Titanium dioxide-supported mercury photocatalysts for oxidative removal of hydrogen sulfide from the air using a portable air purification unit

Photocatalytic removal of gaseous hydrogen sulfide (H2S) has been studied through the control of key process variables using a prototype air purifier (AP) fabricated with titanium dioxide (TiO2)-supported mercury. The performance of Hg/TiO2 systems, prepared with different Hg mass proportions over TiO2 (such as 0.1%, 1%, 2%, and 5%), is measured against 5 ppm H2S at 160 L min-1 under UV irradiation. Accordingly, their removal efficiency (RE) values after 360 s are 40.3%, 74.8%, 99.3%, and 99.9%, respectively (relative to 33.5% of AP (TiO2)). An AP with a 2% Hg/TiO2 unit achieves a clean air delivery rate of 32 L min-1 with kinetic reaction rate (r (at 10% RE)) of 0.774 mmol h-1 g-1, quantum yield of 2.19E-02 molecules photon-1, and space-time yield of 1.46E-04 molecules photon-1 mg-1. The superior photocatalytic performance of Hg/TiO2 is supported by superoxide anion and hydroxyl radicals formed in dry air and humid nitrogen (N2) environments, respectively. A density functional theory simulation suggests that the presence of oxygen vacancies should promote the disparities in the electronic structure to subsequently affect the reaction pathways and energetics. The presence of moisture enhances the robust formation of a mercury-OH bond to favorably yield β-mercury sulfide from H2S.

Graphitized mango seed as an effective 3D anode in batch and continuous mode microbial fuel cells for sustainable wastewater treatment and power generation

Herein, we explored the utilization of graphitized mango seeds as 3D-packed anodes in microbial fuel cells (MFCs) powered by sewage wastewater. Mango seeds were graphitized at different temperatures (800 °C, 900 °C, 1000 °C, and 1100 °C) and their effectiveness as anodes was evaluated. Surface morphology analysis indicated that the proposed anode was characterized by layered branches and micro-sized deep holes, facilitating enhanced biofilm formation and microorganism attachment. Maximum power densities achieved in the MFCs utilizing the mango seed-packed anodes graphitized at 1100 °C and 1000 °C were 2170.8 ± 90 and 1350.6 ± 125 mW m-2, respectively. Furthermore, the weight of the graphitized seed anode demonstrated a positive correlation with the generated power density and cell potential. Specifically, MFCs fabricated with 9 g and 6 g anodes achieved maximum power densities of 2170.8 ± 90 and 1800.5 ± 40 mW m-2, respectively. A continuous mode air cathode MFC employing the proposed graphitized mango anode prepared at 1100 °C and operated at a flow rate of 2 L h-1 generated a stable current density of approximately 12 A m-2 after 15 hours of operation, maintaining its stability for 75 hours. Furthermore, a chemical oxygen demand (COD) removal efficiency of 85% was achieved in an assembled continuous mode MFC. Considering that the proposed MFC was driven by sewage wastewater without the addition of external microorganisms, atmospheric oxygen was used as the electron acceptor through an air cathode mode, agricultural biomass waste was employed for the preparation of the anode, and a higher power density was achieved (2170.8 mW m-2) compared to reported values; it is evident that the proposed graphitized mango seed anode exhibits high efficiency for application in MFCs.

Roles of Heterojunction and Cu Vacancies in the Au@Cu2-xSe for the Enhancement of Electrochemical Nitrogen Reduction Performance

