Boosting electrochemical water oxidation through replacement of Oh Co sites in cobalt oxide spinel with manganese

Acetate-assisted in situ electrodeposited β-MnO2 for the fabrication of nano-architectonics for non-enzymatic glucose detection

Highly sensitive and low-cost electrocatalytic materials are of great importance for the commercial application of non-enzymatic glucose sensors. Herein, we fabricated a novel one-pot enzyme- and indicator-free method for the colorimetric sensing of blood glucose levels based on the direct redox reaction of β-MnO2/glucose. Owing to the introduction of ammonium acetate and the enhanced oxygen evolution reaction, the higher conductive β-MnO2 nanosheets with the larger surface area were directly grown in situ on the conductive substrate by a linear sweep voltammetry (LSV) electrodeposition method. Besides, owing to the unique tunnel-type pyrolusite MnO2, the electrolyte diffusion was facilitated and reduced the response time in the glucose detection process. Hence, the acetate-assisted MnO2 electrode exhibited a high sensitivity of 461.87 μA M-1 cm-2 toward glucose, a wide detection range from 1.0 μM to 1 mM, and a low detection limit of 0.47 μM while the electrode also maintained excellent selectivity and stability. These results clearly indicate that the new strategy we developed has great potential for practical applications.

Geometric Transformation of Modified Multiwalled Carbon Nanotubes-Based Heterometallic Nanostructured Material: A Model for the Electrochemical Discrimination of Insecticides

Multifunctional carbon-based materials exhibit a large number of unprecedented active sites via an electron transfer process and act as a desired platform for exploring high-performance electroactive material. Herein, we exemplify the holistic design of a heterometallic nanostructured material (MWCNTs@KR-6/Mn/Sn/Pb) formed by the integration of metals (Mn2+, Sn2+, and Pb2+) and a dipodal ligand (KR-6) at the surface of multiwalled carbon nanotubes (MWCNTs). First, MWCNTs@KR-6 was readily synthesized via a noncovalent approach, which was further sequentially doped by Mn2+, Sn2+, and Pb2+ to give MWCNTs@KR-6/Mn/Sn/Pb. The designed material showed excellent electrochemical activity for the discrimination of insecticides belonging to structurally different classes. In contrast to that of the individual building components, both the stability and electrochemical activity of heterometallic nanostructured material were remarkably enhanced, resulting in a magnificent electrochemical performance of the developed material. Hence, the current work reports a comprehensive synthetic approach for MWCNTs@KR-6/Mn/Sn/Pb synthesis by synergizing unique properties of the heterometallic complex with MWCNTs. This work also offers a new insight into the design of multifunctional carbon-based materials for discrimination of different analytes on the basis of their redox potential.

Manganese-Doped Bimetallic (Co,Ni)2P Integrated CoP in N,S Co-Doped Carbon: Unveiling a Compatible Hybrid Electrocatalyst for Overall Water Splitting

Rational design of highly efficient noble-metal-unbound electrodes for hydrogen and oxygen production at increased current density is crucial for robust water-splitting. A facile hydrothermal and room-temperature aging method is presented, followed by chemical vapor deposition (CVD), to create a self-sacrificed hybrid heterostructure electrocatalyst. This hybrid material, (Mn-(Co,Ni)2P/CoP/(N,S)-C), comprises manganese-doped cobalt nickel phosphide (Mn-(Co,Ni)2P) nanofeathers and cobalt phosphide (CoP) nanocubes embedded in a nitrogen and sulfur co-doped carbon matrix (N,S)-C on nickel foam. The catalyst exhibits excellent performance in both the hydrogen evolution reaction (HER; η10 = 61 mV) and oxygen evolution reaction (OER; η10 = 213 mV) due to abundant active sites, high porosity, and enhanced hetero-interface interaction between Mn-(Co2P-Ni2P) CoP, and (N,S)-C supported by significant synergistic effects observed among different phases through density functional theory (DFT) calculations. Impressively, (Mn-(Co,Ni)2P/CoP/(N,S)-C (+,-) shows an extra low cell voltage of 1.49 V@10 mA cm-2. Moreover, the catalyst exhibits remarkable stability at 100 and 300 mA cm-2 when operating as a single stack cell electrolyzer. The superior electrochemical activity is attributed to the enhanced electrode-electrolyte interface among the multiple phases of the hybrid structure.

