Laser-Induced Vertical Graphene Nanosheets for Electrocatalytic Hydrogen Evolution

Efficient and affordable electrocatalysts are fundamental for the sustainable production of hydrogen from water electrolysis. Here, an approach for the rapid production of laser-induced vertical graphene nanosheets (LIVGNs) through the exfoliation of the graphite foil under laser irradiation is presented. The density of the formed LIVGNs is ∼3 per 100 μm2. On leveraging the inherent flexibility and conductivity of the graphite foil substrate, the resulting LIVGNs exhibit a 2.2-fold increase in capacitance, making them promising candidates for electrode applications. The laser-induced surface reconstruction introduces abundant sharp edges to the LIVGNs, enhancing their electrocatalytic potential for hydrogen evolution. In electrocatalytic hydrogen evolution tests in acidic media, the LIVGNs demonstrate superior performance with a remarkable decrease in the required overpotential at 10 mA cm-2, from -555 mV for the pristine graphite foil to -348 mV for LIVGNs. This improvement is attributed to the active sites provided by the sharp edges, facilitating hydrogen species adsorption. Furthermore, the hydrophilic behavior of LIVGNs is enhanced through the anchoring of oxygen-containing groups, promoting the rapid release of the produced hydrogen bubbles. Importantly, the modified LIVGN electrode exhibits long-term stability across a wide range of current densities during chronoamperometry tests. This research introduces a transformative strategy for the efficient preparation of vertical graphene sheets on conductive graphite foils, showcasing their potential applications in electrocatalysis and energy storage.

Insights into the Stability of Graphene Oxide Aqueous Dispersions

Understanding graphene oxide's stability (or lack thereof) in liquid solvents is critical for fine-tuning the material's characteristics and its potential involvement in future applications. In this work, through the use of structural and surface investigations, the alteration of the structural and edge-surface properties of 2D graphene oxide nanosheets was monitored over a period of eight weeks by involving DLS, zeta potential, XRD, XPS, Raman and FT-IR spectroscopy techniques. The samples were synthesized as an aqueous suspension by an original modified Marcano-Tour method centred on the sono-chemical exfoliation of graphite. Based on the acquired experimental results and the available literature, a phenomenological explanation of the two underlying mechanisms responsible for the meta-stability of graphene oxide aqueous dispersions is proposed. It is based on the cleavage of the carbon bonds in the first 3-4 weeks, while the bonding of oxygen functional groups on the carbon lattice occurs, and the transformation of epoxide and hydroxyl groups into adsorbed water molecules in a process driven by the availability of hydrogen in graphene oxide nanosheets.

Boost of Charge Storage Performance of Graphene Nanowall Electrodes by Laser-Induced Crystallization of Metal Oxide Nanostructures

Major research efforts are being carried out for the technological advancement to an energetically sustainable society. However, for the full commercial integration of electrochemical energy storage devices, not only materials with higher performance should be designed and manufactured but also more competitive production techniques need to be developed. The laser processing technology is well extended at the industrial sector for the versatile and high throughput modification of a wide range of materials. In this work, a method based on laser processing is presented for the fabrication of hybrid electrodes composed of graphene nanowalls (GNWs) coated with different transition-metal oxide nanostructures for electrochemical capacitor (EC) applications. GNW/stainless steel electrodes grown by plasma enhanced chemical vapor deposition were decorated with metal oxide nanostructures by means of their laser surface processing while immersed in aqueous organometallic solutions. The pseudocapacitive nature of the laser-induced crystallized oxide materials prompted an increase of the GNW electrodes' capacitance by 3 orders of magnitude, up to ca. 28 F/cm³ at 10 mV/s, at both the positive and negative voltages. Finally, asymmetric aqueous and solid-state ECs revealed excellent stability upon tens of thousands of charge-discharge cycles.

Poly(Vinyl Chloride) Spheres Coated with Graphene Oxide Sheets: From Synthesis to Optical Properties and Their Applications as Flame-Retardant Agents

A new method to obtain poly(vinyl chloride) (PVC) spheres, which consists of an interaction between commercial PVC grains and hexyl ethyl cellulose and lauroyl peroxide at a temperature of 60 °C, is reported. The addition of the graphene oxide (GO) sheets dispersed in dimethylformamide to the reaction mixture leads to the generation of composites made of PVC spheres coated with GO sheets. Scanning electron microscopy studies have demonstrated that this method allows for the transformation of PVC grains with sizes between 75 and 227 μm into spheres with sizes varying from 0.7 to 3.5 μm when the GO concentration in the PVC/GO composite mass increases from 0.5 to 5 wt.%. Our studies of Raman scattering and FTIR spectroscopy highlight a series of changes that indicate the appearance of ClCH=CH–, CH₂=CCl–, and/or –CH=CCl– units as a result of PVC partial dehydrogenation. New –COO– and C–OH bonds on the GO sheet surfaces are induced during the preparation of PVC spheres coated with GO sheets. A photoluminescence (PL) band with a maximum at 325 nm is reported to characterize the PVC spheres. A PVC PL quenching process is demonstrated to be induced by the increase in the concentration of the GO sheets in the PVC/GO composite mass. The perspectives regarding the use of this composite as a flame-retardant material are also reported.

New fabrication method for producing reduced graphene oxide flexible electrodes by using a low-power visible laser diode engraving system

The fabrication of bendable electronic devices is a scientific-technological area of very rapid advance in which new materials and fabrication techniques are being continuously developed. In these kinds of devices, the fabrication of flexible conductive electrodes adherent to the substrate is a key factor. Further, eco-friendliness, low cost and fast production are essential requirements for the successful progress of new technologies. In this work, a novel method for obtaining graphene-based flexible electrodes is presented. Conductive films were obtained by means of the visible laser irradiation of graphene oxide layers deposited on polyethylene terephthalate substrates and self-standing membranes sandwiched between glass slides. Despite the low power of the laser system, the numerical simulations indicate the development of temperatures over 1000 K throughout the irradiated material. The laser-induced spatially confined heating leads to the reduction of the graphene oxide material, whereas the glass-based sandwich assembly avoids reoxidation from the surrounding air. By scanning and pixelated modes, reduced graphene oxide electrodes, up to 100 μm in thickness, and with a resistivity as low as 6 × 10^-4 Ωm, were obtained in an easy and versatile way. Proof-of-concept microsupercapacitors and electrochemical sensors were fabricated with this technique, showing promising performance.

Optical Properties of Composites Based on Graphene Oxide and Polystyrene

In this work, new optical properties of composites based on polystyrene (PS) microspheres and graphene oxide (GO) are reported. The radical polymerization of styrene in the presence of benzoyl peroxide, pentane and GO induces the appearance of new ester groups in the PS macromolecular chains remarked through an increase in the absorbance of the infrared (IR) band at 1743 cm^-1. The decrease in the GO concentration in the PS/GO composites mass from 5 wt.% to 0.5 wt.% induces a diminution in the intensities of the D and G Raman bands of GO simultaneous with a down-shift of the D band from 1351 to 1322 cm^-1. These variations correlated with the covalent functionalization of the GO layers with PS. For the first time, the photoluminescent (PL) properties of PS/GO composites are reported. The PS microspheres are characterized by a PL band at 397 nm. Through increasing the GO sheets' concentration in the PS/GO composite mass from 0.5 wt.% to 5 wt.%, a PS PL quenching process is reported. In addition, in the presence of ultraviolet A (UVA) light, a photo-degradation process of the PS/GO composite having the GO concentration equal to 5 wt.% is demonstrated by the PL studies.