MXene-Derived TiO2/Starbon Nanocomposite as a Remarkable Electrode Material for Coin-Cell Symmetric Supercapacitor

In this study, the synthesis of a MXene (Ti3C2Tx)-derived TiO2/starbon (M-TiO2/Starbon-800 °C) nanocomposite using a facile calcination method is explored. High-temperature exposure transforms layered Ti3C2Tx into rod-like TiO2 and starbon into amorphous carbon. The resulting M-TiO2/Starbon-800 °C nanocomposite exhibits a significantly larger surface area and pore volume compared to its individual components, leading to superior electrochemical performance. In a three-electrode configuration, the nanocomposite achieved a specific capacitance (Csp) of 1352 Fg⁻¹ at 1 Ag⁻¹, while retaining more than 99% of its Csp after 50 000 charge/discharge cycles. Furthermore, when incorporated into a two-electrode symmetric coin cell, it demonstrates a Csp of 115 Fg⁻¹ along with exceptional long cycle life. Moreover, the device shows an energy density (ED) of 51 Whkg-1 and a power density (PD) of 7912 Wkg-1 at 5 Ag-1. The enhanced charge storage is attributed to the formation of a porous structure with a high specific surface area resulting from the interaction between M-TiO2 nanorods and starbon, which facilitates efficient ion penetration.

Titanium dioxide-supported mercury photocatalysts for oxidative removal of hydrogen sulfide from the air using a portable air purification unit

Photocatalytic removal of gaseous hydrogen sulfide (H2S) has been studied through the control of key process variables using a prototype air purifier (AP) fabricated with titanium dioxide (TiO2)-supported mercury. The performance of Hg/TiO2 systems, prepared with different Hg mass proportions over TiO2 (such as 0.1%, 1%, 2%, and 5%), is measured against 5 ppm H2S at 160 L min-1 under UV irradiation. Accordingly, their removal efficiency (RE) values after 360 s are 40.3%, 74.8%, 99.3%, and 99.9%, respectively (relative to 33.5% of AP (TiO2)). An AP with a 2% Hg/TiO2 unit achieves a clean air delivery rate of 32 L min-1 with kinetic reaction rate (r (at 10% RE)) of 0.774 mmol h-1 g-1, quantum yield of 2.19E-02 molecules photon-1, and space-time yield of 1.46E-04 molecules photon-1 mg-1. The superior photocatalytic performance of Hg/TiO2 is supported by superoxide anion and hydroxyl radicals formed in dry air and humid nitrogen (N2) environments, respectively. A density functional theory simulation suggests that the presence of oxygen vacancies should promote the disparities in the electronic structure to subsequently affect the reaction pathways and energetics. The presence of moisture enhances the robust formation of a mercury-OH bond to favorably yield β-mercury sulfide from H2S.

Efficient Decoupled Electrolytic Water Splitting in Acid through Pseudocapacitive TiO2

Water electrolysis remains a key component in the societal transition to green energy. Membrane electrolyzers are the state-of-the-art technology for water electrolysis, relying on 80 °C operation in highly alkaline electrolytes, which is undesirable for many of the myriad end-use cases for electrolytic water splitting. Herein, an alternative water electrolysis process, decoupled electrolysis, is described which performed in mild acidic conditions with excellent efficiencies. Decoupled electrolysis sequentially performs the oxygen evolution reaction (OER) and the hydrogen evolution reaction (HER), at the same catalyst. Here, H+ ions generated from the OER are stored through pseudocapacitive (redox) charge storage, and released to drive the HER. Here, decoupled electrolysis is demonstrated using cheap, abundant, TiO2 for the first time. To achieve decoupled acid electrolysis, ultra-small anatase TiO2 particles (4.5 nm diameter) are prepared. These ultra-small TiO2 particles supported on a carbon felt electrode show a highly electrochemical surface area with a capacitance of 375 F g-1. When these electrodes are tested for decoupled water splitting an overall energy efficiency of 52.4% is observed, with excellent stability over 3000 cycles of testing. This technology can provide a viable alternative to membrane electrolyzers-eliminating the need for highly alkaline electrolytes and elevated temperatures.

Electroactive membrane fusion-liposome for increased electron transfer to enhance radiodynamic therapy

Dynamic therapies have potential in cancer treatments but have limitations in efficiency and penetration depth. Here a membrane-integrated liposome (MIL) is created to coat titanium dioxide (TiO2) nanoparticles to enhance electron transfer and increase radical production under low-dose X-ray irradiation. The exoelectrogenic Shewanella oneidensis MR-1 microorganism presents an innate capability for extracellular electron transfer (EET). An EET-mimicking photocatalytic system is created by coating the TiO2 nanoparticles with the MIL, which significantly enhances superoxide anions generation under low-dose (1 Gy) X-ray activation. The c-type cytochromes-constructed electron channel in the membrane mimics electron transfer to surrounding oxygen. Moreover, the hole transport in the valence band is also observed for water oxidation to produce hydroxyl radicals. The TiO2@MIL system is demonstrated against orthotopic liver tumours in vivo.

