic acid is a non-essential amino acid naturally synthesized in the body with lot of health significance, including as a biomarker for several health deficiencies. The synthesized composite Co₃O₄-ZnO nanorod was well-investigated by using FESEM, XRD, XPS, FTIR, UV/vis., EIS, and CV. The synthesized composite exhibited a low limit of detection (0.03 µM, high sensitivity (0.0014 µA µM^-1 cm^-2) and wide linear range (0.05-50 µM) for aspartic acid. The substrate, the Co₃O₄-ZnO nanorod, enhanced the electro-catalytic oxidation of aspartic acid as a result of its catalytic and conductivity properties. The developed sensor based on Co₃O₄-ZnO has a repeatable, reproducible and stable current response for aspartic acid. Additionally, other electroactive compounds did not interfere with the sensor's current response. The suitability of the developed sensor for real sample analysis was also established. Therefore, this study proposed the potential use of Co₃O₄-ZnO nanorod material in healthcare management for the maintenance of human well-being.

A reversible coumarin-based sensor for intracellular monitoring cysteine level changes during Cu2+-induced redox imbalance

Biological thiols are crucial small molecule amino acids widely existing in cells, which play indispensable roles in maintaining redox homeostasis of living systems. Owing to their abnormal levels have close relation with many diseases, thus, developing more convenient, rapid and practical in-vivo detection tools is imminent. Herein, a reversible coumarin-based probe (HNA) was successfully constructed through a simple two-step synthesis. HNA can detect Cys/Hcy with high response speed and desirable selectivity based on Michael addition recognition mechanism. Free HNA has an orange emission at 580 nm, but after addition of Cys/Hcy, the conjugated structure of probe HNA was destroyed by the attack of sulfhydryl, resulting in a new green emission at 507 nm. Further, HNA has been applied to monitor Cys/Hcy in HeLa cells and zebrafish. Notably, HNA has also been successfully applied for real-time tracing Cys levels changes in living cells and zebrafish during the imbalance in redox status caused by copper (II). This provides a new strategy for studying the process of oxidative stress in cells.

A coumarin-based fluorescence sensor for rapid discrimination of cysteine/homocysteine and glutathione under dual excitation wavelengths

Biological thiols (Cys, Hcy and GSH) are crucial biomolecules in living cells and play indispensable roles in maintaining the redox homeostasis of organisms. But due to their similar molecular structure, the development of effective tools for distinguishing two or three of them remains a great difficulty. Herein, we constructed a sensitive sensor (CB) by connecting the bifunctional fluorescent reagent with coumarin derivatives for simultaneous recognition of these three thiols through different pathways. Free CB had no fluorescence; however, with gradual addition of thiols, the chlorine unit was replaced by sulfhydryl. Furthermore, the intramolecular rearrangement occurred between the amino and sulfhydryl groups of Cys/Hcy and yellow fluorescence was observed at 570 nm. However, GSH with a large structure could not undergo intramolecular rearrangement, and green fluorescence was excited at 505 nm. In this way, Cys/Hcy and GSH can be detected distinctively. Under dual excitation wavelengths, CB exhibited high selectivity and fast response to the three thiols. Furthermore, CB was successfully applied to imaging endogenous and exogenous thiols in living cells and zebrafish, providing us with a reliable tool for thiols recognition.

Various Cd(ii) coordination polymers induced by carboxylates: multi-functional detection of Fe3+, anions, aspartic acids and bovine serum albumin

