Low-Temperature Oxidation Removal of Formaldehyde Catalyzed by Mn-Containing Mixed-Oxide-Supported Bismuth Oxychloride in Air

The Mn-containing mixed-oxide-supported bismuth oxychloride (BiOCl) catalysts were prepared by calcining their corresponding parent hydrotalcite supported BiOCl. The crystal structure of BiOCl was found to be intact during calcination, while significant differences appeared in the chemical state of Mn and the redox capacities of the catalysts before and after calcination. Compared to the hydrotalcite-supported catalysts, the mixed-oxide-supported BiOCl showed much higher catalytic performance in the oxidation removal of formaldehyde due to the synergetic catalysis of more surface oxygen vacancies and higher surface basicity. The complete removal of formaldehyde could be achieved at 70 °C, and the removal efficiency was maintained more than 90% for 21 h. A possible reaction mechanism was also proposed.

A high-response formaldehyde sensor based on fibrous Ag-ZnO/In2O3 with multi-level heterojunctions

Timely detection of formaldehyde is pivotal because formaldehyde is slowly released from the indoor decorative materials, jeopardizing our healthy. Herein, a high-response formaldehyde gas sensor based on Ag-ZnO/In₂O₃ nanofibers was successfully fabricated. Compared with all the control samples, the hybrid exhibits superior sensitivity (0.65 ppm^-1), excellent selectivity (≥ 12.5) and durable stability (the deviation value ≤ 3%). Particularly, an ultra-high response value of about 186 towards 100 ppm of formaldehyde at 260 °C was achieved, heading the list of outstanding candidates. Additionally, the limit of detection is as low as 9 ppb. The enhanced gas sensing properties can be mainly attributed to multi-level heterojunctions (n-n heterojunction and Ohmic junction) and the "spill-over" effect of Ag, ultimately increasing the adsorption of gas molecules on the surface of sensing material. This work verifies that proper design of multi-level heterojunctions significantly upgrade the sensing performance.

Synthesis of Pt-Loaded NiFe-LDH Nanosheets on Wood Veneer for Efficient Gaseous Formaldehyde Degradation

Traditional methods of removing gaseous formaldehyde are often associated with high energy consumption and secondary pollution. In this study, a new wood veneer-based composite decorated with Pt-loaded NiFe-LDH nanosheets is successfully developed by a hydrothermal reaction and impregnation-chemical reduction. NiFe-LDH nanosheets as an adsorbent can capture formaldehyde molecules through their abundant hydroxyl groups. Pt nanoparticles as catalytic centers are evenly distributed on the surface of NiFe-LDH to excite the O atoms linked to NiFe-LDH and absorbed oxygen, which will further attack the absorbed formaldehyde molecules to generate CO₂ and H₂O. And the wood veneer not only increases the active area of the catalyst by endowing it with good dispersion but also provides convenient channels for reactants and products. In a simulated dark environment at room temperature, this synthetic wood veneer-based composite exhibits admirable catalytic activity, which can effectively degrade almost all gaseous formaldehyde with the initial concentration of 0.2 mg m^-3 in 30 min and maintain a high catalytic activity of ≥97% after 10 cycles. This paper presents a feasible strategy for synthesizing an energy-efficient and ecofriendly wood veneer-based composite for efficient gaseous formaldehyde degradation at room temperature, which may play an important role in indoor air purification as a promising decorative material.

A signal-decreased electrochemical immunosensor for the sensitive detection of LAG-3 protein based on a hollow nanobox-MOFs/AuPt alloy