Hydrodeoxygenation of Oxygenates Derived from Biomass Pyrolysis Using Titanium Dioxide-Supported Cobalt Catalysts

Bio-oil upgrading to produce biofuels and chemicals has become an attractive topic over the past decade. However, the design of cost- and performance-effective catalysts for commercial-scale production remains a challenge. Herein, commercial titania (TiO2) was used as the support of cobalt (Co)-based catalysts (Co/TiO2) due to its low cost, high availability, and practicability for commercialization in the future. The Co/TiO2 catalysts were made with two different forms of TiO2 (anatase [TiO2-A] and rutile [TiO2-R]) and comparatively evaluated in the hydrodeoxygenation (HDO) of 4-propylguaicol (4PG), a lignin-derived model compound. Both Co/TiO2 catalysts promoted the HDO of 4PG following a similar pathway, but the Co/TiO2-R catalyst exhibited a higher activity in the early stages of the reaction due to the formation of abundant Ti3+ species, as detected by X-ray photoelectron spectroscopy (XPS) and hydrogen-temperature programed reduction (H2-TPR) analyses. On the other hand, the Co/TiO2-A catalyst possessed a higher acidity that enhanced propylcyclohexane production at prolonged reaction times. In terms of reusability, the Co/TiO2-A catalyst showed a higher stability (less Co leaching) and reusability compared to Co/TiO2-R, as confirmed by transmission electron microscopy (TEM) and inductively coupled plasma optical emission spectroscopy (ICP-OES) analyses. The HDO of the real bio-oil derived from pyrolysis of Leucaena leucocephala revealed that the Co/TiO2-A catalyst could convert high oxygenated aromatics (methoxyphenols, dimethoxyphenols, and benzenediols) to phenols and enhanced the phenols content, hinting at its potential to produce green chemicals from bio-feedstock.

Photo-Rechargeable Li-Ion Batteries using TiS2 Cathode

Photo-rechargeable (solar) battery can be considered as an energy harvesting cum storage system, where it can charge the conventional metal-ion battery using light instead of electricity, without having other parasitic reactions. Here a two-electrode lithium-ion solar battery with multifaceted TiS2 -TiO2 hybrid sheets as cathode. The choice of TiS2 -TiO2 electrode ensures the formation of a type II semiconductor heterostructure while the lateral heterostructure geometry ensures high mass/charge transfer and light interactions with the electrode. TiS2 has a higher lithium binding energy (1.6 eV) than TiO2 (1.03 eV), ensuring the possibilities of higher amount of Li-ion insertion to TiS2 and hence the maximum recovery with the photocharging, as further confirmed by the experiments. Apart from the demonstration of solar solid-state batteries, the charging of lithium-ion full cell with light indicates the formation of lithium intercalated graphite compounds, ensuring the charging of the battery without any other parasitic reactions at the electrolyte or electrode-electrolyte interfaces. Possible mechanisms proposed here for the charging and discharging processes of solar batteries, based on the experimental and theoretical results, indicate the potential of such systems in the forthcoming era of renewable energies.

Selective Photooxidation of Valencene and Thymol with Nano-TiO2 and O2 as Oxidant

The selective photocatalytic oxidation with O₂ as oxidant of valencene and thymol was evaluated using nanostructured TiO₂ under UV-Vis radiation at atmospheric conditions. The effect of the morphology and optical properties of TiO₂ nanotubes and aminate nanoparticles was studied. Different scavengers were used to detect the presence of positive holes (h⁺), electrons (e^-), hydroxyl radicals (•OH), and the superoxide radical anion (O₂^-) during the photooxidation reaction. Superoxide anion radical is the main oxidizing specie formed, which is responsible for the selective formation of nootkatone and thymoquinone using aminated TiO₂ nanoparticles under 400 nm radiation.

Hydrothermally synthesized titanium/hydroxyapatite as photoactive and antibacterial biomaterial

The present work investigated hydrothermal synthesis of titanium/hydroxyapatite (Ti/HA) nanocomposite at varied Ti content. The synthesis was performed by coprecipitation method using CaO, ammonium dihydrogen phosphate and titanium oxide chloride precursor with the additional cetyl trimethyl ammonium chloride as templating agent, followed by hydrothermal treatment at 150 °C. The derived materials were characterized by x-ray diffraction, x-ray photoelectron spectroscopy, scanning electron microscopy, transmission electron microscopy analyses. The photocatalytic properties of materials were tested on methyl violet (MV) photocatalytic oxidation, meanwhile the antibacterial testing was performed against Escherichia coli, Staphylococcus aureus, Klebsiella pneumonia, and Streptococcus pyogenes. In addition, cytotoxicity evaluation of the materials as potential biomaterial was also conducted. The results showed that physicochemical character of Ti/HA exhibits exhibit the excellent properties to be photocatalyst along with antibacterial activity. From the detail study of effect of varied titanium content ranging from 5 to 10 %wt., the increasing crystallite size of anatase phase of about 25.81 nm and 38.22 nm for Ti content of 5 and 10 % wt., respectively. In other side, the band gap energy value increases as the increasing Ti content, i.e. the values are 3.08; 3.18; and 3.20 eV for Ti content of 5, 10, 20 % wt., respectively. The band gap energy is correlated with the photocatalytic activity which the highest MV degradation was 96.46% over Ti/HA with 20% wt. of Ti (Ti20/HA). The nanocomposites also express the antibacterial activity with comparable minimum inhibitory concentration (MIC) with other similar Ti/HA nanocomposites. The MIC values of Ti20/HA against E. coli, S. aureus, K. pneumonia, and S. pyogenes are 25; 25; 50 and 50 μg/mL, respectively. In addition, the cytotoxicity test revealed the potency to be a biomimetic material as shown by severe toxicity.

