Selective Depolymerization of Lignin Towards Isolated Phenolic Acids Under Mild Conditions

The selective transformation of lignin to value-added biochemicals (e. g., phenolic acids) in high yields is incredibly challenging due to its structural complexity and many possible reaction pathways. Phenolic acids (PA) are key building blocks for various aromatic polymers, but the isolation of PAs from lignin is below 5 wt.% and requires harsh reaction conditions. Herein, we demonstrate an effective route to selectively convert lignin extracted from sweet sorghum and poplar into isolated PA in a high yield (up to 20 wt.% of lignin) using a low-cost graphene oxide-urea hydrogen peroxide (GO-UHP) catalyst under mild conditions (<120 °C). The lignin conversion yield is up to 95 %, and the remaining low molecular weight organic oils are ready for aviation fuel production to complete lignin utilization. Mechanistic studies demonstrate that pre-acetylation allows the selective depolymerization of lignin to aromatic aldehydes with a decent yield by GO through the Cα activation of β-O-4 cleavage. A urea-hydrogen peroxide (UHP) oxidative process is followed to transform aldehydes in the depolymerized product to PAs by avoiding the undesired Dakin side reaction due to the electron-withdrawing effect of the acetyl group. This study opens a new way to selectively cleave lignin side chains to isolated biochemicals under mild conditions.

On the Oxidative Valorization of Lignin to High-Value Chemicals: A Critical Review of Opportunities and Challenges

The efficient valorization of lignin is crucial if we are to replace current petroleum-based feedstock and establish more sustainable and competitive lignocellulosic biorefineries. Pulp and paper mills and second-generation biorefineries produce large quantities of low-value technical lignin as a by-product, which is often combusted on-site for energy recovery. This Review focuses on the conversion of technical lignins by oxidative depolymerization employing heterogeneous catalysts. It scrutinizes the current literature describing the use of various heterogeneous catalysts in the oxidative depolymerization of lignin and includes a comparison of the methods, catalyst loadings, reaction media, and types of catalyst applied, as well as the reaction products and yields. Furthermore, current techniques for the determination of product yields and product recovery are discussed. Finally, challenges and suggestions for future approaches are outlined.

Physicochemical characteristics of organosolv lignins from different lignocellulosic agricultural wastes

Lignin is a promising alternative to petrochemical precursors for conversion to industrial-needed products. Organosolv lignins were extracted from different agricultural wastes including sugarcane bagasse (BG) and trash (ST), corncob (CC), eucalyptus wood (EW), pararubber woodchip (PRW), and palm wastes (palm kernel cake (PKC), palm fiber (PF), and palm kernel shell (PKS), representing different groups of lignin origins. Physicochemical characteristics of lignins were analyzed by several principal techniques. Most recovered lignin showed high purity of >90 % with trace sugar contamination, while lower purities were found for lignin from palm wastes. Hardwood lignins (EW and PRW) mainly contained guaiacyl (G) and syringyl (S) units with a minor fraction of p-hydroxyphenyl units (H) with high molecular weight, glass transition temperature, phenolic hydroxy group and low aliphatic hydroxy group. Grass-type lignins (BG, ST, CC) and palm lignins (PKC, PF, and PKS) contained three monolignols of H, G, and S units with lower molecular weights and C₅-substituted hydroxy of S unit. Among the grass-type lignins, PKC lignin contained the highest nitrogen and lipophilic components with the lowest molecular weight, thermal stability, and glass transition temperature. This provides insights into properties of organosolv lignin as basis for their further applications in chemical, polymer and material industries.

Oxidative catalytic valorization of industrial lignin into phenolics: Effect of reaction parameters and metal oxides

Oxidative depolymerization of an industrial lignin was performed to study the effect of various metal oxides in oxygen and air atmosphere. CeO₂ exhibited excellent catalytic property, and promoted the production of bio-oil yield up to a maximum of 49 wt% in 10 bar O₂, whereas 31 wt% bio-oil was noticed in atmospheric air. GC-MS analysis of bio-oil showed that high selectivity towards acetosyringone was observed in the presence of air (70.5 area%) as compared to oxygen (48.1 area%). Herein, we have also applied transitional metals (Co, Mn and Cu) doped CeO₂ catalysts. Compared to Cu and Mn, Co metal showed efficient activity that promoted the breaking of labile β-O-4 linkages via the conversion of C_α-OH in to carbonyl group in atmospheric air resulting in the formation of acetosyringone up to 78 area%. Moreover, it exhibited excellent catalytic activity up to four successive cycles. Catalyst has been characterized by XRD, BET, TEM, FT-IR and Raman spectroscopy.