In this work, hollow nanobox metal-organic framework (HNM) nanocomposites were synthesised and utilised for the first time in a signal decreased electrochemical immunosensor for the ultrasensitive quantitative determination of lymphocyte activation gene-3 (LAG-3) protein, which is a newly discovered biomarker. With the aid of signal materials, namely, SiO₂-tagged anti-LAG-3 antibody (SiO₂-Ab₂) and the biotin-streptavidin system, the sensor can achieve signal amplification. Encapsulation of tin dioxide-functionalised reduced graphene oxide (rGO-SnO₂) and gold and platinum alloys (AuPt alloys) onto the surface of hollow nanobox metal-organic frameworks (MOFs) was performed to prepare rGO-SnO₂/hollow nanobox-MOFs/AuPt alloys (rGO-SnO₂/HNMs/AuPt) as the matrix. SiO₂-Ab₂, which is used as the signal-decreased label, can be utilised to enhance the distinction of the electrochemical signal after the specific recognition between antibodies and antigens, owing to its large steric hindrance property. In this sensor, this proposed sandwich immunosensor can achieve a high sensitivity, especially in the presence of low concentrations of the LAG-3 protein. Under optimal conditions, this sandwich-designed immunosensor exhibited a sensitive detection of the LAG-3 protein from concentrations of 0.01 ng mL^-1 to 1 μg mL^-1, with a lower detection limit of 1.1 pg mL^-1 (based on 3σ). We proposed that this ultrasensitive biosensor can be utilised for the detection of the LAG-3 protein in early clinical tumour diagnosis.

A novel method to delaminate nitrate-intercalated MgAl layered double hydroxides in water and application in heavy metals removal from waste water

Nitrate-intercalated MgAl layered double hydroxide (LDH) was successfully delaminated in water by a facile and effective method upon reflux at 120 °C for 24 h followed by sonication at 40 °C for 5 h. This process is environmentally friendly since water is the only solvent used. The delaminated nanosheets were characterized by microscopic, spectroscopic, and particle size analyses. The delamination process successfully produced octahedron-shaped single-layer nanosheets 50-150 nm in size. X-ray photoelectron spectroscopy (XPS) data confirmed that the surface elements and their chemical status are consistent with the basic layer of MgAl LDH. The delaminated nanosheets displayed higher adsorption capacity for removing heavy metals from waste water than the original powdered LDH. After treating the waste water, a sharp and intense peak in the X-ray powder diffraction (XRD) pattern of the precipitate confirms the restacking of the LDH nanosheets.

Ag–K/MnO2 nanorods as highly efficient catalysts for formaldehyde oxidation at low temperature

A series of Ag–K/MnO₂ nanorods with various molar ratios of K/Ag were synthesized by a conventional wetness incipient impregnation method. The as-prepared catalysts were used for the catalytic oxidation of HCHO. The Ag–K/MnO₂ nanorods with an optimal K/Ag molar ratio of 0.9 demonstrated excellent HCHO conversion efficiency of 100% at a low temperature of 60 °C. The structures of the samples were investigated by BET, TEM, SEM, XRD, H₂-TPR, O₂-TPD and XPS. The results showed that Ag–0.9K/MnO₂-r exhibited more facile reducibility and greatly abundant surface active oxygen species, endowing it with the best catalytic activity of the studied catalysts. This work provides new insights into the development of low-cost and highly efficient catalysts for the removal of HCHO.

Ag–K/MnO₂ nanorods with appropriate K/Ag ratio demonstrated excellent catalytic activity for complete oxidation of formaldehyde.

A Facile Green Synthetic Route for the Preparation of Highly Active γ-Al2O3 from Aluminum Foil Waste

A novel green preparation route to prepare nano-mesoporous γ-Al₂O₃ from AlCl₃.6H₂O derived from aluminum foil waste and designated as ACFL550 is demonstrated, which showed higher surface area, larger pore volume, stronger acidity and higher surface area compared to γ-Al₂O₃ that is produced from the commercial AlCl₃ precursor, AC550. The produced crystalline AlCl₃.6H₂O and Al(NO₃)₃.9H₂O in the first stage of the preparation method were characterized by single-crystal XRD, giving two crystal structures, a trigonal (R-3c) and monoclinic (P2₁/c) structure, respectively. EDX analysis showed that ACFL550 had half the chlorine content (Cl%) relative to AC550, which makes ACFL550 a promising catalyst in acid-catalysed reactions. Pure and modified ACFL550 and AC550 were applied in acid-catalysed reactions, the dehydration of methanol to dimethyl ether and the total methane oxidation reactions, respectively. It was found that ACFL550 showed higher catalytic activity than AC550. This work opens doors for the preparation of highly active and well-structured nano-mesoporous alumina catalysts/supports from aluminum foil waste and demonstrates its application in acid-catalysed reactions.

Catalytic decomposition and mechanism of formaldehyde over Pt–Al2O3 molecular sieves at room temperature

Al₂O₃ molecular sieve supported Pt was prepared for catalytic formaldehyde oxidation at room temperature.