Reduced TiO2with prolonged electron lifetime for improving photocatalytic water reduction activity

The reduction of anatase TiO₂with NaBH₄under argon atmosphere at a high temperature resulted in a longer electron lifetime and a larger electron population. The reduced gray anatase sample with disorder layer showed a higher evolution rate of H₂(130.2μmol h^-1g^-1) compared to pristine TiO₂(24.1μmol h^-1g^-1) in the presence of Pt co-catalyst in an aqueous glucose solution under exposure to ultraviolet light (λ⩽ 400 nm). Ti³⁺and oxygen vacancy defects were proposed to exist in the reduced TiO₂. A continuum tail forms above the valence band edge top as a result of these two defects, which contribute to the lattice disorder. This is presumably also the case with the conduction band, which has a continuum tail composed of mid-gap states as a result of the defects. The Ti³⁺and oxygen vacancy defects operate as shallow traps for photoexcited electrons, thereby preventing recombination. Since the defects are primarily located at the surface, i.e. in the disorder layer, the photoexcited electrons in shallow traps hence become readily available for the reduction of H₃O⁺into H₂. The prolonged electron lifetime increases the photoexcited electron population in the reduced TiO₂, resulting in enhanced water reduction activity.

MXene-derived Ti3C2-Co-TiO2 nanoparticle arrays via cation exchange for highly efficient and stable electrocatalytic oxygen evolution

A cation exchange strategy is proposed to convert layered Ti₃C₂-Na-TiO₂ MXene nanofibers into Ti₃C₂-Co-TiO₂ MXene nanoparticle arrays with open-layered 3D structure and numerous heterogeneous interfaces, which deliver excellent oxygen evolution reaction (OER) activity.

Low-Temperature Synthesis of Cu-Doped Anatase TiO2 Nanostructures via Liquid Phase Deposition Method for Enhanced Photocatalysis

Titanium dioxide (TiO₂) photocatalysis can harness the energy from sunlight, providing a solution to many green- and energy-related problems. In this study, we aimed to produce Cu doped TiO₂ (Cu-TiO₂) structures at a low temperature (~70 °C) under atmospheric pressure based on liquid phase deposition. The products prepared with Cu nitrate exhibited anatase-phase TiO₂ with the presence of Cu, and the particles showed a waxberry-like structure. Changing the Cu nitrate concentration allowed control of the atomic concentration; we confirmed ~1.3 atm.% of Cu ions in the product when we applied 10 mM in the precursor solution. By doping Cu, the light absorption edge shifted to 440 nm (~2.9 eV), and we proved the photocatalytic reaction through action spectral measurement. We observed the decomposition of acetaldehyde into CO₂ on Cu-TiO₂ photocatalysts, which produced optimized improvements in photocatalytic activity at Cu dopant levels between 0.2 and 0.4 atm.%. This study demonstrates that the liquid phase deposition technique can be used for doping metallic ions into TiO₂, which shows promise for preparing novel and unique nanomaterials as visible light photocatalysts.

Synthesis and Photocatalytic Activity for Toluene Removal of CDs/TiO2 - Zeolite Y

Hydrothermally synthesized carbon nanodots (CDs) were impregnated on TiO2. The product (CDs/TiO2) was mechanically mixed with zeolite Y for application in toluene photocatalytic oxidation reaction under UV radiation. Material properties of the samples were investigated by different methods. Toluene vapor was chosen as a typical volatile organic compound to investigate the performance of CDs/TiO2 – zeolite Y photocatalyst when these technological parameters were changed: toluene concentration, gas flow rate, humidity and UV light intensity. In each reaction, only one parameter was changed and the remaining conditions were fixed. The toluene concentrations at the beginning and the end of each reaction were analyzed with the use of gas chromatography (GC). The results of different reaction conditions show the trends for toluene treatment of the CDs/TiO2 – zeolite Y catalyst, thereby providing specific explanations for these trends. The experiments also show that toluene removal is highest when the toluene concentration in the inlet gas is 314 ppmv, the flow rate is 3 L/h, the humidity is 60%, and the catalyst (CDs/TiO2 – zeolite Y composite with 70% zeolite in weight) is illuminated by 4 UV lamps. Copyright © 2022 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 

Integrated Adsorption-Photocatalytic Decontamination of Oxytetracycline from Wastewater Using S-Doped TiO2/WS2/Calcium Alginate Beads