By adjusting carboxylates, six Cd(ii) coordination polymers based on a naphthalene-methylene mixed-bridged-amide ligand, [Cd(L)(DNBA)2] (1), [Cd2(L)2(BDC)2(H2O)2]·2H2O (2), [Cd(L)(1,4-CHDA)] (3), [Cd(L)(HIPA)(H2O)]·H2O (4), [Cd(L)(MIP)]·H2O (5), and [Cd(L)(PMA)0.5(H2O)]·H2O (6) [L = N,N'-bis(4-methylenepyridin-4-yl)-1,4-naphthalene dicarboxamide, HDNBA = 3,5-dinitrobenzoic acid, H2BDC = 1,4-benzenedicarboxylic acid, 1,4-H2CHDA = 1,4-cyclohexanedicarboxylic acid, H2HIPA = 5-hydroxyisophthalic acid, H2MIP = 5-methylisophthalic acid and H4PMA = pyromellitic acid] have been synthesized under hydrothermal conditions. 1 shows a 4-c sql coplanar structure. 2 exhibits a 2-fold vertical interpenetrating structure based on wave-like 4-c sql layers. 3 shows a (3,5)-c pnh network containing a unique μ3-L. 4 features a 4-c sql wave-like network. 5 and 6 exhibit 3D structures with 6-c pcu and 4-c mog topologies. The number of carboxyl groups and functional group positions of the carboxylates have an important influence on the structures of the title complexes. The fluorescent responses of 1-6 towards Fe3+, anions, aspartic acid and bovine serum albumin were investigated. Among them, 4 shows sensitivity and selectivity (KSV = 1.16 × 104 L mol-1 for Fe3+, 1.03 × 104 L mol-1 for CrO42-, 1.08 × 104 L mol-1 for Cr2O72-, 1.17 × 104 L mol-1 for MnO4- and 1.05 × 104 L mol-1 for aspartic acid).

Micromesoporous Nitrogen-Doped Carbon Materials Derived from Direct Carbonization of Metal-Organic Complexes for Efficient CO2 Adsorption and Separation

Metal-organic complexes (MOCs) are considered as excellent precursors to prepare carbon materials, due to the fact that heteroatoms and functional groups can be naturally reserved in the resulting carbon materials through the carbonization. Herein, micromesoporous nitrogen-doped carbons MPNC-1 and MPNC-2 are successfully obtained by direct carbonization (800 °C, KOH activation) of metal-organic complexes DQA-1 and DQA-2. MPNC-1 and MPNC-2 exhibit high BET surface area (2368.9 and 2327.6 m² g^-1), pore volume (1.95 and 1.89 cm³ g^-1), and N contents (17.2% and 12.3%). At 25 °C and 1 bar, MPNC-1 and MPNC-2 show high CO₂ adsorption of 7.53 and 6.58 mmol g^-1, the estimated CO₂/N₂ selectivity are 20.5 and 22.6, indicating excellent promise for practical CO₂ adsorption and separation applications. Theoretical calculation indicates carbon surfaces with pyridinic-N, pyrrolic-N, and graphitic-N coexistence could strongly change the local electronic distribution and electrostatic surface potential, enhancing the CO₂ adsorption with adsorption energy of -58.96 kJ mol g^-1. Theoretical calculation also highlights that CO₂ adsorption mechanism is electrostatic interaction with a large green isosurface between CO₂ molecules and the carbon surface.

A quinoline-based probe for effective and selective sensing of aspartic acid in aqueous medium: in vitro and in vivo live cell imaging

A highly sensitive and selective “on–off–on” chemosensor for aspartic acid in aqueous solution was established. In vitro live cell imaging against MCF 7 cells and in vivo imaging using C. elegans were successfully demonstrated.

Conventional and Mechanochemical Syntheses of Copper(I) Iodide Luminescent MOF with Bis(amidoquinoline) and Its Application for the Detection of Amino Acid in Aqueous Solution

Formation of a copper(I) iodide cluster based luminescent metal-organic frameworks (LMOFs) and its utilization for the detection of cysteine (Cys) in aqueous solution are reported. The reaction of bis(amidoquinoline) ligand (L) with copper(I) iodide afforded an LMOF {[(Cu₂I₂)L₂]·2DMSO} _n (1) with a 4⁴-sql topology linked by Cu₂I₂ clusters as a thermodynamic product. Time- and temperature-dependent PXRD experiments confirmed that the entire formation process for 1 is kinetically and thermodynamically controlled. Interestingly, LMOF 1 was also obtained under the mechanochemical condition. Moreover, LMOF 1 dispersed in water shows a selective quenching for Cys over other amino acids due to the strong affinity of Cys to copper(I) iodide. On the basis of the NMR data of L isolated from the decomposition of 1, the decomposition-displacement mechanism was proposed for the sensing of Cys. This result might be utilized for the practical detection of Cys because the sensing material can be prepared simply, and the sensing process is performed in aqueous media.

