Light-Triggered Sustainable Defect-Passivation for Stable Perovskite Photovoltaics

The generation of photoinduced defects and freely moving halogen ions is dynamically updated in real time. Accordingly, most reported strategies are static and short-term, which make their improvements in photostability very limited. Therefore, seeking new passivation strategies to match the dynamic characteristics of defect generation is very urgent. Without newly generated defects, a passivation molecule should exist in the configuration that would not become the initiation sites for defect generation. With newly generated defects, the passivation molecule should transfer into the other configuration that possesses the passivation sites. Herein, a classical photoisomeric molecule, spiropyran, is adopted, whose pre- and post-isomeric forms meet the requirements for two different configurations, to realize the state transition once the photoinduced defects appear during subsequent operation and dynamic capture for continuous renewal of defects. Consequently, spiropyrans work as light-triggered and self-healing sustainable passivation sites to realize continuous defect repair. The target devices retain 93% and 99% of their initial power conversion efficiencies after 456 h aging under ultraviolet illumination and 1200 h aging under full-spectrum illumination, respectively. This work provides a novel concept of sustainable passivation strategy to realize continuous defect-passivation and film-healing in perovskite photovoltaics.

Optical Chemosensors based on Spiropyran-Doped Polymer Nanoparticles for Sensing pH of Aqueous Media

Photochromic polymers, which are prepared by the incorporation of photochromic compounds into polymer matrices, show fluorescence emission along with color change under UV light irradiation. Polymer nanoparticles yield high chromic properties at low chromophore loadings, as they have a large surface area to absorb a high level of light irradiation. Particle size is a significant parameter to control optical properties, where the decrease of particle size results in a high light absorption and efficiency of photochromism and fluorescence emission. Reverse atom transfer radical polymerization was used to synthesize methyl methacrylate homopolymer and its copolymers with different comonomers to yield polymers with a narrow molecular weight distribution. Spiropyran was doped to the polymeric nanoparticles during nanoprecipitation to yield photochromic polymer nanoparticles. Particle size below 100 nm for the photochromic nanoparticles was shown by dynamic light scattering. Morphology investigation with microscopic analysis showed spherical morphology for nanoparticles. The photochromic properties of the polymer nanocarriers were studied in both acidic and alkaline media. The results indicated that the pH of the media as well as the copolymer composition significantly affect the optical properties. Therefore, the photochromic polymer nanoparticles could have potential applications as optical pH chemosensors by colorimetric and fluorometric detection mechanisms. The nanoparticles with hydroxyl- or amine-functional groups were shown to be highly efficient for pH chemosensor applications. Finally, photochromic cellulosic papers prepared from the photochromic polymer nanoparticles were highly applicable in the detection of acid vapors.

Recent applications of electrical, centrifugal, and pressurised emerging technologies for fibrous structure engineering in drug delivery, regenerative medicine and theranostics

Advancements in technology and material development in recent years has led to significant breakthroughs in the remit of fiber engineering. Conventional methods such as wet spinning, melt spinning, phase separation and template synthesis have been reported to develop fibrous structures for an array of applications. However, these methods have limitations with respect to processing conditions (e.g. high processing temperatures, shear stresses) and production (e.g. non-continuous fibers). The materials that can be processed using these methods are also limited, deterring their use in practical applications. Producing fibrous structures on a nanometer scale, in sync with the advancements in nanotechnology is another challenge met by these conventional methods. In this review we aim to present a brief overview of conventional methods of fiber fabrication and focus on the emerging fiber engineering techniques namely electrospinning, centrifugal spinning and pressurised gyration. This review will discuss the fundamental principles and factors governing each fabrication method and converge on the applications of the resulting spun fibers; specifically, in the drug delivery remit and in regenerative medicine.

Spiropyran dyes

This article furnishes an introduction to one of the most well-known classes of photochromic colorant. While the properties of spiropyran dyes inspired pioneering efforts to exploit photochromism for industrial applications, their lack of robustness held them back from commercialization. Nevertheless, this type of dye remains at the heart of much of the work to develop light-responsive materials upon which many potential applications in different fields of scientific and technological endeavor depend. The article describes the photochromism, synthesis, and applications of spiropyran colorants with an emphasis on the structural subtype that has attracted the greatest scrutiny. It also acts as a springboard to sources of more detail on these aspects.

Synthesis of Ag@Polycarbazole Nanocomposite using Ferric Acetate as an Oxidant

Silver nanowires and Ag@polycarbazole nanocables have been effectively fabricated. Polyol-reduction and ion adsorption process were used to fabricate pure silver nanowires and Ag@polycarbazole nanocomposite by using an oxidant (iron acetate). Ions of oxidant were adsorbed on the surface of pure silver nanowires to oxidize carbazole monomers for efficient polymerization. The morphology of nanowires and Ag@PCz composite were characterized by using SEM, FT-IR and photoluminescence analysis. The SEM shows the presence of a smooth polymeric sheath. FT-IR and photoluminescence analysis shows dominant peaks that indicate the presence of silver nanowires and polycarbazole (PCz) with a smooth polymeric coating. Nanoparticle analyzer was used to determine z-average and actual size of sample. UV-visible spectrum shows two bands that were dominant at 345 and 410 nm. These are π to π* transitions that indicates the presence of polycarbazole nanocables.

