Synthesis and Deposition of Silver Nanowires on Porous Silicon as an Ultraviolet Light Photodetector

The applications of silver nanowires (AgNWs) are clearly relevant to their purity and morphology. Therefore, the synthesis parameters should be precisely adjusted in order to obtain AgNWs with a high aspect ratio. Consequently, controlling the reaction time versus the reaction temperature of the AgNWs is crucial to synthesize AgNWs with a high crystallinity and is important in fabricating optoelectronic devices. In this work, we tracked the morphological alterations of AgNWs during the growth process in order to determine the optimal reaction time and temperature. Thus, here, the UV-Vis absorption spectra were used to investigate how the reaction time varies with the temperature. The reaction was conducted at five different temperatures, 140-180 °C. As a result, an equation was developed to describe the relationship between them and to calculate the reaction time at any given reaction temperature. It was observed that the average diameter of the NWs was temperature-dependent and had a minimum value of 23 nm at a reaction temperature of 150 °C. A significant purification technique was conducted for the final product at a reaction temperature of 150 °C with two different speeds in the centrifuge to remove the heavy and light by-products. Based on these qualities, a AgNWs-based porous Si (AgNWs/P-Si) device was fabricated, and current-time pulsing was achieved using an ultra-violet (UV) irradiation of a 375 nm wavelength at four bias voltages of 1 V, 2 V, 3 V, and 4 V. We obtained a high level of sensitivity and detectivity with the values of 2247.49% and 2.89 × 10¹² Jones, respectively. The photocurrent increased from the μA range in the P-Si to the mA range in the AgNWs/P-Si photodetector due to the featured surface plasmon resonance of the AgNWs compared to the other metals.

Synergistic SERS Enhancement in GaN-Ag Hybrid System toward Label-Free and Multiplexed Detection of Antibiotics in Aqueous Solutions

Noble metal-based surface-enhanced Raman spectroscopy (SERS) has enabled the simple and efficient detection of trace-amount molecules via significant electromagnetic enhancements at hot spots. However, the small Raman cross-section of various analytes forces the use of a Raman reporter for specific surface functionalization, which is time-consuming and limited to low-molecular-weight analytes. To tackle these issues, a hybrid SERS substrate utilizing Ag as plasmonic structures and GaN as charge transfer enhancement centers is presented. By the conformal printing of Ag nanowires onto GaN nanopillars, a highly sensitive SERS substrate with excellent uniformity can be fabricated. As a result, remarkable SERS performance with a substrate enhancement factor of 1.4 × 1011 at 10 fM for rhodamine 6G molecules with minimal spot variations can be realized. Furthermore, quantification and multiplexing capabilities without surface treatments are demonstrated by detecting harmful antibiotics in aqueous solutions. This work paves the way for the development of a highly sensitive SERS substrate by constructing complex metal-semiconductor architectures.

High-yield synthesis of silver nanowires for transparent conducting PET films

Silver nanowires (AgNWs) with ultrahigh purity and high yield were successfully synthesized by employing a modified facile polyol method using PVP as a capping and stabilizing agent. The reaction was carried out at a moderate temperature of 160 °C under mild stirring for about 3 h. The prepared AgNWs exhibited parallel alignment on a large scale and were characterized by UV-vis spectroscopy, scanning electron microscopy (SEM), X-ray diffraction (XRD), and PL spectroscopy. The luminescent AgNWs exhibited red emission, which was accredited to deep holes. The SEM results confirmed the formation of AgNWs of 3.3 to 4.7 µm in length with an average diameter of about 86 nm, that is, the aspect ratio values of the AgNWs exceeded 45. An ink consisting of hydroxyethyl cellulose (HEC) and AgNWs was transferred to polyethylene terephthalate (PET) films by simple mechanical pressing. The PET films retained transparency and flexibility after the ink coating. The maximum transmittance value of as-prepared PET films in the visible region was estimated to be about 92.5% with a sheet resistance value of ca. 20 Ω/sq. This makes the films a potential substitute to commonly used expensive indium tin oxide (ITO) in the field of flexible optoelectronics.