Oxidative Catalytic Fractionation of Lignocellulosic Biomass under Non-alkaline Conditions

Biomass pretreatment methods are commonly used to isolate carbohydrates from biomass, but they often lead to modification, degradation, and/or low yields of lignin. Catalytic fractionation approaches provide a possible solution to these challenges by separating the polymeric sugar and lignin fractions in the presence of a catalyst that promotes cleavage of the lignin into aromatic monomers. Here, we demonstrate an oxidative fractionation method conducted in the presence of a heterogeneous non-precious-metal Co-N-C catalyst and O2 in acetone as the solvent. The process affords a 15 wt% yield of phenolic products bearing aldehydes (vanillin, syringaldehyde) and carboxylic acids (p-hydroxybenzoic acid, vanillic acid, syringic acid), complementing the alkylated phenols obtained from existing reductive catalytic fractionation methods. The oxygenated aromatics derived from this process have appealing features for use in polymer synthesis and/or biological funneling to value-added products, and the non-alkaline conditions associated with this process support preservation of the cellulose, which remains insoluble at reaction conditions and is recovered as a solid.

Supported-Metal Catalysts in Upgrading Lignin to Aromatics by Oxidative Depolymerization

Supported gold and platinum particles on titanium oxide catalysts were evaluated in the oxidative depolymerization of lignins toward high added value aromatics under mild conditions (T: 150 °C, Pair: 20 bar, CNaOH: 10 g/L, 1 h). Kraft and ethanol Organosolv lignins were engaged in the study. Gold catalyst showed a strong tendency to further oxidize aromatics produced from lignin depolymerization to volatile compounds leading to very low yield in target molecules. On the contrary, platinum-based catalysts were allowed to observe enhanced yields that were attributed to its ability to preserve lignin’s substructure during the reaction. A kinetic model was constructed based on the results observed, which allowed us to identify the occurrence of condensation reactions during lignin oxidation and degradation of the produced aromatic compounds as the main limitations to reach high product yields. Insights on lignin oxidation and the catalyst’s role lead through this study would help to reach higher control over lignin valorization.

Catalytic hydrotreatment of kraft lignin into aromatic alcohols over nickel-rhenium supported on niobium oxide catalyst

Direct hydrogenolysis of Kraft lignin was catalyzed over a series of supported Ni or Re catalysts in ethanol solvent. The best results showed that the oil yield of 96.70 wt% was obtained with less char formation at 330 °C for 3 h over 5Ni-5Re/Nb₂O₅ catalyst. Product analysis demonstrated that the monomer yield of 35.41 wt% was given under mild condition, and low-molecular-weight aromatic alcohols were the main component in the liquid products. Ethanol was found to be more effective in H₂ production and facilitated the transformation of phenolic monomers to aromatic chemicals. The results confirmed that the optimal 5Ni-5Re/Nb₂O₅ catalyst had superior oxophilicity and appropriate acid sites, which improved the ability to directly remove the methoxyl and hydroxyl groups of lignin-derived phenolic compounds without aromatic ring hydrogenation. In addition, the temperature, time and solvent effects on the lignin depolymerization were also investigated.

Effective Catalytic Delignification and Fractionation of Lignocellulosic Biomass in Water over Zn3V2O8 Mixed Oxide

The conversion of poplar wood biomass to highly value-added chemicals and molecular building blocks was achieved by using the dispersed mixed oxide Zn₃V₂O₈ (ZVO) in water under 100 kPa of 10% O₂/N₂ at 160, 180, and 200 °C for 4 h. This nanostructured mixed oxide was prepared via the precipitation process and then characterized by several techniques. The results showed that this mixed oxide has interesting catalytic properties and is a versatile catalyst for biomass delignification and lignin and hemicellulose depolymerization. ZVO exhibited high activity on poplar biomass delignification and fractionation (degree of delignification > 97%) and lignin and holocellulose conversion with high yield into aromatic and furan compounds (80 mg/g initial wood at 200 °C), with high selectivities for 5-hydroxymethylfurfural (HMF) (25 mg/g of initial wood), vanillin, and syringaldehyde.

Controlling the growth of nanosized titania via polymer gelation for photocatalytic applications

Nanocrystalline titania was synthesized by a simple, innovative and eco-friendly gelation method by using biopolymers (polysaccharides).

Advances in lignin valorization towards bio-based chemicals and fuels: Lignin biorefinery

Lignin is one of the most promising renewable sources for aromatic hydrocarbons, while effective depolymerization towards its constituent monomers is a particular challenge because of the structural complexity and stability. Intensive research efforts have been directed towards exploiting effective valorization of lignin for the production of bio-based platform chemicals and fuels. The present contribution aims to provide a critical review of key advances in the identification of exact lignin structure subjected to various fractionation technologies and demonstrate the key roles of lignin structures in depolymerization for unique functionalized products. Various technologies (e.g., thermocatalytic approaches, photocatalytic conversion, and mechanochemical depolymerization) are reviewed and evaluated in terms of feasibility and potential for further upgrading. Overall, advances in pristine lignin structure analysis and conversion technologies can facilitate recovery and subsequent utilization of lignin towards tailored commodity chemicals and fungible fuels.