Electrodeposition of indium from the ionic liquid trihexyl(tetradecyl)phosphonium chloride

Scalable Electrodeposition of Liquid Metal from an Acetonitrile-Based Electrolyte for Highly Integrated Stretchable Electronics

The advancement of highly integrated stretchable electronics requires the development of scalable sub-micrometer conductor patterning. Eutectic gallium indium (EGaIn) is an attractive conductor for stretchable electronics, as its liquid metallic character grants it high electrical conductivity upon deformation. However, its high surface tension makes its patterning with sub-micrometer resolution challenging. In this work, this limitation is overcome by way of the electrodeposition of EGaIn. A non-aqueous acetonitrile-based electrolyte that exhibits high electrochemical stability and chemical orthogonality is used. The electrodeposited material leads to low-resistance lines that remain stable upon (repeated) stretching to a 100% strain. Because electrodeposition benefits from the resolution of mature nanofabrication methods used to pattern the base metal, the proposed "bottom-up" approach achieves a record-high density integration of EGaIn regular lines of 300 nm half-pitch on an elastomer substrate by plating on a gold seed layer prepatterned by nanoimprinting. Moreover, vertical integration is enabled by filling high-aspect-ratio vias. This capability is conceptualized by the fabrication of an omnidirectionally stretchable 3D electronic circuit, and demonstrates a soft-electronic analog of the stablished damascene process used to fabricate microchip interconnects. Overall, this work proposes a simple route to address the challenge of metallization in highly integrated (3D) stretchable electronics.

Computational and Experimental Investigation of the Selective Adsorption of Indium/Iron Ions by the Epigallocatechin Gallate Monomer

Selective recovery of indium has been widely studied to improve the resource efficiency of critical metals. However, the interaction and selective adsorption mechanism of indium/iron ions with tannin-based adsorbents is still unclear and hinders further optimization of their selective adsorption performance. In this study, the epigallocatechin gallate (EGCG) monomer, which is the key functional unit of persimmon tannin, was chosen to explore the ability and mechanism of selective separation/extraction of indium from indium-iron mixture solutions. The density functional theory calculation results indicated that the deprotonated EGCG was easier to combine with indium/iron cations than those of un-deprotonated EGCG. Moreover, the interaction of the EGCG-Fe(III) complex was dominated by chelation and electrostatic interaction, while that of the EGCG-In(III) complex was controlled by electrostatic interactions and aromatic ring stacking effects. Furthermore, the calculation of binding energy verified that EGCG exhibited a stronger affinity for Fe(III) than that for In(III) and preferentially adsorbed iron ions in acidic or neutral solutions. Further experimental results were consistent with the theoretical study, which showed that the Freundlich equilibrium isotherm fit the In(III) and Fe(III) adsorption behavior very well, and the Fe(III) adsorption processes followed a pseudo-second-order model. Thermodynamics data revealed that the adsorption of In(III) and Fe(III) onto EGCG was feasible, spontaneous, and endothermic. The adsorption rate of the EGCG monomer for Fe(III) in neutral solution (1:1 mixed solution, pH = 3.0) was 45.7%, 4.3 times that of In(III) (10.7%). This study provides an in-depth understanding of the relationship between the structure of EGCG and the selective adsorption capacity at the molecular level and provides theoretical guidance for further optimization of the selective adsorption performance of structurally similar tannin-based adsorbents.

Electrodeposition of Indium from an Ionic Liquid Investigated by In Situ Electrochemical XPS

The electrochemical behavior and electrodeposition of indium in an electrolyte composed of 0.1 mol/L InCl3 in 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)amide ([Py1,4]TFSI) on a gold electrode were investigated. The cyclic voltammogram revealed several reduction and oxidation peaks, indicating a complex electrochemical behavior. In the cathodic regime, with the formation of an In-Au alloy, the reduction of In(III) to In(I) and of In(I) to In(0) takes place. In situ electrochemical X-ray photoelectron spectroscopy (XPS) was employed to investigate the reduction process by monitoring the oxidation states of the components during the cathodic polarization of 0.1 mol/L InCl3/[Py1,4]TFSI on a gold working electrode under ultra-high vacuum (UHV) conditions. The core electron binding energies of the IL components (C 1s, O 1s, F 1s, N 1s, and S 2p) shift almost linearly to more negative values as a function of the applied cell voltage. At −2.0 V versus Pt-quasi reference, In(I) was identified as the intermediate species during the reduction process. In the anodic regime, a strong increase in the pressure in the XPS chamber was recorded at a cell voltage of more than −0.5 V versus Pt quasi reference, which indicated, in addition to the oxidation reactions of In species, that the oxidation of Cl− occurs. Ex situ XPS and XRD results revealed the formation of metallic In and of an In-Au alloy.