Atomically dispersed silver atoms incorporated in spinel cobalt oxide (Co3O4) for boosting oxygen evolution reaction

Incorporating noble metal single atoms into lattice of spinel cobalt oxide (Co3O4) is an attractive way to fabricate oxygen evolution reaction (OER) electrocatalysts because of the high activity and economic benefit. The commonly used high valence noble metal dopants such as ruthenium, iridium and rhodium tend to supersede Co3+ at octahedral site of Co3O4 and result in great activity, the origins of admirable activity were also wildly investigated. However, bare explorations on doping noble metal single atom into tetrahedral site of Co3O4 to construct OER catalyst have been reported, corresponding catalytic activity and mechanism remain mystery. Here, a promising structure that tetrahedrally substituent Ag single atom embedded in Co3O4 nanoparticles on the surface of carbon nanotube (Ag-Co3O4/CNT) was presented, and its performance in OER was probed. The high angle annular dark field-scanning transmission electron microscopy (HAADF-STEM) and X-ray absorption spectroscopy (XAS) demonstrate the successful embeddedness of atomical Ag atom in Co3O4 lattice, the resultant electronic interaction is conducive to promote charge transfer for OER. Theoretical calculations further disclose that atomical Ag dopant prefers to replace tetrahedral Co2+ rather than octahedral Co3+. The substitution Ag acts as the active site through Ag-Co bridge and facilitates the desorption process, which improves the turnover frequency (TOF) and boosts the intrinsic activity of Ag-Co3O4/CNT. Benefiting from the essentials above, Ag-Co3O4/CNT displays remarkable activity (236 mV@10 mA cm-2) and robust stability for alkaline OER. This finding offers a potential direction for the design of noble metal single atom involved Co3O4 based OER electrocatalysts.

Synergistic Effects of Co3O4-gC3N4-Coated ZnO Nanoparticles: A Novel Approach for Enhanced Photocatalytic Degradation of Ciprofloxacin and Hydrogen Evolution via Water Splitting

This research evaluates the efficacy of catalysts based on Co3O4-gC3N4@ZnONPs in the degradation of ciprofloxacin (CFX) and the photocatalytic production of H2 through water splitting. The results show that CFX experiences prompt photodegradation, with rates reaching up to 99% within 60 min. Notably, the 5% (Co3O4-gC3N4)@ZnONPs emerged as the most potent catalyst. The recyclability studies of the catalyst revealed a minimal activity loss, approximately 6%, after 15 usage cycles. Using gas chromatography-mass spectrometry (GC-MS) techniques, the by-products of CFX photodegradation were identified, which enabled the determination of the potential degradation pathway and its resultant products. Comprehensive assessments involving photoluminescence, bandgap evaluations, and the study of scavenger reactions revealed a degradation mechanism driven primarily by superoxide radicals. Moreover, the catalysts demonstrated robust performance in H2 photocatalytic production, with some achieving outputs as high as 1407 µmol/hg in the visible spectrum (around 500 nm). Such findings underline the potential of these materials in environmental endeavors, targeting both water purification from organic pollutants and energy applications.

The elemental pegging effect in locally ordered nanocrystallites of high-entropy oxide enables superior lithium storage

High-entropy oxides (HEOs) can be well suited for lithium-ion battery anodes because of their multi-principal synergistic effect and good stability. The appropriate selection and combination of elements play a crucial role in designing conversion-type anode materials with outstanding electrochemical performance. In this study, we have successfully built a single-phase spinel-structured HEO material of (Mn0.23Fe0.23Co0.22Cr0.19Zn0.13)3O4 (HEO-MFCCZ). When the HEO-MFCCZ materials transform into a coexisting state of amorphous and nanocrystalline structures during the cycling process, the inert Zn element can initiate a pegging effect, causing enhanced stability. The transition also introduces many defect sites, effectively reducing the potential barrier for ion transport and accelerating ion transport. The increased electronic and ionic conductivities and pseudocapacitive contribution significantly enhance the rate performance. As a result, a unique and practical approach is provided for developing anode materials for lithium-ion batteries.

A simple microplasma reactor paired with indirect ultrasonication for aqueous phase synthesis of cobalt oxide nanoparticles

Cobalt oxide nanoparticles are widely used owing to their distinct properties such as their larger surface area, enhanced reactivity, and their superior optical, electronic, and magnetic properties when compared to their bulk counterpart. The nanoparticles are preferably synthesized using a bottom-up approach in liquid as it allows the particle size to be more precisely controlled. In this study, we employed microplasma to synthesize Co₃O₄ nanoparticles because it eliminates harmful reducing agents and is efficient and cost-effective. Microplasma reactors are equipped with copper wire electrodes to generate plasma and are simple to configure. The product was characterized using UV-Vis spectroscopy, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FESEM), and transmission electron microscopy (TEM). The experimental parameters that were varied for the synthesis were: with or without stirring, with or without indirect ultrasonication, and with or without capping agents (urea and sucrose). The results showed that the microplasma enabled Co₃O₄ nanoparticles to be successfully synthesized, with particle sizes of 10.9-17.7 nm, depending on the synthesis conditions.

