Synthesis and Characterization of High-Purity Mesoporous Alumina with Excellent Adsorption Capacity for Congo Red

We explore a more concise process for the preparation of high-purity alumina and to address the problem of some conventional micro- and nano-adsorbents having difficulty in exposing their adsorption sites to target pollutants in solution due to the heavy aggregation of the adsorbent, which confers poor adsorption properties. The methods of using gamma-phase high-purity mesoporous alumina (HPMA), with its excellent adsorption properties and high adsorption rates of Congo Red, and of using lower-cost industrial aluminum hydroxide by direct aging and ammonium salt substitution were successfully employed. The results showed that the purity of HPMA was as high as 99.9661% and the total removal rate of impurities was 98.87%, a consequence of achieving a large specific surface area of 312.43 m² g^-1, a pore volume of 0.55 cm³ g^-1, and an average pore diameter of 3.8 nm. The adsorption process was carried out at 25 °C, the concentration of Congo Red (CR) dye was fixed at 250 mg L^-1 and the amount of adsorbent used was 100 mg. The HPMA sample exhibited an extremely fast adsorption rate in the first 10 min, with adsorption amounts up to 476.34 mg g^-1 and adsorption efficiencies of 96.27%. The adsorption equilibrium was reached in about 60 min, at which time the adsorbed amount was 492.19 mg g^-1 and the dye removal rate was as high as 98.44%. One-hundred milligrams of adsorbent were weighed and dispersed in 200-mL CR solutions with mass concentrations ranging from 50-1750 mg L^-1 to study the adsorption isotherms. This revealed that the saturation adsorption capacity of the produced HPMA was 1984.64 mg g^-1. Furthermore, the process of adsorbing Congo Red in the synthesized product was consistent with a pseudo-second order model and the Langmiur model. It is expected that this method of producing HPMA will provide a productive, easy and efficient means of treating toxic dyes in industrial wastewater.

Study on the Synthesis of High-Purity γ-Phase Mesoporous Alumina with Excellent CO2 Adsorption Performance via a Simple Method Using Industrial Aluminum Oxide as Raw Material

To mitigate the global greenhouse effect and the waste of carbon dioxide, a chemical raw material, high-purity γ-phase mesoporous alumina (MA) with excellent CO₂ adsorption performance was synthesized by the direct aging method and ammonium salt substitution method. With this process, not only can energy consumption and time be shortened to a large extent but the final waste can also be recycled to the mother liquor by adding calcium hydroxide. Reaction conditions, i.e., pH value, calcination temperature, and desodium agent, were investigated in detail with the aid of X-ray fluorescence spectrum (XRF), X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET) and Barret-Joyner-Hallender (BJH) methods, nonlocal density functional theory (NLDFT), transmission electron microscopy (TEM), temperature-programmed desorption of CO₂ (CO₂-TPD), and presented CO₂ adsorption measurement. The results of this study are summarized as follows: the impurity content of the MA synthesized under optimal conditions is less than 0.01%, and its total removal rate of impurities is 99.299%. It was found that the MA adsorbent has a large specific surface area of 377.8 m²/g, pore volume of 0.55 cm³/g, and its average pore diameter is 3.1 nm. Under the condition of a gas flow rate of 20 cm³/min, its CO₂ adsorption capacity is 1.58 mmol/g, and after 8 times of cyclic adsorption, the amount of CO₂ adsorption remained basically unchanged, both of which indicate that the material has excellent adsorption properties and can be widely used for the adsorption of carbon dioxide.

A low temperature organic synthesis of monodispersed NiRu nanocrystals for CO2 methanation

In this study, monodispersed NiRu nanocrystals with a diameter of 3 nm were synthesized at 90 °C via a tuning hot-inject method to lower the temperature of the organic phase synthesis of monodispersed nanomaterials. The key factor for the nanocrystalline formation of NiRu alloy nanocrystals was summarized in detail. Simultaneously, the synergistic effect of Ni and Ru in CO2 methanation was explored. Doping trace Ru can significantly improve the conversion rate of CO2 methanation and CH4 selectivity. The underlying mechanism was studied in detail via X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), temperature-programmed hydrogen reduction (H2-TPR) and desorption (H2-TPD) tests, and temperature-programmed desorption of CO2 (CO2-TPD). This study gives out a new way for the general synthesis of monodisperse nickel-based nanocrystals and provides a reference for the development and application of monodispersed nanoparticles for CO2 methanation.

Ultradeep hydrodesulfurization of fuel over superior NiMoS phases constructed by a novel Ni(MoS4)2(C13H30N)2 precursor

Ni(MoS₄)₂(C₁₃H₃₀N)₂ was synthesized and adopted for preparing a NiMoS/γ-Al₂O₃ hydrodesulfurization catalyst, and the as-prepared catalyst exhibits superior 4,6-dimethyldibenzothiophene hydrodesulfurization activity.

Enhanced catalytic activity of monodispersed porous Al2O3 colloidal spheres with NiMo for simultaneous hydrodesulfurization and hydrogenation

Fabrication of monodispersed porous Al₂O₃ spheres with controlled morphologies.

One pot synthesis of NiMo–Al2O3 catalysts by solvent-free solid-state method for hydrodesulfurization

A simple and solvent-free solid-state method was used to prepare NiMo–Al₂O₃ hydrodesulfurization (HDS) catalysts using Ni(NO₃)₂·6H₂O, (NH₄)₆Mo₇O₂₄·4H₂O, and AlCl₃·6H₂O as the solid raw materials and polyethylene glycol (PEG) as an additive.