Wearable and washable light/thermal emitting textiles

Electronic textiles (e-textiles) typically comprise fabric substrates with electronic components capable of heating, sensing, lighting and data storage. In this work, we rationally designed and fabricated anisotropic light/thermal emitting e-textiles with great mechanical stability based on a sandwich-structured tri-electrode device. By coating silver nanowire network/thermal insulation bilayer on fabrics, an anisotropic thermal emitter can be realized for smart heat management. By further covering the emissive film and the top electrode on the bilayer, light emitters with desirable patterns and colors are extracted from the top surface via an alternative current derived electroluminescence. Both the light and thermal emitting functions can be operated simultaneously or separately. Particularly, our textiles exhibit reliable heating and lighting performance in water, revealing excellent waterproof feature and washing stability.

Electrical conductivity enhancement of transparent silver nanowire films on temperature-sensitive flexible substrates using intense pulsed ion beam

Silver nanowire (AgNW) networks have attracted particular attention as transparent conductive films (TCF) due to their high conductivity, flexibility, transparency, and large scale processing compatible synthesis. As-prepared AgNW percolating networks typically suffer from high contact resistance, requiring additional post-synthetic processing. In this report, large area irradiation with 200 ns short intense pulsed ion beam (IPIB) was used to anneal and enhance the conductivity of AgNW network, deposited on temperature-sensitive polyethylene terephthalate (PET) substrate. A TCF sheet resistance shows irradiation dose dependence, decreasing by four orders of magnitude and reaching a value of 70 Ω/sq without damaging the polymer substrate, which retained a transparency of 94%. The IPIB irradiation fused AgNW network into the PET substrate, resulting in a great adhesion enhancement. Heat transfer simulations show that the heat originates at the near-surface layer of the TCF and lasts an ultra-short period of time. Obtained experimental and simulation results indicate that the irradiation with IPIBs opens new perspectives in the low-temperature annealing of nanomaterials deposited on temperature-sensitive substrates.

Highly flexible and degradable memory electronics comprised of all-biocompatible materials

Biocompatible materials have received increasing attention as one of the most important building blocks for flexible and transient memories. Herein, a fully biocompatible resistive switching (RS) memory electronic composed of a carbon dot (CD)-polyvinyl pyrrolidone (PVP) nanocomposite and a silver nanowire (Ag NW) network buried in a flexible gelatin film is introduced with promising nonvolatile RS characteristics for flexible and transient memory applications. The fabricated device exhibited a rewritable flash-type memory behavior, such as low operation voltage (≈-1.12 V), high ON/OFF ratio (>10²), long retention time (over 10⁴ s), and small bending radius (15 mm). As a proof of degradability, this transient memory can dissolve completely within 90 s after being immersed into deionized water at 55 °C; it can decompose naturally in soil within 6 days. This fully biocompatible memory electronic paves a novel way for flexible and wearable green electronics.

Modification of Silver Nanowire Coatings with Intense Pulsed Ion Beam for Transparent Heaters

In this report, an improvement of the electrical performance and stability of a silver nanowire (AgNW) transparent conductive coating (TCC) is presented. The TCC stability against oxidation is achieved by coating the AgNWs with a polyvinyl alcohol (PVA) layer. As a result, a UV/ozone treatment has not affected the morphology of the AgNWs network and the PVA protection layer, unlike non-passivated TCC, which showed severe degradation. The irradiation with an intense pulsed ion beam (IPIB) of 200 ns duration and a current density of 30 A/cm² is used to increase the conductivity of the AgNWs network without degradation of the temperature-resistant PVA coating and decrease in the TCC transparency. Simulations have shown that, although the sample temperature reaches high values, the ultra-high heating and cooling rates, together with local annealing, enable the delicate thermal processing. The developed coatings and irradiation strategies are used to prepare and enhance the performance of AgNW-based transparent heaters. A single irradiation pulse increases the operating temperature of the transparent heater from 92 to 160 °C at a technologically relevant voltage of 12 V. The proposed technique shows a great promise in super-fast, low-temperature annealing of devices with temperature-sensitive components.