Dimension-Dependent Magnetic Behavior of Manganese-Cysteine Inorganic Complex Nanoparticles

A cysteine-based complex of Mn²⁺ led to the formation of nanoparticles in aqueous medium under ambient conditions. The formation and evolution of the nanoparticles in the medium were followed by ultraviolet-visible light (UV-vis) spectroscopy, circular dichroism, and electron spin resonance spectroscopy that also revealed a first-order process. The magnetic properties of the nanoparticles isolated as solid powders exhibited strong crystallite and particle size dependence. At low crystallite size, as well as particle size, the complex nanoparticles showed superparamagnetic behavior similar to other magnetic inorganic nanoparticles. The magnetic nanoparticles were found to undergo a superparamagnetic to ferromagnetic transition, and then to paramagnetic transition with a gradual increase in either their crystallite size or particle size. The discovery of dimension-dependent magnetic property of inorganic complex nanoparticles may usher in a superior option for tuning the magnetic behavior of nanocrystals, depending on the component ligands and metal ions.

Vacancy effect on the electrocatalytic activity of LaMn1/2Co1/2O3-δ for hydrogen and oxygen evolution reactions

Development of efficient electrocatalysts for water splitting can be a significant step toward green hydrogen generation. In this work, a remarkable enhancement of electrocatalytic properties is achieved through the incorporation of oxygen-vacancies in a perovskite oxide, while maintaining the same structural framework. The oxygen-deficient material La₂MnCoO_6-δ (LaMn_0.5Co_0.5O_3-δ) is isostructural to the parent stoichiometric material, but shows drastically enhanced electrocatalytic properties for both half-reactions of water-splitting, namely hydrogen-evolution and oxygen-evolution reactions, due to the oxygen-vacancies.

Trends and progress in application of cobalt-based materials in catalytic, electrocatalytic, photocatalytic, and photoelectrocatalytic water splitting

There has been a growing interest in water oxidation in recent two decades. Along with that, remarkable discovery of formation of a mysterious catalyst layer upon application of an anodic potential of 1.13 V vs. standard hydrogen electrode (SHE) to an inert indium tin oxide electrode immersed in phosphate buffer containing Co^(II) ions by Nocera et.al, has greatly attracted researchers interest. These researches have oriented in two directions; one focuses on obtaining better understanding of the reported mysterious catalyst layer, further modification, and improved performance, and the second approach is about designing coordination complexes of cobalt and investigating their properties toward the application in water splitting. Although there have been critical debates on true catalysts that are responsible for water oxidation in homogeneous systems of coordination complexes of cobalt, and the case is not totally closed, in this short review, our focus will be mainly on recent major progress and developments in the design and the application of cobalt oxide-based materials in catalytic, electrocatalytic, photocatalytic, and photoelectrocatalytic water oxidation reaction, which have been reported since pioneering report of Nocera in 2008 (Kanan Matthew and Nocera Daniel in Science 321:1072-1075, 2008).

Effective Formation of a Mn-ZIF-67 Nanofibrous Network via Electrospinning: An Active Electrocatalyst for OER in Alkaline Medium

Finding the active center in a bimetallic zeolite imidazolate framework (ZIF) is highly crucial for the electrocatalytic oxygen evolution reaction (OER). In the present study, we constructed a bimetallic ZIF system with cobalt and manganese metal ions and subjected it to an electrospinning technique for feasible fiber formation. The obtained nanofibers delivered a lower overpotential value of 302 mV at a benchmarking current density of 10 mA cm^-2 in an electrocatalytic OER study under alkaline conditions. The obtained Tafel slope and charge-transfer resistance values were 125 mV dec^-1 and 4 Ω, respectively. The kinetics of the reaction is mainly attributed from the ratio of metals (Co and Mn) present in the catalyst. Jahn-Teller distortion reveals that the electrocatalytic active center on the Mn-incorporated ZIF-67 nanofibers (Mn-ZIF-67-NFs) was found to be Mn³⁺ along with the Mn²⁺ and Co²⁺ ions on the octahedral and tetrahedral sites, respectively, where Co²⁺ ions tend to suppress the distortion, which is well supported by density functional theory analysis, molecular orbital study, and magnetic studies.