The utilization of hydrogen (H2) as a fuel source is hindered by the limited infrastructure and storage requirements. In contrast, ammonia (NH3) offers a promising solution as a hydrogen carrier due to its high energy density, liquid storage capacity, low cost, and sustainable manufacturing. NH3 has garnered significant attention as a key component in the development of next-generation refueling stations, aligning with the goal of a carbon-free economy. The electrochemical nitrogen reduction reaction (ENRR) enables the production of NH3 from nitrogen (N2) under ambient conditions. However, the low efficiency of the ENRR is limited by challenges such as the electron-stealing hydrogen evolution reaction (HER) and the breaking of the stable N2 triple bond. To address these limitations and enhance ENRR performance, we prepared Au@Cu2-xSe electrocatalysts with a core@shell structure using a seed-mediated growth method and a facile hot-injection method. The catalytic activity was evaluated using both an aqueous electrolyte of KOH solution and a nonaqueous electrolyte consisting of tetrahydrofuran (THF) solvent with lithium perchlorate and ethanol as proton donors. ENRR in both aqueous and nonaqueous electrolytes was facilitated by the synergistic interaction between Au and Cu2-xSe (copper selenide), forming an Ohmic junction between the metal and p-type semiconductor that effectively suppressed the HER. Furthermore, in nonaqueous conditions, the Cu vacancies in the Cu2-xSe layer of Au@Cu2-xSe promoted the formation of lithium nitride (Li3N), leading to improved NH3 production. The synergistic effect of Ohmic junctions and Cu vacancies in Au@Cu2-xSe led to significantly higher ammonia yield and faradaic efficiency (FE) in nonaqueous systems compared to those in aqueous conditions. The maximum NH3 yields were approximately 1.10 and 3.64 μg h-1 cm-2, with the corresponding FE of 2.24 and 67.52% for aqueous and nonaqueous electrolytes, respectively. This study demonstrates an attractive strategy for designing catalysts with increased ENRR activity by effectively engineering vacancies and heterojunctions in Cu-based electrocatalysts in both aqueous and nonaqueous media.

Core-shell TiO2-x-CuyO microspheres for photogeneration of cyclic carbonates under simulated sunlight

Propylene carbonates are important organic solvents and feedstocks for different applications, including synthesis of polymers and Li-batteries. The generation of propylene carbonate utilising anthropogenic CO₂ and renewable solar energy offers an alternative sustainable process with a closed loop carbon cycle. The development of microstructured photocatalysts with desired properties, including high degree of product selectivity, wide range of optical properties, and maximised conversion yield, plays an important role for effective production of propylene carbonate from CO₂. A hierachical hollow core with a double shell of TiO_2-x-Cu₂O-CuO was fabricated using the versatile solvothermal-microwave synthesis method. The fabricated sample revealed effective cascading of photogenerated electrons and holes that promoted the conversion of propylene carbonate (i.e., 1.6 wt%) under 1 Sun irradiation.

Synthesis and Characterization of Carbon and Carbon-Nitrogen Doped Black TiO2 Nanomaterials and Their Application in Sonophotocatalytic Remediation of Treated Agro-Industrial Wastewater

The conventional open ponding system employed for palm oil mill agro-effluent (POME) treatment fails to lower the levels of organic pollutants to the mandatory standard discharge limits. In this work, carbon doped black TiO₂ (CB-TiO₂) and carbon-nitrogen co-doped black TiO₂ (CNB-TiO₂) were synthesized via glycerol assisted sol-gel techniques and employed for the remediation of treated palm oil mill effluent (TPOME). Both the samples were anatase phase, with a crystallite size of 11.09–22.18 nm, lower bandgap of 2.06–2.63 eV, superior visible light absorption ability, and a high surface area of 239.99–347.26 m²/g. The performance of CNB-TiO₂ was higher (51.48%) compared to only (45.72%) CB-TiO₂. Thus, the CNB-TiO₂ is employed in sonophotocatalytic reactions. Sonophotocatalytic process based on CNB-TiO₂, assisted by hydrogen peroxide (H₂O₂), and operated at an ultrasonication (US) frequency of 30 kHz and 40 W power under visible light irradiation proved to be the most efficient for chemical oxygen demand (COD) removal. More than 90% of COD was removed within 60 min of sonophotocatalytic reaction, producing the effluent with the COD concentration well below the stipulated permissible limit of 50 mg/L. The electrical energy required per order of magnitude was estimated to be only 177.59 kWh/m³, indicating extreme viability of the proposed process for the remediation of TPOME.