Simple and Fast High-Yield Synthesis of Silver Nanowires

Silver nanowires (AgNWs) combine high electrical conductivity with low light extinction in the visible and are used in a wide range of applications, from transparent electrodes, to temperature and pressure sensors. The most common strategy for the production of AgNWs is the polyol synthesis, which always leads to the formation of silver nanoparticles as byproducts. These nanoparticles degrade the performance of AgNWs' based devices and have to be eliminated by several purification steps. Here, we report a simple and fast synthesis of AgNWs with minimal formation of byproducts, as confirmed by the spectral purity of the final solution. Our synthetic strategy relies on the use of freshly prepared AgCl and on the minimization of gas evolution inside the reaction vessel. The observed synthetic improvements can be of general validity for the polyol synthesis of metallic nanostructures of different shapes and compositions.

Recyclable and Flexible Dual-Mode Electronics with Light and Heat Management

Realizing multiple functions and sustainable manufacturing within the same electronic device would be highly attractive from a design and fabrication perspective. Here we demonstrate a recyclable dual-mode thin-film device that can perform both light emission and heat management simultaneously. The device is composed of a dissolvable emitting layer sandwiched between two undissolvable conducting films. The vertical multilayered device enables a highly flexible and foldable multicolor electroluminescent emission ranging from yellow or blue to white, and the coplanar monolayered conductor achieves tunable Joule heat temperature setting. By utilizing selective dissolution and artificial reconstruction of each layered component, the parent device shows full recyclability and reconstructability without severe performance degradation after several recycles. The proof-of concept device provides an ideal strategy to construct a multifunctional film system with recyclability and makes a significant contribution to scientific and technological advancement in low-cost sustainable electronics and optoelectronics.

Sustainable and Transparent Fish Gelatin Films for Flexible Electroluminescent Devices

In the past decades, various alternating current electroluminescent (ACEL) devices, especially the flexible ones, have been developed and used in flat panel display, large-scale decorating, logo display lighting, optical signaling, etc. Transparent plastics are usually used as substrates in ACEL devices; however, they are undegradable and may cause serious environmental pollution. Herein, we have developed a flexible transient ACEL device based on transparent fish gelatin (FG) films. The FG films were made from fish scales, which are sustainable, cost-efficient, and eco-friendly. These films could dissolve in water within seconds at 60 °C and degrade completely within 24 days in soil. The transmittance of these FG films was up to 91.1% in the visible spectrum, comparable to that of polyethylene terephthalate (PET) (90.4%). After forming a composite with silver nanowires (Ag NWs), the Ag NWs-FG film showed a transmittance up to 82.3% and a sheet resistance down to 22.4 Ω sq^-1. The fabricated ACEL device based on the Ag NWs-FG film exhibited high flexibility and luminance up to 56.0 cd m^-2. The device could be dissolved in water within 3 min. Our work demonstrates that the sustainable, flexible, and transparent FG films are a promising alternative for green and degradable substrates in the field of flexible electronics, including foldable displays, wearable devices, and health monitoring.

Optoelectronic and Electrothermal Properties of Transparent Conductive Silver Nanowires Films

Silver nanowires (AgNWs) show promise for fabricating flexible transparent conductors owing to their excellent conductivity, high transparency, and good mechanical properties. Here, we present the fabrication of transparent films composed of AgNWs with diameters of 20-30 nm and lengths of 25-30 μm on polyethylene terephthalate substrates and glass slides substrates using the Meyer rod method. We systematically investigated the films' optoelectronic and electrothermal properties. The morphology remained intact when heated at 25-150 °C and the AgNWs film showed high conductivity (17.6-14.3 Ω∙sq-1), excellent transmittance (93.9-91.8%) and low surface roughness values (11.2-14.7 nm). When used as a heater, the transparent AgNW conductive film showed rapid heating at low input voltages owing to a uniform heat distribution across the whole substrate surface. Additionally, the conductivity of the film decreased with increasing bending cycle numbers; however, the film still exhibited a good conductivity and heating performances after repeated bending.

Synthesis and Applications of Silver Nanowires for Transparent Conductive Films

Flexible transparent conductive electrodes (TCEs) are widely applied in flexible electronic devices. Among these electrodes, silver (Ag) nanowires (NWs) have gained considerable interests due to their excellent electrical and optical performances. Ag NWs with a one-dimensional nanostructure have unique characteristics from those of bulk Ag. In past 10 years, researchers have proposed various synthesis methods of Ag NWs, such as ultraviolet irradiation, template method, polyol method, etc. These methods are discussed and summarized in this review, and we conclude that the advantages of the polyol method are the most obvious. This review also provides a more comprehensive description of the polyol method for the synthesis of Ag NWs, and the synthetic factors including AgNO3 concentration, addition of other metal salts and polyvinyl pyrrolidone are thoroughly elaborated. Furthermore, several problems in the fabrication of Ag NWs-based TCEs and related devices are reviewed. The prospects for applications of Ag NWs-based TCE in solar cells, electroluminescence, electrochromic devices, flexible energy storage equipment, thin-film heaters and stretchable devices are discussed and summarized in detail.