Ionometallurgical Step-Electrodeposition of Zinc and Lead and its Application in a Cycling-Stable High-Voltage Zinc-Graphite Battery

Ionometallurgy is a new development aiming at the sustainable low-temperature conversion of naturally occurring metal ores and minerals to their metals or valuable chemicals in ionic liquids (ILs) or deep eutectic solvents. The IL betainium bis((trifluoromethyl)sulfonyl)imide, [Hbet][NTf₂ ], is especially suited for this process due to its redox-stability and specific-functionalization. The potentiostatic electrodeposition of zinc and lead starting directly from ZnO and PbO, which dissolve in [Hbet][NTf₂ ] in high concentrations is reported. The initial reduction potentials of zinc(II) and lead(II) are about -1.5 and -1.0 V, respectively. The ionic conductivity of the solution of ZnO in [Hbet][NTf₂ ] is measured and the effect of various temperatures and potentials on the morphology of the deposited material is explored. The IL proves to be stable under the chosen conditions. From IL-solutions, where ZnO, PbO, and MgO have been dissolved, metallic Zn and Pb are deposited under potentiostatic control either consecutively by step-electrodeposition or together in a co-electrodeposition. Using the method, Zn is also deposited on 3D copper foam and assembles into high-voltage zinc-graphite battery. It exhibits a working-voltage up to 2.7 V, an output midpoint discharge-voltage of up to 2.16 V, up to 98.6% capacity-retention after 150 cycles, and good rate performance.

Oxidative Dissolution of Metals in Organic Solvents

Dissolution of metals in organic solvents is relevant to various application fields, such as metal extraction from ores or secondary resources, surface etching or polishing of metals, direct synthesis of organometallic compounds, and separation of metals from other compounds. Organic solvents for dissolution of metals can offer a solution when aqueous systems fail, such as separation of metals from metal oxides, because both the metal and metal oxide could codissolve in aqueous acidic solutions. This review critically discusses organic media (conventional molecular organic solvents, ionic liquids, deep-eutectic solvents and supercritical carbon dioxide) for oxidative dissolution of metals in different application areas. The reaction mechanisms of dissolution processes are discussed for various lixiviant systems which generally consist of oxidizing agents, chelating agents, and solvents. Different oxidizing agents for dissolution of metals are reviewed such as halogens, halogenated organics, donor-acceptor electron-transfer systems, polyhalide ionic liquids, and others. Both chemical and electrochemical processes are included. The review can guide researchers to develop more efficient, economic, and environmentally friendly processes for dissolution of metals in their elemental state.

Indium electrodeposition from indium(iii) methanesulfonate in DMSO

The electrochemical behavior and electrodeposition of indium was investigated at 26 °C and 160 °C from a solution composed of indium(iii) methanesulfonate and dimethylsulfoxide (DMSO). Indium(iii) methanesulfonate was synthesized from indium(iii) oxide and methanesulfonic acid (MSA). Cyclic voltammetry, quartz crystal microbalance measurements and rotating ring disk electrode experiments indicated that reduction of indium(iii) to both indium(i) and indium(0) occurs. Yet, reduction to metallic indium was found to be the predominant process. Deposited indium could be stripped to indium(i). This unstable species disproportionated to indium(iii) and indium(0), leading to the formation of micron-sized metallic indium particles in the electrolyte. At 26 °C, indium deposited on glassy carbon as smooth, flat films whereas at 160 °C, it deposits as droplets.

Potential Application of Ionic Liquids for Electrodeposition of the Material Targets for Production of Diagnostic Radioisotopes

An overview of the reported electrochemistry studies on the chemistry of the element for targets for isotope production in ionic liquids (ILs) is provided. The majority of investigations have been dedicated to two aspects of the reactive element chemistry. The first part of this review presents description of the cyclotron targets properties, especially physicochemical characterization of irradiated elements. The second part is devoted to description of the electrodeposition procedures leading to obtain elements or their alloys coatings (e.g., nickel, uranium) as the targets for cyclotron and reactor generation of the radioisotopes. This review provides an evaluation of the role ILs can have in the production of isotopes.