Mn2O3/Mn3O4-Cu1.5Mn1.5O4 spinel as an efficient Fenton-like catalyst activating persulfate for the degradation of bisphenol A: Superoxide radicals dominate the reaction

In this work, a Mn₂O₃/Mn₃O₄-Cu_1.5Mn_1.5O₄ spinel was fabricated and utilised as a catalyst to activate peroxydisulfate (PDS) leading to degradation of bisphenol A (BPA). The results showed that the system exhibited an excellent turnover frequency (TOF) of 2.7 × 10^-3 s^-1 and high stability. The amount of ion leaching was small and the degree of mineralisation was up to 66.2%. Superoxide radicals (O₂^-) were determined to be the dominant active species in the system. ≡Mn(II) and oxygen vacancies (V_o) were found to be the main active sites at the catalyst surface. The activation of PDS by the spinel catalyst and the reduction of dissolved oxygen both contributed to the production of O₂^- species. The synergistic effect of ≡Cu(I)/≡Cu(II) and ≡Mn(II)/≡Mn(III) redox pairs enabled the reaction to occur continuously. These results suggest the promise of this novel spinel catalyst in the removal of refractory organic compounds due to its excellent performance and stability. The catalyst may thus have great utility for environmental remediation.

Nanoparticles of Mixed-Valence Oxides MnXCO3-XO4 (0 ≤ X ≤ 1) Obtained with Agar-Agar from Red Algae (Rhodophyta) for Oxygen Evolution Reaction

The development of efficient electrocatalysts for the oxygen evolution reaction (OER) is of paramount importance in sustainable water-splitting technology for hydrogen production. In this context, this work reports mixed-valence oxide samples of the Mn_XCo_3-XO₄ type (0 ≤ X ≤ 1) synthesized for the first time by the proteic sol-gel method using Agar-Agar as a polymerizing agent. The powders were calcined at 1173 K, characterized by FESEM, XRD, RAMAN, UV-Vis, FT-IR, VSM, and XPS analyses, and were investigated as electrocatalysts for the oxygen evolution reaction (OER). Through XRD analysis, it was observed that the pure cubic phase was obtained for all samples. The presence of Co³⁺, Co²⁺, Mn²⁺, Mn³⁺, and Mn⁴⁺ was confirmed by X-ray spectroscopy (XPS). Regarding the magnetic measurements, a paramagnetic behavior at 300 K was observed for all samples. As far as OER is concerned, it was investigated in an alkaline medium, where the best overpotential of 299 mV vs. RHE was observed for the sample (MnCo₂O₄), which is a lower value than those of noble metal electrocatalysts in the literature, together with a Tafel slope of 52 mV dec^-1, and excellent electrochemical stability for 15 h. Therefore, the green synthesis method presented in this work showed great potential for obtaining electrocatalysts used in the oxygen evolution reaction for water splitting.

Tuning the Structural and Magnetic Properties in Mixed Cation MnxCo2-xP2S6

The metal thiophosphates (MTP), M₂P₂S₆, are a versatile class of van der Waals materials, which are notable for the possibility of tuning their magnetic properties with the incorporation of different transition-metal cations. Further, they also offer opportunities to probe the independent and synergistic role of the magnetically active cation sublattice when coupled to P₂Q₆ polyhedra. Herein, we report the structural, magnetic, and electronic properties of the series of MTPs, Mn_xCo_2-xP₂S₆ (x = 0.25, 0.5, 1, 1.5, 1.75) synthesized by the P₂S₅ flux method. Structural and elemental analysis indicates a homogeneous stoichiometry in the Mn_xCo_2-xP₂S₆ compounds. We observe that a correlation is apparent between the intensities of specific Raman modes and Raman shifts with respect to the alloying ratio between Mn and Co. Magnetic susceptibility measurements indicate that the alloyed systems adopt an ordered antiferromagnetic (AFM) configuration with a dependence of the Néel temperature on the alloying ratio. A possible magnetic frustration behavior was observed for the composition MnCoP₂S₆ due to magnetic moment compensation as the alloying ratio between Mn and Co approaches parity. Interestingly, mixed oxidation states of the metal cation species are also observed in Mn_xCo_2-xP₂S₆ along with a linear dependence of the work function on the alloying ratio of Mn and Co.