Enhancing Lithium and Sodium Storage Properties of TiO2(B) Nanobelts by Doping with Nickel and Zinc

Nickel- and zinc-doped TiO2(B) nanobelts were synthesized using a hydrothermal technique. It was found that the incorporation of 5 at.% Ni into bronze TiO2 expanded the unit cell by 4%. Furthermore, Ni dopant induced the 3d energy levels within TiO2(B) band structure and oxygen defects, narrowing the band gap from 3.28 eV (undoped) to 2.70 eV. Oppositely, Zn entered restrictedly into TiO2(B), but nonetheless, improves its electronic properties (Eg is narrowed to 3.21 eV). The conductivity of nickel- (2.24 × 10-8 S·cm-1) and zinc-containing (3.29 × 10-9 S·cm-1) TiO2(B) exceeds that of unmodified TiO2(B) (1.05 × 10-10 S·cm-1). When tested for electrochemical storage, nickel-doped mesoporous TiO2(B) nanobelts exhibited improved electrochemical performance. For lithium batteries, a reversible capacity of 173 mAh·g-1 was reached after 100 cycles at the current load of 50 mA·g-1, whereas, for unmodified and Zn-doped samples, around 140 and 151 mAh·g-1 was obtained. Moreover, Ni doping enhanced the rate capability of TiO2(B) nanobelts (104 mAh·g-1 at a current density of 1.8 A·g-1). In terms of sodium storage, nickel-doped TiO2(B) nanobelts exhibited improved cycling with a stabilized reversible capacity of 97 mAh·g-1 over 50 cycles at the current load of 35 mA·g-1.

Synthesis of TiO2-x/W18O49 hollow double-shell and core-shell microspheres for CO2 photoreduction under visible light

TiO2-x/W18O49 with core-shell or double-shelled hollow microspheres were synthesized through a facile multi-step solvothermal method. The formation of the hollow microspheres with a double-shell was a result of the Kirkendall effect during the solvothermal treatment with concentrated NaOH. The advanced architecture significantly enhanced the electronic properties of TiO2-x/W18O49, improving by more than 30 times the CO2 photoreduction efficiency compared to the pristine W18O49. Operando DRIFTS measurements revealed that the yellow TiO2-x was a preferable CO2 adsorption and conversion site.

Nitrogen-doped TiO2(B) nanobelts enabling enhancement of electronic conductivity and efficiency of lithium-ion storage

To enhance the intrinsic electrical conductivities of TiO₂(B) nanobelts, nitrogen(N)-doped TiO₂(B) nanobelts (N-TNB) were prepared in this study by a facile and cost-effective hydrothermal method using urea as the nitrogen source with TiO₂ (P25) nanoparticles. x-ray photoelectron spectroscopy confirmed that the N-atoms preferentially occupied up to ∼0.516 atom% in the interstitial sites of the N-TNB and the maximum concentration of substituted-N bonds in the N-TNB was ∼0.154 atom%, thereby the total concentration of doped nitrogen elements of ∼0.67 atom% improved the high intrinsic electrical conductivity and ionic diffusivity of the TiO₂(B) nanobelts. The as-prepared N-TNB electrode delivered the highest specific capacity of 133.9 mAh g^-1 in the first cycle, with an exceptional cyclic capacity retention at an ultrafast current rate of 1000 mA g^-1; this is not less than 51% after 500 cycles and represents an excellent rate capability of ∼37 mAh g^-1 at an ultra-high rate of 40 C. These values are among the best ever reported on comparison of the delivered highest discharge capacity of N-TNB at 1000 mA g^-1 and high-rate capabilities of its Li⁺ ion storage with the literature data for N-TNB (∼231.5 mAh g^-1 at a very low current density of 16.75 mA g^-1, ∼0.1 C) of similar materials used in sodium-ion batteries. This implies the potential feasibility of these N-TNB as high-capacity anode materials for next-generation, high-energy-density, electrochemical energy-storage devices.

One-step electrosynthesis of visible light responsive double-walled alloy titanium dioxide nanotube arrays for use in photocatalytic degradation of dibutyl phthalate

Using Ti-6Al-4V (TC4) alloy as a substrate, double-walled alloy titanium dioxide nanotube arrays (DW-ATNTAs) with a special porous inner wall and visible light response are synthesized in situ by an improved anodization method. During the anodization, the V element in the TC4 alloy converts into V₂O₅ which dominates the visible light response of DW-ATNTAs. After 3 h of irradiation with visible light, there is a nearly 97% reduction of dibutyl phthalate (DBP) by DW-ATNTAs in which the degradation kinetic constant is 50 and 7 times higher than that of titanium dioxide nanotube arrays (TNTAs) and alloy titanium dioxide layers (A-TiO₂(plate)), respectively. The richly porous inner wall structure of DW-ATNTAs can provide sufficient vacancies for adsorption and active sites for photocatalytic reaction. Furthermore, the differences in the morphology of the inner and outer walls are attributed to the thicker carbon and fluorine-rich oxide layer (C, F-rich oxide layer) resulting from a longer time that the inner wall spends in contact with the electrolyte during the anodization process. This special porous inner wall structure was formed due to the anti-corrosion properties of the alloy caused by appropriate amounts of V and Al as well as the removal of C and F elements during the calcination process.