Integrated wastewater treatment processes are needed due to the inefficient removal of emerging pharmaceuticals by single methods. Herein, an adsorbent-photocatalyst integrated material was fabricated by coupling calcium alginate with sulfur-doped TiO2/tungsten disulfide (S-TiO2/WS2/alginate beads) for the removal of oxytetracycline (OTC) from aqueous solution by an integrated adsorption-photocatalysis process. The semiconductor S-TiO2/WS2 hybrid photocatalyst was synthesized with a hydrothermal method, while the integrated adsorbent-photocatalyst S-TiO2/WS2/alginate beads were synthesized by blending S-TiO2/WS2 with sodium alginate using calcium chloride as a precipitating agent. The physicochemical characteristics of S-TiO2/WS2/alginate beads were analyzed using X-ray diffraction , scanning electron microscopy, elemental mapping, X-ray photoelectron spectroscopy, and photoluminescence spectroscopy. The integrated adsorption-photocatalysis process showed enhanced removal from 92.5 to 72%, with a rise in the OTC concentration from 10 to 75 mg/L respectively. The results demonstrated that the adsorption of OTC onto S-TiO2/WS2/alginate beads followed the Elovich kinetic model and Redlich–Peterson isotherm models. The formations of H-bonds, cation bridge bonding, and n-π electron donor-acceptor forces were involved in the adsorption of OCT onto S-TiO2/WS2/alginate beads. In the integrated adsorption-photocatalysis, surface-adsorbed OTC molecules were readily decomposed by the photogenerated active radical species (h⁺, O2•−, and HO•). The persulfate addition to the OTC solution further increased the photocatalysis efficacy due to the formation of additional oxidizing species (SO4•⁻, SO4⁻). Moreover, S-TiO2/WS2/alginate beads showed favorable efficiency and sustainability in OTC removal, approaching 78.6% after five cycles. This integrated adsorption-photocatalysis process offered significant insight into improving efficiency and reusability in water treatment.

Adducing Knowledge Capabilities of Instrumental Techniques Through the Exploration of Heterostructures' Modification Methods

The ongoing evolution of technology has facilitated the global research community to rapidly escalate the constant development of novel advancements in science. At the forefront of such achievements in the field of photocatalysis is the utilisation, and in oftentimes, the adaptation of modern instrumentation to understand photo-physical properties of complex heterostructures. For example, coupling in-situ X-ray Raman scattering spectroscopy for real-time degradation of catalytic materials.

Synthesis of LiDAR-Detectable True Black Core/Shell Nanomaterial and Its Practical Use in LiDAR Applications

Light detection and ranging (LiDAR) sensors utilize a near-infrared (NIR) laser with a wavelength of 905 nm. However, LiDAR sensors have weakness in detecting black or dark-tone materials with light-absorbing properties. In this study, SiO2/black TiO2 core/shell nanoparticles (SBT CSNs) were designed as LiDAR-detectable black materials. The SBT CSNs, with sizes of 140, 170, and 200 nm, were fabricated by a series of Stöber, TTIP sol-gel, and modified NaBH4 reduction methods. These SBT CSNs are detectable by a LiDAR sensor and, owing to their core/shell structure with intrapores on the shell (ca. 2−6 nm), they can effectively function as both color and NIR-reflective materials. Moreover, the LiDAR-detectable SBT CSNs exhibited high NIR reflectance (28.2 R%) in a monolayer system and true blackness (L* < 20), along with ecofriendliness and hydrophilicity, making them highly suitable for use in autonomous vehicles.

Biopolymeric Ni3S4/Ag2S/TiO2/Calcium Alginate Aerogel for the Decontamination of Pharmaceutical Drug and Microbial Pollutants from Wastewater

The ubiquitous presence of pharmaceutical drugs and microbes in the water is leading to the development of drug resistant microbes. Therefore, efficient materials that can remove or inactivate the drug and microbe contaminants are required. In this work, nickel sulfide/calcium alginate (Ni3S4/CA), silver sulfide/calcium alginate (Ag2S/CA), modified titanium dioxide/calcium alginate (TiO2/CA), and Ni3S4/Ag2S/TiO2/calcium alginate (Ni3S4/Ag2S/TiO2/CA) aerogels have been synthesized for the removal of the oxytetracycline (OTC) drug and microbial contaminants from real beverage industry wastewater. The results revealed that Ni3S4/Ag2S/TiO2/CA aerogel is highly efficient for OTC adsorption and inactivation of microbes compared to Ni3S4/CA, Ag2S/CA and TiO2/CA aerogels. The OTC adsorption depends greatly on the solution pH, and optimum OTC removal was observed at pH 6 in its zwitterionic (OTC±) form. The formation of H-bonding and n-π electron donor-acceptors is possible to a considerable extent due to the presence of the double bond benzene ring, oxygen and nitrogen, sulfur-containing functional groups on the OTC molecules, and the Ni3S4/Ag2S/TiO2/CA aerogel. Based on the statistical analysis, root-mean-square deviation (RMSD), chi square (χ2) values, and higher correlation coefficient (R2) values, the Redlich−Peterson isotherm model and Elovich kinetic model are most suited to modelling the OTC adsorption onto Ni3S4/Ag2S/TiO2/CA. The prepared aerogels’ excellent antimicrobial activity is observed in the dark and with solar light irradiation. The zone of inhibition analysis revealed that the antimicrobial activity of the aerogels is in the following order: Ni3S4/Ag2S/TiO2/CA > TiO2/CA > Ag2S/CA > Ni3S4/CA, respectively. Moreover, the antimicrobial results demonstrated that reactive oxygen species, electrons, and active radical species are responsible for growth inhibition and killing of the microbes. These results indicated that Ni3S4/Ag2S/TiO2/CA aerogel is highly efficient in decontaminating pollutants from wastewater.

