Free-Radical Photopolymerization of Acrylonitrile Grafted onto Epoxidized Natural Rubber

The exploitation of epoxidized natural rubber (ENR) in electrochemical applications is approaching its limits because of its poor thermo-mechanical properties. These properties could be improved by chemical and/or physical modification, including grafting and/or crosslinking techniques. In this work, acrylonitrile (ACN) has been successfully grafted onto ENR- 25 by a radical photopolymerization technique. The effect of (ACN to ENR) mole ratios on chemical structure and interaction, thermo-mechanical behaviour and that related to the viscoelastic properties of the polymer was investigated. The existence of the –C≡N functional group at the end-product of ACN-g-ENR is confirmed by infrared (FT-IR) and nuclear magnetic resonance (NMR) analyses. An enhanced grafting efficiency (~57%) was obtained after ACN was grafted onto the isoprene unit of ENR- 25 and showing a significant improvement in thermal stability and dielectric properties. The viscoelastic behaviour of the sample analysis showed an increase of storage modulus up to 150 × 10³ MPa and the temperature of glass transition (T_g) was between −40 and 10 °C. The loss modulus, relaxation process, and tan delta were also described. Overall, the ACN-g-ENR shows a distinctive improvement in characteristics compared to ENR and can be widely used in many applications where natural rubber is used but improved thermal and mechanical properties are required. Likewise, it may also be used in electronic applications, for example, as a polymer electrolyte in batteries or supercapacitor.

Electrochemical double-layer supercapacitor using poly(methyl methacrylate) solid polymer electrolyte

The prime objective of the present article is to develop an efficient supercapacitor based on polymer electrolyte doped with salt. Solution cast technique was adopted to develop a solid polymer electrolyte of polymer poly(methyl methacrylate) (PMMA) as host polymer and salt potassium hydroxide (KOH) as a dopant. Incorporation of salt increases the amorphicity and assisted in conductivity enhancement. Moreover, doping of salt increases the overall conductivity of polymer electrolyte film. Electrochemical impedance spectroscopy reveals the enhancement in conductivity (four orders of magnitude) by salt doping. Fourier transform infrared shows the complexation and composite nature of films. Polarized optical microscopy shows the reduction in crystallinity, which is further confirmed by Differential scanning calorimetry. Fabricated electrochemical double-layer supercapacitor using maximum conducting polymer—salt electrolyte and symmetric carbon nanotubes electrodes shows specific capacitance of 21.86 F g−1.

Improved Stability of Interfacial Energy-Level Alignment in Inverted Planar Perovskite Solar Cells

Even though poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) has been commonly used as a hole extraction layer (HEL) for p-i-n perovskite solar cells (PSCs), the cells' photovoltaic performance deteriorates because of the low and unstable work functions (WFs) of PEDOT:PSS versus those of a perovskite layer. To overcome this drawback, we synthesized a copolymer (P(SS- co-TFPMA)) ionomer consisting of PSS and tetrafluoropropylmethacrylate (TFPMA) as an alternative to conventional PEDOT:PSS. The PEDOT:P(SS- co-TFPMA) copolymer solution and its film exhibited excellent homogeneity and high phase stability compared with a physical mixture of TFPMA with PEDOT:PSS solution. During spin coating, a self-organized conducting PEDOT:P(SS- co-TFPMA) HEL evolved and the topmost PEDOT:P(SS- co-TFPMA) film showed a hydrophobic surface with a higher WF compared to that of the pristine PEDOT:PSS film because of its chemically bonded electron-withdrawing fluorinated functional groups. Interestingly, the WF of the conventional PEDOT:PSS film dramatically deteriorated after being coated with a perovskite layer, whereas the PEDOT:P(SS- co-TFPMA) film represented a relatively small influence. Because of the superior energy-level alignment between the HEL and a perovskite layer even after the contact, the open-circuit voltage, short-circuit current, and fill factor of the inverted planar p-i-n PSCs (IP-PSCs) with PEDOT:P(SS- co-TFPMA) were improved from 0.92 to 0.98 V, 18.96 to 19.66 mA/cm², and 78.96 to 82.43%, respectively, resulting in a 15% improvement in the power conversion efficiency vs that of IP-PSCs with conventional PEDOT:PSS. Moreover, the IP-PSCs with PEDOT:P(SS- co-TFPMA) layer showed not only improved photovoltaic performance but also enhanced device stability due to hydrophobic surface of PEDOT:P(SS- co-TFPMA) film.

Self-Healing, Highly Sensitive Electronic Sensors Enabled by Metal-Ligand Coordination and Hierarchical Structure Design

Electronic sensors capable of capturing mechanical deformation are highly desirable for the next generation of artificial intelligence products. However, it remains a challenge to prepare self-healing, highly sensitive, and cost-efficient sensors for both tiny and large human motion monitoring. Here, a new kind of self-healing, sensitive, and versatile strain sensors has been developed by combining metal-ligand chemistry with hierarchical structure design. Specifically, a self-healing and nanostructured conductive layer is deposited onto a self-healing elastomer substrate cross-linked by metal-ligand coordinate bonds, forming a hierarchically structured sensor. The resultant sensors exhibit high sensitivity, low detection limit (0.05% strain), remarkable self-healing capability, as well as excellent reproducibility. Notably, the self-healed sensors are still capable to precisely capture not only tiny physiological activities (such as speech, swallowing, and coughing) but also large human motions (finger and neck bending, touching). Moreover, harsh treatments, including bending over 50000 times and mechanical washing, could not influence the sensitivity and stability of the self-healed sensors in human motion monitoring. This proposed strategy via alliance of metal-ligand chemistry and hierarchical structure design represents a general approach to manufacturing self-healing, robust sensors, and other electronic devices.