Facile and Scalable Fabrication of Porous Polystyrene Fibers for Oil Removal by Centrifugal Spinning

The demand for an efficient oil sorbent with high sorption capacity, low cost, scalable fabrication, and high selectivity for the cleanup of spreading oil on water is increasingly urgent due to the frequent occurrence of oil spill accidents in seawater all over the world. In this study, porous polystyrene (PS) fibers with high hydrophobicity and superoleophilicity were directly fabricated by a centrifugal spinning method (CS). The effect of solvents, tetrahydrofuran (THF), and dimethylformamide (DMF) on the morphology and porous structure of the polystyrene fibers was evaluated by using scanning electron microscopy and nitrogen adsorption-desorption experiments. The formation mechanism for the porous structure on the fibers was also evaluated. The oil sorption capacities of the PS fibers for silicon oil, pump oil, and vegetable oil were investigated. The highest oil sorption capacity was found in PS fibers fabricated from PS solution with a THF/DMF weight ratio of 1/3, which exhibited the highest specific surface area, pore volume, and porosity. The high productivity and highly porous structure of PS fibers indicate that CS is a promising method to fabricate porous fibers for the cleanup of oil spills.

Centrifugally Spun Recycled PET: Processing and Characterization

Centrifugal spinning, which is a high-productivity fiber fabrication technique, was used to produce a value-added product from recycled poly(ethylene terephthalate) (rPET). In the present study, rPET fibers, with fiber diameters ranging from submicron to micrometer in scale, were fabricated by spinning a solution of rPET in a mixture of dichloromethane and trifluoroacetic acid. The influence of the polymer solution concentration (the viscosity), the rotational speed of the spinneret, and the inner diameter of the needles on the formation and morphology and mechanical properties of the fibers were examined through scanning electron microscopy and using a tensile testing machine. The thermal behaviors of fibrous mats with various average diameters were also investigated through differential scanning calorimetry. The smoothest and smallest fibers, with an average diameter of 619 nm, were generated using an rPET solution of 10 wt % under a rotation speed of 15,000 rpm using needles having an inner diameter of 160 μm. The fibrous mats have an average tensile strength and modulus of 4.3 MPa and 34.4 MPa, respectively. The productivity and the mechanical properties indicate that centrifugal spinning is an effective technique to fabricate high-value product from rPET.

Composite Resin Dosimeters: A New Concept and Design for a Fibrous Color Dosimeter

Polystyrene (PS)-based composite microfibers combined with a photochromic spiropyran dye, 1,3,3-trimethylindolino-6'-nitrobenzopyrylospiran (6-nitro BIPS), and a photostimulable phosphor, europium-doped barium fluorochloride (BaFCl:Eu²⁺), were developed for the detection of X-ray exposure doses on the order of approximately 1 Gy. To produce the PS-based composite microfibers, we employed a forcespinning method that embeds a high concentration of phosphor in PS in a safe, inexpensive, and simple procedure. On the basis of the optimization of the forcespinning process, fibrous color dosimeters with a high radiation dose sensitivity of 1.2-4.4 Gy were fabricated. The color of the dosimeters was found to transition from white to blue in response to X-ray exposure. The optimized fibrous color dosimeter, made from a solution having a PS/6-nitro BIPS/BaFCl:Eu²⁺/C₂Cl₄ ratio of 7.0/0.21/28.0/28.0 (wt %) and produced with a 290 mm distance between the needle and collectors, a 0.34 mm 23 G needle nozzle, and a spinneret rotational rate of 3000 rpm, exhibited sensitivity to a dose as low as 1.2 Gy. To realize practical applications, we manufactured the optimized fibrous color dosimeter into a clothlike color dosimeter. The clothlike color dosimeter was mounted on a stuffed bear, and its coloring behavior was demonstrated upon X-ray exposure. After exposure with X-ray, a blue colored and shaped in the form of the letter "[Formula: see text]" clearly appeared on the surface of the clothlike color dosimeter. The proposed fibrous color dosimeters having excellent workability will be an unprecedented dosimetry and contributed to all industries utilizing radiation dosimeters. This new fibrous "composite resin dosimeter" should be able to replace traditional, wearable, and individual radiation dose monitoring devices, such as film badges.

Inkjet printing and UV-LED curing of photochromic dyes for functional and smart textile applications

Health concerns as a result of harmful UV-rays drive the development of UV-sensors of different kinds. In this research, a UV-responsive smart textile is produced by inkjet printing and UV-LED curing of a specifically designed photochromic ink on PET fabric. This paper focuses on tuning and characterizing the colour performance of a photochromic dye embedded in a UV-curable ink resin. The influence of industrial fabrication parameters on the crosslinking density of the UV-resin and hence on the colour kinetics is investigated. A lower crosslinking density of the UV-resin increases the kinetic switching speed of the photochromic dye molecules upon isomerization. By introducing an extended kinetic model, which defines rate constants k_colouration, k_decay and k_{decolouration}, the colour performance of photochromic textiles can be predicted. Fabrication parameters present a flexible and fast alternative to polymer conjugation to control kinetics of photochromic dyes in a resin. In particular, industrial fabrication parameters during printing and curing of the photochromic ink are used to set the colour yield, colouration/decolouration rates and the durability, which are important characteristics towards the development of a UV-sensor for smart textile applications.

Tuned performance of an inkjet-printed and UV-LED cured smart textile UV-sensor based on a photochromic dye using fabrication parameters.