1D Colloidal chains: recent progress from formation to emergent properties and applications

Integrating nanoscale building blocks of low dimensionality (0D; i.e., spheres) into higher dimensional structures endows them and their corresponding materials with emergent properties non-existent or only weakly existent in the individual building blocks. Constructing 1D chains, 2D arrays and 3D superlattices using nanoparticles and colloids therefore continues to be one of the grand goals in colloid and nanomaterial science. Amongst these higher order structures, 1D colloidal chains are of particular interest, as they possess unique anisotropic properties. In recent years, the most relevant advances in 1D colloidal chain research have been made in novel synthetic methodologies and applications. In this review, we first address a comprehensive description of the research progress concerning various synthetic strategies developed to construct 1D colloidal chains. Following this, we highlight the amplified and emergent properties of the resulting materials, originating from the assembly of the individual building blocks and their collective behavior, and discuss relevant applications in advanced materials. In the discussion of synthetic strategies, properties, and applications, particular attention will be paid to overarching concepts, fresh trends, and potential areas of future research. We believe that this comprehensive review will be a driver to guide the interdisciplinary field of 1D colloidal chains, where nanomaterial synthesis, self-assembly, physical property studies, and material applications meet, to a higher level, and open up new research opportunities at the interface of classical disciplines.

An Earth-abundant cobalt based photocatalyst: visible light induced direct (het)arene C-H arylation and CO2 capture

In this work, we have reported a noble metal free heterogeneous photocatalyst to carry out direct (het)arene C-H arylation and solvent-free CO₂ capture via single-electron transfer processes at room temperature and under pressure. The catalytic system comprises a cobalt(III) complex grafted over the silica coated magnetic support for the efficient recovery of the photocatalytic moiety without hampering its light-harvesting capability. The novel Earth-abundant cobalt(III) based photocatalyst possesses various fascinating properties such as high surface area to volume ratios, large pore volume, crystalline behaviour, high metal loading, excellent stability and reusability. The general efficacy of the highly abundant and low-cost cobalt based heterogeneous nanocatalyst was checked for the selective conversion of aryldiazonium salts into synthetically and pharmaceutically significant biaryl motifs under ambient conditions upon irradiation with visible light. The highly efficient photocatalytic conversion of carbon dioxide (CO₂) to a value-added chemical was accomplished under mild reaction conditions with high selectivity, showing the added benefit of operational simplicity.

A heterogeneous cobalt catalyst for C–C bond formation by a borrowing hydrogen strategy

Co–MgO/TiO2 exhibited high activity for α-alkylation of ketones with alcohols through a borrowing hydrogen strategy without the addition of bases which were utilized in reported heterogeneous catalytic systems.

Effect of Heat Treatment on Structural, Magnetic and Electrical Properties of La2FeMnO6

In this study, the effect of heat treatment on the structural, magnetic and electrical properties of La2FeMnO6 prepared via the sol-gel and sintering method were investigated. The heat-treatment conditions, i.e., the calcination temperature (1023 K and 1173 K), sintering temperature and time (1273 K for 1 and 3 h) were carried out. X-ray diffraction (XRD) revealed orthorhombic pnma (62) symmetry without any impurity phase for all samples. X-ray photoelectron spectroscopy confirmed the presence of Fe2+-Fe3+-Fe4+ and Mn3+-Mn4+ mixed states, and lanthanum and oxygen vacancies resulting in various magnetic exchange interactions. Furthermore, the magnetisation hysteresis showed enhanced hysteresis loops accompanied by an increase in magnetisation parameters with calcination temperature. The Raman phonon parameters induced a redshift in the phonon modes, alongside an increase in the intensity and compression of the linewidth, reflecting a decrease in lattice distortion, which was confirmed by XRD. The temperature-dependent conductivity showed that the conduction mechanism is dominated by p-type polaron hopping, and the lowest activation energy was approximately 0.237 ± 0.003 eV for the minimum heat-treatment conditions. These results show that varying heat-treatment conditions can significantly affect the structural, magnetic and electrical properties of the La2FeMnO6 system.

Metallic Co Nanoarray Catalyzes Selective NH3 Production from Electrochemical Nitrate Reduction at Current Densities Exceeding 2 A cm-2

Electrochemical nitrate reduction (NITRR) offers a promising alternative toward nitrogen recycling and ammonia production under ambient conditions, for which highly active and selective electrocatalyst is desired. In this study, metallic cobalt nanoarrays as facilely prepared from the electrochemical reduction of Co(OH)2 nanoarrays (NAs) are demonstrated to exhibit unprecedented NH3 producing capability from catalyzing NITRR. Benefitting from the high intrinsic activity of Co0, intimate contact between active species and conductive substrate and the nanostructure which exposes large number of active sites, the Co-NAs electrode exhibits current density of -2.2 A cm-2 and NH3 production rate of 10.4 mmol h-1 cm-2 at -0.24 V versus RHE under alkaline condition and significantly surpasses reported counterparts. Moreover, the close-to-unity (≥96%) Faradaic efficiency (FE) toward NH3 is achieved over wide application range (potential, NO3 - concentration and pH). Density function theory calculation reveals the optimized adsorption energy of NITRR intermediates on Co surface over Co(OH)2. Furthermore, it is proposed that despite the sluggish kinetics of Volmer step (H2O → *H + *OH) which provides protons in conventional hydrogenation mechanism, the proton-supplying water dissociation process on Co surface is drastically facilitated following a concerted water dissociation-hydrogenation pathway.