HF promoted increased nitrogen doping in TiO2(B) photocatalyst

Increased nitrogen doping in TiO2(B) with obviously enhanced visible light absorption ability was achieved via a facile pretreatment of HF followed by an annealing process in NH3. The optimized samples showed a 2.8 times photocatalytic hydrogen evolution rate and 4.2 times RhB degradation rate compared with the original TiO2(B).

Nitrogen-Doped TiO2-C Composite Nanofibers with High-Capacity and Long-Cycle Life as Anode Materials for Sodium-Ion Batteries

Nitrogen-doped TiO₂-C composite nanofibers (TiO₂/N-C NFs) were manufactured by a convenient and green electrospinning technique in which urea acted as both the nitrogen source and a pore-forming agent. The TiO₂/N-C NFs exhibit a large specific surface area (213.04 m² g^-1) and a suitable nitrogen content (5.37 wt%). The large specific surface area can increase the contribution of the extrinsic pseudocapacitance, which greatly enhances the rate capability. Further, the diffusion coefficient of sodium ions (D _Na+) could be greatly improved by the incorporation of nitrogen atoms. Thus, the TiO₂/N-C NFs display excellent electrochemical properties in Na-ion batteries. A TiO₂/N-C NF anode delivers a high reversible discharge capacity of 265.8 mAh g^-1 at 0.05 A g^-1 and an outstanding long cycling performance even at a high current density (118.1 mAh g^-1) with almost no capacity decay at 5 A g^-1 over 2000 cycles. Therefore, this work sheds light on the application of TiO₂-based materials in sodium-ion batteries.

Nitrogen-Doped TiO2-C Composite Nanofibers with High-Capacity and Long-Cycle Life as Anode Materials for Sodium-Ion Batteries

Nitrogen-doped TiO₂-C composite nanofibers (TiO₂/N-C NFs) were manufactured by a convenient and green electrospinning technique in which urea acted as both the nitrogen source and a pore-forming agent. The TiO₂/N-C NFs exhibit a large specific surface area (213.04 m² g^-1) and a suitable nitrogen content (5.37 wt%). The large specific surface area can increase the contribution of the extrinsic pseudocapacitance, which greatly enhances the rate capability. Further, the diffusion coefficient of sodium ions (D _Na+) could be greatly improved by the incorporation of nitrogen atoms. Thus, the TiO₂/N-C NFs display excellent electrochemical properties in Na-ion batteries. A TiO₂/N-C NF anode delivers a high reversible discharge capacity of 265.8 mAh g^-1 at 0.05 A g^-1 and an outstanding long cycling performance even at a high current density (118.1 mAh g^-1) with almost no capacity decay at 5 A g^-1 over 2000 cycles. Therefore, this work sheds light on the application of TiO₂-based materials in sodium-ion batteries.

Advanced Nanostructured Anode Materials for Sodium-Ion Batteries

Sodium-ion batteries (NIBs), due to the advantages of low cost and relatively high safety, have attracted widespread attention all over the world, making them a promising candidate for large-scale energy storage systems. However, the inherent lower energy density to lithium-ion batteries is the issue that should be further investigated and optimized. Toward the grid-level energy storage applications, designing and discovering appropriate anode materials for NIBs are of great concern. Although many efforts on the improvements and innovations are achieved, several challenges still limit the current requirements of the large-scale application, including low energy/power densities, moderate cycle performance, and the low initial Coulombic efficiency. Advanced nanostructured strategies for anode materials can significantly improve ion or electron transport kinetic performance enhancing the electrochemical properties of battery systems. Herein, this Review intends to provide a comprehensive summary on the progress of nanostructured anode materials for NIBs, where representative examples and corresponding storage mechanisms are discussed. Meanwhile, the potential directions to obtain high-performance anode materials of NIBs are also proposed, which provide references for the further development of advanced anode materials for NIBs.