An eco-friendly water-assisted polyol method to enhance the aspect ratio of silver nanowires

With water as an eco-friendly heterogeneous nucleation accelerator, silver nanowires (Ag NWs) have been successfully prepared with a high aspect ratio (>1600). The Ag NW-based film exhibits a low sheet resistance of 8.1 Ω sq⁻¹ with a transparency of 81.9% at 550 nm, showing the potential application of electrode materials in polymer solar cells.

Silver nanowires with a high aspect ratio over 1600 were realized through a water-assisted polyol method.

Transient and flexible polymer memristors utilizing full-solution processed polymer nanocomposites

Building transient and flexible memristors is a promising strategy for developing emerging memory technologies. Here, a transient and flexible memristor based on a polymer nanocomposite, with a configuration of silver nanowire (AgNW)/citric acid quantum dot (CA QD)-polyvinyl pyrrolidone (PVP)/AgNW, is fabricated using a full-solution process method. The obtained device exhibits reversible resistive switching behavior and a dynamic random access memory (DRAM) storage feature, with the significant merits of a high ON/OFF ratio, low switching voltage, excellent reproducibility and desirable high flexibility, indicating outstanding memory characteristics such as low misreading, low power operation and low cost potential. Moreover, an operating mechanism of charge trapping/de-trapping of the quantum dots in the polymer matrix has been proposed. Importantly, the memristor can be disintegrated in water within 30 minutes, showing that it is a promising candidate for transient memories. This work paves a new way for potential use of this material in transient electronics, implanted electronics, data storage security and flexible electronic systems.

Five-minute synthesis of silver nanowires and their roll-to-roll processing for large-area organic light emitting diodes

Silver (Ag) nanowires (NWs) are promising building blocks for flexible transparent electrodes, which are key components in fabricating soft electronic devices such as flexible organic light emitting diodes (OLEDs). Typically, Ag NWs have been synthesized using a polyol method, but it still remains a challenge to produce high-aspect-ratio Ag NWs via a simple and rapid process. In this work, we developed a modified polyol method and newly found that the addition of propylene glycol to ethylene glycol-based polyol synthesis facilitated the growth of Ag NWs, allowing the rapid production of long Ag NWs with high aspect ratios of about 2000 in a high yield (∼90%) within 5 min. Transparent electrodes fabricated with our Ag NWs exhibited performance comparable to that of an indium tin oxide-based electrode. With these Ag NWs, we successfully demonstrated the fabrication of a large-area flexible OLED with dimensions of 30 cm × 15 cm using a roll-to-roll process.

Transient Light Emitting Devices Based on Soluble Polymer Composites

Building transient electronics are promising and emerging strategy to alleviate the pollution issues from electronic waste (e-waste). Although a variety of transient devices comprising organic and inorganic materials have been described, transient light emitting devices are still elusive but highly desirable because of the huge amount of lighting and display related consumer electronics. Here we report a simple and efficient fabrication of large-area flexible transient alternating current electroluminescent (ACEL) device through a full-solution processing method. Using transparent flexible AgNW-polymer as both electrodes, the devices exhibit high flexibility and both ends side light emission, with the features of controlled size and patterned structure. By modulating the mass ratio of blue and yellow phosphors, the emission color is changed from white to blue. Impressively, the fabricated ACEL device can be thoroughly dissolved in water within 30 min. Our strategy combining such advances in transient light emitting devices with simple structure, widely used materials, full solution process, and high solubility will demonstrate great potential in resolving the e-waste from abandoned light-emitting products and expand the opportunities for air-stable flexible light emitting devices.

A general strategy for high performance stretchable conductors based on carbon nanotubes and silver nanowires

A general strategy, combining prestraining and embedding, for high performance stretchable conductors based on one-dimensional conductive materials, has been proposed.