Interfacial modification of Co(OH)2/Co3O4 nanosheet heterostructure arrays for the efficient oxygen evolution reaction

The development of efficient, stable and low-cost oxygen evolution reaction (OER) catalysts in anodes is essential for the production of hydrogen resources by electrolyzing water.

Particle size-controlled synthesis of high-performance MnCo-based materials for alkaline OER at fluctuating potentials

Mn and Co containing nanocubes were produced by hydrothermal synthesis. The materials consist of metal spinels and carbonates, where spinels ensure high activity and carbonates contribute to high stability in the oxygen evolution reaction.

A triple-layered PPy@NiCo LDH/FeCo2O4 hybrid crystalline structure with high electron conductivity and abundant interfaces for supercapacitors and oxygen evolution

A PPy@NiCo LDH/FeCo₂O₄ triple-layer hybrid with bi-continuous conductive networks is fabricated via a novel one-step hydrothermal reaction and in situ polymerization.

Cobalt-tungsten diselenide-supported nickel foam as a battery-type positive electrode for an asymmetric supercapacitor device: comparison with various MWSe2 (M = Ni, Cu, Zn, and Mn) on the structural and capacitance characteristics

New exploration in nanomaterial research has been greatly encouraged so as to discover active electrode materials with extraordinary properties and performances. In this report, we demonstrated the synthesis of different transition metal-incorporated MWSe2 (M = Co, Ni, Cu, Zn, and Mn) and studied them using various characterization techniques. Subsequently, the proposed bimetallic chalcogenides were successfully applied as the active electrode materials for pseudocapacitor applications. The results of the electrochemical studies showed that CoWSe2 exhibited a higher specific capacitance of 3309.58 F g-1 at a constant applied current density of 1.35 A g-1, which is 1.07, 1.76, 2.04, 8.7, and 12.28-fold higher than that of NiWSe2, CuWSe2, ZnWSe2, MnWSe2, and pristine WSe2, respectively. The interconnected nanosheet structure with voids facilitates rich active sites for efficient electrolyte uptake and superior charge transfer during the faradaic redox reaction. In addition, the cycle stability of CoWSe2/NF was studied and the retention capacitance of about 82.1% was recorded, which is higher than that of NiWSe2 (60.4%), CuWSe2 (50.12%), ZnWSe2 (46.44%), MnWSe2 (40.12%), and pristine WSe2 (31.2%). Owing to the higher specific capacitance and cycle stability, CoWSe2 was proposed as a battery-type electrode material for the fabrication of an asymmetric device. The fabricated CoWSe2//AC device provided excellent energy density and power density of 182.54 W h kg-1 and 2810.81 W kg-1, respectively, at 3.51 A g-1. Based on these properties, the proposed research and studies can provide a way for the profound development of 2D-layered metal chalcogenides for energy storage applications.

Bioengineered gold nanoparticles from marine seaweed Acanthophora spicifera for pharmaceutical uses: antioxidant, antibacterial, and anticancer activities

In this study, we report a green synthesis of pharmaceutically active gold nanoparticles from marine red alga Acanthophora spicifera by the reduction of chloroauric acid. The formation of A. spicifera-mediated gold nanoparticles (As-AuNPs) was characterized by several analytical techniques. The crystalline and face-centered cubic (fcc) structure were confirmed by X-ray diffraction (XRD) analysis. Electron microscopy results confirmed that As-AuNPs were spherical and the average size of particles was < 20 nm. As-AuNPs hold a significant level of antioxidant activities than A. spicifera extract. As-AuNPs exhibited the highest antibacterial activity against Vibrio harveyi than Staphylococcus aureus at 100 µg/ml. Furthermore, As-AuNPs exhibited the utmost cytotoxicity against human colon adenocarcinoma (HT-29) cells and registered the half-maximal inhibitory concentration (IC₅₀) at 21.86 µg/ml. These findings authenticated that the synthesized As-AuNPs possess a broad spectrum of biological activities, and it can be effectively applied in the field of aquaculture and biomedical application.