Synthesis of Titanium Nitride Nanoparticles by Pulsed Laser Ablation in Different Aqueous and Organic Solutions

Owing to a strong photothermal response in the near-IR spectral range and very low toxicity, titanium nitride (TiN) nanoparticles (NPs) synthesized by pulsed laser ablation in liquids (PLAL) present a novel appealing object for photo-induced therapy of cancer, but the properties of these NPs still require detailed investigation. Here, we have elaborated methods of femtosecond laser ablation from the TiN target in a variety of liquid solutions, including acetonitrile, dimethylformamide, acetone, water, and H₂O₂, to synthesize TiN NPs and clarify the effect of liquid type on the composition and properties of the formed NPs. The ablation in all solvents led to the formation of spherical NPs with a mean size depending on the liquid type, while the composition of the NPs ranged from partly oxidized TiN to almost pure TiO₂, which conditioned variations of plasmonic peak in the region of relative tissue transparency (670–700 nm). The degree of NP oxidation depended on the solvent, with much stronger oxidation for NPs prepared in aqueous solutions (especially in H₂O₂), while the ablation in organic solvents resulted in a partial formation of titanium carbides as by-products. The obtained results contribute to better understanding of the processes in reactive PLAL and can be used to design TiN NPs with desired properties for biomedical applications.

Enhanced Fe-TiO2 Solar Photocatalysts on Porous Platforms for Water Purification

In this study, polyethylene glycol-modified titanium dioxide (PEG-modified TiO2) nanopowders were prepared using a fast solvothermal method under microwave irradiation, and without any further calcination processes. These nanopowders were further impregnated on porous polymeric platforms by drop-casting. The effect of adding iron with different molar ratios (1, 2, and 5%) of iron precursor was investigated. The characterization of the produced materials was carried out by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and Raman spectroscopy. Optical characterization of all the materials was also carried out. SEM showed that pure TiO2 and Fe-TiO2 nanostructures presented similar nanosized and spherical particles, which uniformly covered the substrates. From XRD, pure TiO2 anatase was obtained for all nanopowders produced, which was further confirmed by Raman spectroscopy on the impregnated substrates. XPS and UV-VIS absorption spectroscopy emission spectra revealed that the presence of Fe ions on the Fe-TiO2 nanostructures led to the introduction of new intermediate energy levels, as well as defects that contributed to an enhancement in the photocatalytic performance. The photocatalytic results under solar radiation demonstrated increased photocatalytic activity in the presence of the 5% Fe-TiO2 nanostructures (Rhodamine B degradation of 85% after 3.5 h, compared to 74% with pure TiO2 for the same exposure time). The photodegradation rate of RhB dye with the Fe-TiO2 substrate was 1.5-times faster than pure TiO2. Reusability tests were also performed. The approach developed in this work originated novel functionalized photocatalytic platforms, which were revealed to be promising for the removal of organic dyes from wastewater.

Tabrizi B, D’Elia V, Del Gobbo S, Jabbour GE. Microwave-Assisted Non-aqueous and Low-Temperature Synthesis of Titania and Niobium-Doped Titania Nanocrystals and Their Application in Halide Perovskite Solar Cells as Electron Transport Layers

Undoped and Nb-doped TiO₂ nanocrystals are prepared by a microwave-assisted non-aqueous sol-gel method based on a slow alkyl chloride elimination reaction between metal chlorides and benzyl alcohol. Sub-4 nm nanoparticles are grown under microwave irradiation at 80 °C in only 3 h with precise control of growth parameters and yield. The obtained nanocrystals could be conveniently used to cast compact TiO₂ or Nb-doped TiO₂ electron transport layers for application in formamidinium lead iodide-based photovoltaic devices. Niobium doping is found to improve the cell performance by increasing the conductivity and mobility of the electron transport layer. At the same time, a measurable decrease in parasitic light absorption in the low wavelength portion of the spectrum was observed.

Iron/titanium oxide-biochar (Fe2TiO5/BC): A versatile adsorbent/photocatalyst for aqueous Cr(VI), Pb2+, F- and methylene blue

This is the first report of the metal Fe-Ti oxide/biochar (Fe₂TiO₅/BC) composite for simultaneous removal of aqueous Pb²⁺, Cr⁶⁺, F^- and methylene blue (MB). Primary Fe₂TiO₅ nano particles and aggregates were dispersed on a high surface area Douglas fir BC (∼700 m²/g) by a simple chemical co-precipitation method using FeCl₃ and TiO(acac)₂ salts treated by base and heated to 80 °C. This was followed by calcination at 500 °C. This method previously was used without BC to make the neat mixed oxide Fe₂TiO₅, exhibiting a lower energy band gap than TiO₂. Adsorption of Cr(VI), Pb(II), fluoride, and MB on Fe₂TiO₅/BC was studied as a function of pH, equilibrium time, initial adsorbate concentration, and temperature. Adsorption isotherm studies were conducted at 5, 25, and 45 ℃ and kinetics for all four adsorbates followed the pseudo second order model. Maximum Langmuir adsorption capacities for Pb²⁺, Cr⁶⁺, F^- and MB at their initial pH values were 141 (pH 2), 200 (pH 5), 36 (pH 6) and 229 (pH 6) mg/g at 45 ℃ and 114, 180, 26 and 210 mg/g at 25 ℃, respectively. MB was removed from the water on Fe₂TiO₅/BC by synergistic adsorption and photocatalytic degradation at pH 3 and 6 under UV (365 nm) light irradiation. Cr⁶⁺, Pb²⁺, F^-, and MB each exhibited excellent removal capacities in the presence of eight different competitive ions in simulated water samples. The removal mechanisms on Fe₂TiO₅/BC and various competitive ion interactions were proposed. Some iron ion leaching at pH 3 catalyzed Photo-Fenton destruction of MB. Fe₂TiO₅, BC, and Fe₂TiO₅/BC bandgaps were studied to help understand photocatalysis of MB and to advance supported metal oxide photodegradation using smaller energy band gaps than the larger bandgap of TiO₂ for water treatment. A long range goal is to photocatalytically destroy some sorbates with adsorbents to avoid the need for regeneration steps.