Nitrogen-Doped Microporous Carbons Derived from Pyridine Ligand-Based Metal-Organic Complexes as High-Performance SO2 Adsorption Sorbents

Heteroatom-doped porous carbons are emerging as platforms for gas adsorption. Herein, N-doped microporous carbon (NPC) materials have been synthesized by carbonization of two pyridine ligand-based metal-organic complexes (MOCs) at high temperatures (800, 900, 1000, and 1100 °C). For NPCs (termed NPC-1- T and NPC-2- T, where T represents the carbonization temperature), the micropore is dominant, pyridinic-N and other N atoms of MOC precursors are mostly retained, and the N content reaches as high as 16.61%. They all show high Brunauer-Emmett-Teller surface area and pore volume, in particular, NPC-1-900 exhibits the highest surface areas and pore volumes, up to 1656.2 m² g^-1 and 1.29 cm³ g^-1, respectively, a high content of pyridinic-N (7.3%), and a considerable amount of SO₂ capture (118.1 mg g^-1). Theoretical calculation (int = ultrafine m062x) indicates that pyridinic-N acts as the leading active sites contributing to high SO₂ adsorption and that the higher content of pyridinic-N doping into the graphite carbon layer structure could change the electrostatic surface potential, as well as the local electronic density, which enhanced SO₂ absorption on carbon edge positions. The results show great potential for the preparation of microporous carbon materials from pyridine ligand-based MOCs for effective SO₂ adsorption.

Hot-Pressing Method To Prepare Imidazole-Based Zn(II) Metal-Organic Complexes Coatings for Highly Efficient Air Filtration

Particulate matters (PMs) air pollution has become a serious environmental issue due to its great threat to human health. Herein, metal-organic complexes PBM-Zn1 and PBM-Zn2 coatings (noted as PBM-Zn-Filter) have been produced by the hot-pressing method on various substrates for the first time. Layer-by-layer PBM-Zn-Filters were also obtained through varying hot-pressing cycles. The obtained PBM-Zn-Filters with high robustness show excellent performance in PMs removal. In particular, benefiting from thelarger conjugation system, micropore structure, lower pressure drop, higher electrostatic potential ζ, and electron cloud exposed metal center of PBM-Zn2 (DFT calculations), PBM-Zn2@melamine foam-4 gives the highest removal rates, PM2.5:99.5% ± 1.2% and PM10:99.3% ± 1.1%, and the removal efficiency for capture PM2.5 and PM10 particles in cigarette smoke were both retained at high levels (>95.5%) after 24 h tests. More importantly, a homemade mask is made up by imbedding the PBM-Zn2@melamine foam-4 into a commercial breathing mask, which shows higher removal efficiency, lower pressure drop, smaller thickness, and higher quality factor than two commercial breathing masks, the PMs removal efficiencies for both PM2.5 and PM10 are 99.6% ± 0.5% and 99.4% ± 0.8%, and acceptable air resistance are demonstrated.

Synthesis and application of a highly selective copper ions fluorescent probe based on the coumarin group

A highly selective copper ions fluorescent probe based on the coumarin-type Schiff base derivative 1 (probe) was produced by condensation reaction between coumarin carbohydrazide and 1H-indazole-3-carbaldehyde. The UV-vis spectroscopy showed that the maximum absorption peak of compound 1 appeared at 439nm. In the presence of Cu²⁺ ions, the maximum peak decreased remarkably compared with other physiological important metal ions and a new absorption peak at 500nm appeared. The job's plot experiments showed that complexes of 1:2 binding mode were formed in CH₃CN:HEPES (3:2, v/v) solution. Compound 1 exhibited a strong blue fluorescence. Upon addition of copper ions, the fluorescence gradually decreased and reached a plateau with the fluorescence quenching rate up to 98.73%. The detection limit for Cu²⁺ ions was estimated to 0.384ppm. Fluorescent microscopy experiments demonstrated that probe 1 had potential to be used to investigate biological processes involving Cu²⁺ ions within living cells.

Two luminescent lanthanide–organic frameworks containing bithiophene groups for the selective detection of nitrobenzene and Fe3+

Two isostructural lanthanide–organic frameworks containing bithiophene groups can be used as fast-response fluorescent probes for the sensitive detection of nitrobenzene and Fe³⁺ ions through fluorescence quenching.

Construction of two Zn(ii)/Cd(ii) multifunctional coordination polymers with mixed ligands for catalytic and sensing properties

Two Zn(ii)/Cd(ii) coordination polymers with different networks were constructed with mixed ligands. The former compound shows high catalytic activity for Knoevenagel condensation, and the latter compound can selectively recognize l-cysteine through the luminescence quenching effect.