Non-aqueous solvent extraction of indium from an ethylene glycol feed solution by the ionic liquid Cyphos IL 101: speciation study and continuous counter-current process in mixer-settlers

A solvometallurgical process for the separation of indium(iii) and zinc(ii) from ethylene glycol solutions using the ionic liquid extractants Cyphos IL 101 and Aliquat 336 in an aromatic diluent has been investigated. The speciation of indium(iii) in the two immiscible organic phases was investigated by Raman spectroscopy, infrared spectroscopy, EXAFS and 115In NMR spectroscopy. At low LiCl concentrations in ethylene glycol, the bridging (InCl3)2(EG)3 or mononuclear (InCl3)(EG)2 complex is proposed. At higher lithium chloride concentrations, the first coordination sphere changes to two oxygen atoms from one bidentate ethylene glycol ligand and four chloride anions ([In(EG)Cl4]-). In the less polar phase, indium(iii) is present as a tetrahedral [InCl4]- complex independent of the LiCl concentration. After the number of theoretical stages had been determined using a McCabe-Thiele diagram for extraction by Cyphos IL 101, the extraction and scrubbing processes were performed in lab-scale mixer-settlers to test the feasibility of working in continuous mode. Indium(iii) was extracted quantitatively in four stages, with 19% co-extraction of zinc(ii). The co-extracted zinc(ii) was scrubbed selectively in six stages using an indium(iii) scrub solution. Indium(iii) was recovered from the loaded less polar organic phase as indium(iii) hydroxide (98.5%) by precipitation stripping with an aqueous NaOH solution.

Effect of Ionic Composition on Physicochemical Properties of Mono-Ether Functional Ionic Liquids

Tunable properties prompt the development of different "tailor-made" functional ionic liquids (FILs) for specific tasks. FILs with an ether group are good solvents for many organic compounds and enzymatic reactions. However, ionic composition influences the solubility by affecting the physiochemical properties of these FILs. To address the structure effect, a series of novel FILs with a mono-ether group (ME) based on imidazole were prepared through cationic functionalization and anionic exchange reactions, and characterized by NMR, mass spectroscopy, and Thermogravimetric analysis (TGA). The effect of ionic composition (cationic structure and anions) on density, viscosity, ionic conductivity, electrochemical window, and thermal properties of these ME-FILs were systematically investigated. In general, the viscosity and heat capacity increases with the bigger cationic volume of ME-FILs; in particular, the 2-alkyl substitution of imidazolium enhances the viscosity remarkably, whereas the density and conductivity decrease on the condition of the same [NTf₂]^- anion; For these ME-FILs with the same cations, the density follows the order of [NTf₂]^- > [PF₆]^- > [BF₄]^-. The viscosity follows the order of [PF₆]^- > [BF₄]^- > [NTf₂]^-. Ion conductivity follows the order of [NTf₂]^- ≈ [BF₄]^- > [PF₆]^-. It is noted that the dynamic density has a good linear relationship with the temperature, and the slopes are the same for all ME-FILs. Furthermore, these ME-FILs have broad electrochemical windows and glass transition temperatures in addition to a cold crystallization and a melt temperature for ME-FIL7. Therefore, the cationic structure and counter anion affect the physicochemical properties of these ME-FILs together.

Investigation on Water Vapor Adsorption of Silica-Phosphonium Ionic Liquids Hybrid Material

Adsorption and diffusion of water vapor in phosphonium ionic liquid modified silica gel were studied, aiming to reduce the loading of water vapor in porous materials. The modified silica gel was prepared through a grafting method and characterized by FTIR, thermal gravity analysis and X-ray photoelectron spectroscopy. N2 sorption isotherms at -196 °C and CO2 sorption isotherms at 0 °C were also measured to analyzee the porosity. Water vapor adsorption equilibriums at 25 °C up to 30 mbar were tested. The results indicate that the ionic liquids (ILs) phase acts as a protecting film which decreases water vapor adsorption. The improvement of water-resistant performance is also attributed to the decrease of micro-porosity and silanol groups on the silica surface. Diffusion behavior of water vapor on modified silica was determined on the basis of the adsorption equilibrium. The effective diffusivity of water vapor in modified silica is almost the same as in bare silica and decreases with the increasing of water vapor loading.