Metal oxide nanoparticle-modified ITO electrode for high-performance solution-processed perovskite photodetectors

Low dark current density plays a key role in determining the overall performance of perovskite photodetectors (PPDs). To achieve this goal, a hole transport layer (HTL) on the ITO side and a hole blocking layer (HBL) on the metal electrode side are commonly introduced in PPDs. Unlike traditional approaches, we realized a high-performance solution-processed broadband PPD using metal oxide (MO) nanoparticles (NPs) as the HBL on the ITO electrode and PC₆₁BM as another HBL on the metal electrode side to reduce the device dark current. The PPDs based on TiO₂ and SnO₂ NP-modified layers show similar device performances at −0.5 V: a greater than 10⁵ on/off ratio; over 100 dB linear dynamic range (LDR) under different visible light illumination; around 0.2 A W⁻¹ responsivity (R); greater than 10¹² jones detectivity (D*); and ∼20 μs rise time of the device. The MO NP interfacial layer can significantly suppress charge injection in the dark, while the accumulated photogenerated charges at the interface between the MO layer and the perovskite layer introduce band bending, leading to dramatically increased current under illumination. Therefore, the dark current density of the devices is significantly reduced and the optical gain is drastically enhanced. However, after UV illumination, the dark current of the TiO₂ device dramatically increases while the dark current of the SnO₂ device can stay the same as before since the UV illumination-induced conductivity and barrier height changes in the TiO₂ layer cannot recover after removing the UV irradiation. These results indicate that the TiO₂ NP layer is suitable for making a vis-NIR photodetector, while the SnO₂ NP layer is a good candidate for UV-vis-NIR photodetectors. The facile solution-processed high-performance perovskite photodetector using MO NP-modified ITO is highly compatible with low cost, flexible, and large-area electronics.

PPDs based on TiO₂ and SnO₂ NP layers show similar significantly low dark current density. Due to the UV induced conductivity and barrier height changes in the TiO₂ device after UV illumination the dark current of the device increases, while the SnO₂ device remains the same.

Mechanistic understanding of the increased photoactivity of TiO2 nanosheets upon tantalum doping

Anatase TiO₂ is doped with Ta cations through a hydrothermal route. Based on X-ray photoelectron spectroscopy and X-ray absorption near-edge structure spectroscopy, the Ta dopants exist in the 5+-oxidation state. The oxidation state is insensitive to the Ta loading amount. Extended X-ray absorption fine structure spectroscopy confirms that the local structure around Ta cations is not identical between the Ta-doped samples. The Ta-O distance monotonically increases with the Ta loading amount due to a gradually expanding lattice. The Ta-doped samples show higher activity than pristine TiO₂ for photomineralizing recalcitrant organics. The enhanced photocatalytic activity is proposed to be due to an enhanced population of photoexcited electrons, as probed using light-induced IR absorption spectroscopy, and an extended electron lifetime, as probed using time-resolved microwave conductivity, which are associated with the formation of Ti³⁺ defect states acting as shallow electron traps. The maximum photocatalytic activity is observed for TiO₂ doped with 2 mol% of Ta, which shows enhancement of mineralization efficiency (about 3 times) and enhancement of electron population (up to 20 times), as compared to those of pristine TiO₂. The fundamental question of why a proper metal doping into TiO₂ increases photocatalytic activity is discussed in this study.

Photoluminescence-Based Bioassay With Cysteamine-Capped TiO2 Nanoparticles for the Selective Recognition of N-Acyl Homoserine Lactones

Currently available diagnostic procedures for infections are laborious and time-consuming, resulting in a substantial financial burden by increasing morbidity, increased costs of hospitalization, and mortality. Therefore, innovative approaches to design diagnostic biomarkers are imperative to assist in the rapid and sensitive diagnosis of microbial infections. Acyl homoserine lactones (AHLs) are ubiquitous bacterial signaling molecules that are found to be significantly upregulated in infected sites. In this pioneering work, we have developed a simple photoluminescence-based assay using cysteamine-capped titanium oxide (TiO2) nanoparticles for AHL detection. The PL intensity variation of the oxygen defect state of TiO2 was used for the biosensing measurements. The bioassays were validated using two well-studied AHL molecules (C4-HSL and 3-oxo-C12 HSL) of an important human pathogen, Pseudomonas aeruginosa. The developed system has a maximum relative response of 98%. Furthermore, the efficacy of the system in simulated host urine using an artificial urine medium showed a linear detection range of 10-160 nM. Also, we confirmed the relative response and specificity of the system in detecting AHLs produced by P. aeruginosa in a temporal manner.