A Low-Temperature Molecular Precursor Approach to Copper-Based Nano-Sized Digenite Mineral for Efficient Electrocatalytic Oxygen Evolution Reaction

In the urge of designing noble metal-free and sustainable electrocatalysts for oxygen evolution reaction (OER), herein, a mineral Digenite Cu9 S5 has been prepared from a molecular copper(I) precursor, [{(PyHS)2 CuI (PyHS)}2 ](OTf)2 (1), and utilized as an anode material in electrocatalytic OER for the first time. A hot injection of 1 yielded a pure phase and highly crystalline Cu9 S5 , which was then electrophoretically deposited (EPD) on a highly conducting nickel foam (NF) substrate. When assessed as an electrode for OER, the Cu9 S5 /NF displayed an overpotential of merely 298±3 mV at a current density of 10 mA cm-2 in alkaline media. The overpotential recorded here supersedes the value obtained for the best reported Cu-based as well as the benchmark precious-metal-based RuO2 and IrO2 electrocatalysts. In addition, the choronoamperometric OER indicated the superior stability of Cu9 S5 /NF, rendering its suitability as the sustainable anode material for practical feasibility. The excellent catalytic activity of Cu9 S5 can be attributed to the formation of a crystalline CuO overlayer on the conductive Cu9 S5 that behaves as active species to facilitate OER. This study delivers a distinct molecular precursor approach to produce highly active copper-based catalysts that could be used as an efficient and durable OER electro(pre)catalysts relying on non-precious metals.

Role of precursors mixing sequence on the properties of CoMn2O4 cathode materials and their application in pseudocapacitor

In this study, the effect of oxygen vacancy in the CoMn₂O₄ on pseudocapacitive characteristics was examined, and two tetragonal CoMn₂O₄ spinel compounds with different oxygen vacancy concentrations and morphologies were synthesized by controlling the mixing sequence of the Co and Mn precursors. The mixing sequence was changed; thus, morphologies were changed from spherical nanoparticles to nanoflakes and oxygen vacancies were increased. Electrochemical studies have revealed that tetragonal CoMn₂O₄ spinels with a higher number of oxygen vacancies exhibit a higher specific capacitance of 1709 F g^-1 than those with a lower number of oxygen vacancies, which have a higher specific capacitance of 990 F g^-1. Oxygen vacancies create an active site for oxygen ion intercalation. Therefore, oxidation-reduction reactions occur because of the diffusion of oxygen ions at octahedral/tetrahedral crystal edges. The solid-state asymmetric pseudocapacitor exhibits a maximum energy density of 32 Wh-kg^-1 and an excellent cyclic stability of nearly 100%.

Verchenko V, Shevelkov AV, Driess M. Boosting Water Oxidation through In Situ Electroconversion of Manganese Gallide: An Intermetallic Precursor Approach

For the first time, the manganese gallide (MnGa4 ) served as an intermetallic precursor, which upon in situ electroconversion in alkaline media produced high-performance and long-term-stable MnOx -based electrocatalysts for water oxidation. Unexpectedly, its electrocorrosion (with the concomitant loss of Ga) leads simultaneously to three crystalline types of MnOx minerals with distinct structures and induced defects: birnessite δ-MnO2 , feitknechtite β-MnOOH, and hausmannite α-Mn3 O4 . The abundance and intrinsic stabilization of MnIII /MnIV active sites in the three MnOx phases explains the superior efficiency and durability of the system for electrocatalytic water oxidation. After electrophoretic deposition of the MnGa4 precursor on conductive nickel foam (NF), a low overpotential of 291 mV, comparable to that of precious-metal-based catalysts, could be achieved at a current density of 10 mA cm-2 with a durability of more than five days.

Oxygen Evolution Reaction of Co-Mn-O Electrocatalyst Prepared by Solution Combustion Synthesis

High-performance oxygen evolution reaction (OER) electrocatalysts are needed to produce hydrogen for energy generation through a carbon-free route. In this work, the solution combustion synthesis (SCS) method was employed to synthesize mixed phases of Co- and Mn-based oxides, and the relationships between the crystalline structure and the catalytic properties in the mixed phases were established. The mixed phases of Co- and Mn-based oxides shows promising OER properties, such as acceptable overpotential (450 mV for 10 mA∙cm−2) and Tafel slope (35.8 mV∙dec−1), highlighting the use of the mixed phases of Co- and Mn-based oxides as a new efficient catalysts for water splitting. Electronic structure of the mixed phases of Co- and Mn based oxides is studied in detail to give insight for the origin of high catalytic activities. In addition, excellent long-term stability for OER in alkaline media is achieved for the mixed phase of Co- and Mn based oxides.

Ultrathin carbon coated CoO nanosheet arrays as efficient electrocatalysts for the hydrogen evolution reaction

An ultrathin carbon-coated CoO composite catalyst grown on carbon cloth was developed for efficient alkaline HER.