Boosting Unassisted Alkaline Solar Water Splitting Using Silicon Photocathode with TiO2 Nanorods Decorated by Edge-Rich MoS2 Nanoplates

To construct a highly efficient photoelectrochemical tandem device with silicon photocathode operating in alkaline conditions, it is desirable to develop stable and active catalysts which enable the photocathode to reliably perform under an alkaline environment. With nanostructured passivation layer and edge-exposed transition metal disulfides, silicon photocathode provides new opportunities for achieving unbiased alkaline solar water splitting. Here, the TiO₂ nanorod arrays decorated by edge-rich MoS₂ nanoplates are elaborately synthesized and deposited on p-Si. The vertically aligned TiO₂ nanorods fully stabilize the Si surface and improve anti-reflectance. Moreover, MoS₂ nanoplates with exposed edge sites provide catalytically active regions resulting in the kinetically favored hydrogen evolution under an alkaline environment. Interfacial energy band bending between p-Si and catalyst layers facilitates the transport of photogenerated electrons under steady-state illumination. Consequently, the MoS₂ nanoplates/TiO₂ nanorods/p-Si photocathode exhibits significantly improved photoelectrochemical-hydrogen evolution reaction (PEC-HER) performance in alkaline media with a high photocurrent density of 10 mA cm^-2 at 0 V versus RHE and high stability. By integrating rationally designed photocathode with earth-abundant Fe₆₀ (NiCo)₃₀ Cr₁₀ anode and perovskite/Si tandem photovoltaic cell, an unassisted alkaline solar water splitting is accomplished with a current density of 5.4 mA cm^-2 corresponding to 6.6% solar-to-hydrogen efficiency, which is the highest among p-Si photocathodes.

Tantalum-Doped TiO2 Prepared by Atomic Layer Deposition and Its Application in Perovskite Solar Cells

Tantalum (Ta)-doped titanium oxide (TiO₂) thin films are grown by plasma enhanced atomic layer deposition (PEALD), and used as both an electron transport layer and hole blocking compact layer of perovskite solar cells. The metal precursors of tantalum ethoxide and titanium isopropoxide are simultaneously injected into the deposition chamber. The Ta content is controlled by the temperature of the metal precursors. The experimental results show that the Ta incorporation introduces oxygen vacancies defects, accompanied by the reduced crystallinity and optical band gap. The PEALD Ta-doped films show a resistivity three orders of magnitude lower than undoped TiO₂, even at a low Ta content (0.8–0.95 at.%). The ultraviolet photoelectron spectroscopy spectra reveal that Ta incorporation leads to a down shift of valance band and conduction positions, and this is helpful for the applications involving band alignment engineering. Finally, the perovskite solar cell with Ta-doped TiO₂ electron transport layer demonstrates significantly improved fill factor and conversion efficiency as compared to that with the undoped TiO₂ layer.

Optical bandgap control in Al2O3/TiO2 heterostructures by plasma enhanced atomic layer deposition: Toward quantizing structures and tailored binary oxides

Atomically thin heterostructures and superlattices are promising candidates for various optoelectronic and photonic applications. Different combinations of Al₂O₃/TiO₂ composites are obtained by plasma enhanced atomic layer deposition (PEALD). Their growth, composition, dispersion relation, and optical bandgap are systematically studied by means of UV/VIS spectrophotometry, spectroscopic ellipsometry (SE), x-ray reflectometry (XRR), scanning transmission electron microscopy(STEM) and x-ray photoelectron spectroscopy (XPS). Besides, an effective medium approximation (EMA) approach is applied to model the heterostructures theoretically. The refractive index and the indirect bandgap of the heterostructures depend on the ratio of the two oxides, while the bandgap is very sensitive to the thicknesses of the barrier and quantum well layers. A large blue shift of the absorption edge from 400 nm to 320 nm is obtained by changing the TiO₂ (quantum well) thickness from ~2 nm to ~0.1 nm separated by ~2 nm of Al₂O₃ (barrier) layers. PEALD unfolds the possibility of achieving optical quantizing effects within complex heterostructures enabling control of their structures down to atomic scale. It enables a path towards atomic scale processing of new 'artificial' materials with desired refractive indices and bandgap combinations by precise control of their compositions.

Enhanced Performance of LiAl0.1Mn1.9O4 Cathode for Li-Ion Battery via TiN Coating

The present work addresses the issues related to the capacity fading of spinel LiMn2O4, such as Mn leaching and Jahn–Teller distortion and suggests an advanced TiN-coated LiAl0.1Mn1.9O4 (LAMO) cathode material as an electrode for lithium-ion batteries. TiN coating layers with the same thickness but a different porosity cover the LiAl0.1Mn1.9O4 electrode via reactive magnetron sputtering, and present promising electrochemical behavior. In contrast with the pristine LiAl0.1Mn1.9O4, the dense TiN-coated LiAl0.1Mn1.9O4 electrode demonstrates a remarkable long-term cycling by reducing the contact area of the electrode/electrolyte interface, resulting in structure stabilization.

Electronic transitions of SWCNTs in comparison to GO on Mn3O4/TiO2 nanocomposites for hydrogen energy generation and solar photocatalysis

The conductivity of metal/metal oxide-doped TiO₂ nanomaterials is enhanced by the incorporation of carbonaceous materials, e.g. single-walled carbon nanotubes (SWCNTs) and graphene oxide (GO).