Structurally Ordered Intermetallic Cobalt Stannide Nanocrystals for High-Performance Electrocatalytic Overall Water-Splitting

The synthesis of structurally ordered non-noble intermetallic cobalt stannide (CoSn₂ ) nanocrystals and their utilization for high-performance electrocatalytic overall water-splitting is presented. The structurally and electronically beneficial properties of the tetragonal CoSn₂ exhibit a considerably low overpotential for the oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) on fluorine-doped tin oxide (FTO) and Ni foam (NF). Loss of Sn from the crystal lattices and oxidation of Co under strongly alkaline conditions furnishes highly disordered amorphous active CoO_x (H), the catalytically active structure for OER. The Co⁰ atoms in the CoSn₂ act as active sites for HER and the presence of Sn provides efficient electrical conductivity. This intermetallic phase is a novel type of cost-effective and competitive bifunctional electrocatalysts and predestinated for overall water-splitting devices: A two-electrode electrolyzer with CoSn₂ on NF delivers a cell voltage of merely 1.55 V at 10 mA cm^-2 maintaining long-term stability.

Metal Organic Framework Derived Materials: Progress and Prospects for the Energy Conversion and Storage

Exploring new materials with high efficiency and durability is the major requirement in the field of sustainable energy conversion and storage systems. Numerous techniques have been developed in last three decades to enhance the efficiency of the catalyst systems, control over the composition, structure, surface area, pore size, and moreover morphology of the particles. In this respect, metal organic framework (MOF) derived catalysts are emerged as the finest materials with tunable properties and activities for the energy conversion and storage. Recently, several nano- or microstructures of metal oxides, chalcogenides, phosphides, nitrides, carbides, alloys, carbon materials, or their hybrids are explored for the electrochemical energy conversion like oxygen evolution, hydrogen evolution, oxygen reduction, or battery materials. Interest on the efficient energy storage system is also growing looking at the practical applications. Though, several reviews are available on the synthesis and application of MOF and MOF derived materials, their applications for the electrochemical energy conversion and storage is totally a new field of research and developed recently. This review focuses on the systematic design of the materials from MOF and control over their inherent properties to enhance the electrochemical performances.

Facile Formation of Nanostructured Manganese Oxide Films as High-Performance Catalysts for the Oxygen Evolution Reaction

The development of inexpensive, earth abundant, and bioinspired oxygen evolution electrocatalysts that are easily accessible and scalable is a principal requirement with regard to the feasibility of water splitting for large-scale chemical energy storage. A unique, versatile, and scalable approach has been developed to fabricate manganese oxide films from single layers to multilayers with a controlled thickness and high reproducibility. The produced MnO_x films are composed of small nanostructures that are assembled closely in the form of porous sponge-like layers. The films were investigated for the electrochemical oxygen evolution reaction in alkaline media and demonstrate a remarkable activity as well as a superior stability of over 60 h. To elucidate the catalytically active species, as well as the striking structural characteristics, the films were further examined in depth by using SEM, TEM, and X-ray photoelectron spectroscopy, as well as quasi in situ extended X-ray absorption fine structure and X-ray absorption near edge structure analysis. The MnO_x catalyst films excel because of a favorably high fraction of Mn³⁺ ions that are retained even after operation at oxidizing potentials. Upon exposure to oxidizing potentials in strongly alkaline aqueous electrolyte, the catalyst material maintains its structural integrity at the nanostructural, morphological, and atomic level.

Coffee-Waste Templating of Metal Ion-Substituted Cobalt Oxides for the Oxygen Evolution Reaction

A facile and scalable method using coffee waste grounds as a hard template has been developed to fabricate nanostructured Co₃ O₄ for the oxygen evolution reaction (OER). Co₃ O₄ incorporating metals with different valences (M/Co=1:4; M=Cu, Ni, Fe, Cr, and W) were also prepared with similar sheet-like structures comprising nanosized crystallites. After detailed characterization by X-ray diffraction, electron microscopy, and nitrogen sorption, the oxides were employed as OER electrocatalysts. Substitution of octahedral and tetrahedral sites of the spinel structure with divalent and trivalent transition metals (Cu, Ni, Fe, and Cr) increased the activity of Co₃ O₄ for the OER, whereas incorporation of hexavalent W led to formation of a second crystal phase and significantly higher electrocatalytic performance. Furthermore, this method is easily scaled up for mass production of Co₃ O₄ with the same nanostructure, which is highly desirable for large-scale application.

Mesoporous manganese phthalocyanine-based materials for electrochemical water oxidation via tailored templating

Electrochemical water splitting using non-noble metals as catalysts is of increasing importance for the future energy sector.