Improving sensitivity of antimicrobial drug nitrofurazone detection in food and biological samples based on nanostructured anatase-titania sheathed reduced graphene oxide

In this study, we have prepared anatase titanium (IV) oxide warped reduced graphene oxide nanocomposites (TiO₂-rGO NC) using ultrasonic methodology. The morphology of the TiO₂-rGO NC was studied using FESEM and TEM. In addition, XRD, Raman, thermogravimetric analysis (TGA) and XPS are used to analyze the crystallinity and chemical composition of the TiO₂-rGO NC. We have also investigated the electrochemical behavior of the as-prepared NCs with electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), and different pulse voltammetry techniques (DPV). The TiO₂-rGO NC modified electrode shows the lower charge transfer resistance (R _ct ) of 62.87 Ω. Next, the glassy carbon electrode (GCE) was modified with sonochemically prepared TiO₂-rGO NC and used to determine the electrocatalytic reduction of nitrofurazone (NTF). Thus, the proposed sensor established the wider covering range (WCR) of 0.01 to 380 µM and an excellent detection limit of 2.28 nM. Finally, the TiO₂-rGO NC/GCE was applied to determine the NTF in real samples, including crayfish and human blood serum samples, which acquired good found and recovery values.

Titanium Dioxide Thin Films Obtained by Atomic Layer Deposition Promotes Osteoblasts' Viability and Differentiation Potential While Inhibiting Osteoclast Activity-Potential Application for Osteoporotic Bone Regeneration

Atomic layer deposition (ALD) technology has started to attract attention as an efficient method for obtaining bioactive, ultrathin oxide coatings. In this study, using ALD, we have created titanium dioxide (TiO2) layers. The coatings were characterised in terms of physicochemical and biological properties. The chemical composition of coatings, as well as thickness, roughness, wettability, was determined using XPS, XRD, XRR. Cytocompatibillity of ALD TiO2 coatings was accessed applying model of mouse pre-osteoblast cell line MC3T3-E1. The accumulation of transcripts essential for bone metabolism (both mRNA and miRNA) was determined using RT-qPCR. Obtained ALD TiO2 coatings were characterised as amorphous and homogeneous. Cytocompatibility of the layers was expressed by proper morphology and growth pattern of the osteoblasts, as well as their increased viability, proliferative and metabolic activity. Simultaneously, we observed decreased activity of osteoclasts. Obtained coatings promoted expression of Opn, Coll-1, miR-17 and miR-21 in MC3T3-E1 cells. The results are promising in terms of the potential application of TiO2 coatings obtained by ALD in the field of orthopaedics, especially in terms of metabolic- and age-related bone diseases, including osteoporosis.

Using Hot Electrons and Hot Holes for Simultaneous Cocatalyst Deposition on Plasmonic Nanostructures

Hot electrons generated in metal nanoparticles can drive chemical reactions and selectively deposit cocatalyst materials on the plasmonic hotspots, the areas where the decay of plasmons takes place and the hot electrons are created. While hot electrons have been extensively used for nanomaterial formation, the utilization of hot holes for simultaneous cocatalyst deposition has not yet been explored. Herein, we demonstrate that hot holes can drive an oxidation reaction for the deposition of the manganese oxide (MnO_x) cocatalyst on different plasmonic gold (Au) nanostructures on a thin titanium dioxide (TiO₂) layer, excited at their surface plasmon resonance. An 80% correlation between the hot-hole deposition sites and the simulated plasmonic hotspot location is showed when considering the typical hot-hole diffusion length. Simultaneous deposition of more than one cocatalyst is also achieved on one of the investigated plasmonic systems (Au plasmonic nanoislands) through the hot-hole oxidation of a manganese salt and the hot-electron reduction of a platinum precursor in the same solution. These results add more flexibility to the use of hot carriers and open up the way for the design of complex photocatalytic nanostructures.

A Nitrogen- and Self-Doped Titania Coating Enables the On-Demand Release of Free Radical Species

For potential applications such as suppressing the onset of peri-implant infections, a doped titania coating was developed to induce free radical release because of its ability for microbial elimination. The coatability of the sol-gel precursor is robust since the suspension's rheology can be modified to attain uniform and complete surface coverage. The coating is composed of a mixture of anatase and rutile polymorphs doped with nitrogen (N^3-), and it contains substoichiometric Ti²⁺ and Ti³⁺ species. Nitrogen doping results in a 0.4 eV band gap shift, while the defects induce photocurrent generation under visible light excitation up to 650 nm. Greater currents were observed in the nitrogen-doped titania at wavelengths above 450 nm vis-à-vis its (singularly) self-doped counterparts. The (photo)electrochemical behavior and photoactivity of the coating were evaluated by assessing redox species formation in a background aqueous solution. In the absence of any illumination, the coating behaved as an insulator and inhibited the activities of both oxidative and reductive species. On the other hand, under illumination, the coating enhances oxidation processes and inhibits reduction reactions within a near-field region wherein release of free radicals occurs and is constrained (delimited).

Photo-annealed amorphous titanium oxide for perovskite solar cells

Electron selective layers are important to the efficiency, stability and hysteresis of perovskite solar cells. Photo-annealing is a low-cost, roll-to-roll-compatible process that can be applied to the post-treatment fabrication of sol-gel based metal oxide layers. Here, we fabricate an amorphous titanium oxide electron selective layer at a low temperature in a dry atmosphere using a UV light annealing system and compare it with a thermal annealing process. Active oxygen species are created by using UV light to promote hydrolysis and condense the TiO₂ precursor, which removes organic ligands effectively. The photo-annealed TiO₂-based perovskite solar cell has a power conversion efficiency of 19.37% without hysteresis.