Preparation and Characterization of Polyethersulfone/Activated Carbon Composite Membranes for Water Filtration

Ultrafiltration membrane technology holds promise for wastewater treatment, but its widespread application is hindered by fouling and flux reduction issues. One effective strategy for enhancing ultrafiltration membranes involves incorporating activated carbon powder. In this study, composite polyethersulfone (PES) ultrafiltration membranes were fabricated to include activated carbon powder concentrations between 0 and 1.5 wt.%, with carbon size fixed at 200 mesh. The ultrafiltration membranes were evaluated in terms of membrane morphology, hydrophilicity, pure water flux, equilibrium water content, porosity, average pore size, protein separation, and E-coli bacteria removal. It was found that the addition of activated carbon to PES membranes resulted in improvements in some key properties. By incorporating activated carbon powder, the hydrophilicity of PES membranes was enhanced, lowering the contact angle from 60° to 47.3° for composite membranes (1.0 wt.% of activated carbon) compared to the pristine PES membrane. Water flux tests showed that the 1.0 wt.% composite membrane yielded the highest flux, with an improvement of nearly double the initial value at 2 bar, without compromising bovine serum albumin rejection or bacterial removal capabilities. This study also found that the inclusion of activated carbon had a minor impact on the membrane's porosity and equilibrium water content. Overall, these insights will be beneficial in determining the optimal concentration of activated carbon powder for PES ultrafiltration membranes.

Next-generation ultrafiltration membranes: A review of material design, properties, recent progress, and challenges

Membrane technology utilizing ultrafiltration (UF) processes has emerged as the most widely used and cost-effective simple process in many industrial applications. The industries like textiles and petroleum refining are promptly required membrane based UF processes to alleviate the potential environmental threat caused by the generation of various wastewater. At the same time, major limitations such as material selection as well as fouling behavior challenge the overall performance of UF membranes, particularly in wastewater treatment. Therefore, a complete discussion on material design with structural property relation and separation performance of UF membranes is always exciting. This state-of-the-art review has exclusively focused on the development of UF membranes, the material design, properties, progress in separation processes, and critical challenges. So far, most of the review articles have examined the UF membrane processes through a selected track of paving typical materials and their limited applications. In contrast, in this review, we have exclusively aimed at comprehensive research from material selection and fabrication methods to all the possible applications of UF membranes, giving more attention and theoretical understanding to the complete development of high-performance UF systems. We have discussed the methodical engineering behind the development of UF membranes regardless of their materials and fabrication mechanisms. Identifying the utility of UF membrane systems in various applications, as well as their mode of separation processes, has been well discussed. Overall, the current review conveys the knowledge of the present-day significance of UF membranes together with their future prospective opportunities whilst overcoming known difficulties in many potential applications.

Effect of Polyvinylpyrrolidone on Polyvinylidene Fluoride/Hydroxyapatite- Blended Nanofiltration Membranes: Characterization and Filtration Properties

INTRODUCTION

The application of polyvinylidene fluoride (PVDF) as a filtration membrane is limited due to its hydrophobicity. This paper elaborated on the fabrication process of nanofiltration PVDF membrane incorporating various quantities of hydrophilic polyvinylpyrrolidone (PVP) and hydroxyapatite (HA) using a wet phase inversion method to improve its hydrophilicity.

METHODS

The membrane was fabricated by using the wet phase inversion method. It was then characterized in terms of water permeability, water contact angle, water content, surface energy, and surface porosity. Bacteria and Fe ions filtration was conducted to investigate the membrane filtration performance.

RESULTS

The PVDF/PVP/HA-blended membrane showed the highest water permeability (6,165 LMH/Bar), water content (45.2 %), and surface energy (104.1 mN/m) when 2 wt.% of PVP was introduced into the base polymer PVDF. This fabricated membrane, labeled as PVP 2.0, also showed the lowest contact angle (64°) and the highest surface porosity (42%).

CONCLUSION

Overall, the PVP introduction patents into the polymeric membrane doping solution potentially improves membrane hydrophilicity and permeability.

Antibacterial Activity of Silver Nanoflake (SNF)-Blended Polysulfone Ultrafiltration Membrane

The aim of this research was to study the possibility of using silver nanoflakes (SNFs) as an antibacterial agent in polysulfone (PSF) membranes. SNFs at different concentrations (0.1, 0.2, 0.3 and 0.4 wt.%) were added to a PSF membrane dope solution. To investigate the effect of SNFs on membrane performance and properties, the water contact angle, protein separation, average pore size and molecular weight cutoffs were measured, and water flux and antibacterial tests were conducted. The antimicrobial activities of the SNFs were investigated using Escherichia coli taken from river water. The results showed that PSF membranes blended with 0.1 wt.% SNFs have contact angles of 55°, which is less than that of the pristine PSF membrane (81°), exhibiting the highest pure water flux. Molecular weight cutoff values of the blended membranes indicated that the presence of SNFs does not lead to enlargement of the membrane pore size. The rejection of protein (egg albumin) was improved with the addition of 0.1 wt.% SNFs. The SNFs showed antimicrobial activity against Escherichia coli, where the killing rate was dependent on the SNF concentration in the membranes. The identified bacterial colonies that appeared on the membranes decreased with increasing SNF concentration. PSF membranes blended with SNF, to a great degree, possess quality performance across several indicators, showing great potential to be employed as water filtration membranes.

Enhanced water flux and bacterial resistance in cellulose acetate membranes with quaternary ammoniumpropylated polysilsesquioxane

An enhanced water flux and anti-fouling nanocomposite ultrafiltration membrane based on quaternary ammoniumpropylated polysilsesquioxane (QAPS)/cellulose acetate (QAPS@CA) was fabricated by in situ sol-gel processing via phase inversion followed by quaternization with methyl iodide (CH₃I). Membrane characterizations were performed based on the contact angle, FTIR, SEM, and TGA properties. Membrane separation performance was assessed in terms of pure water flux, rejection, and fouling resistance. The 7%QAPS@CA nanocomposite membrane showed an increased wettability (46.6° water contact angle), water uptake (113%) and a high pure water permeability of ∼370 L m^-2 h^-1 bar^-1. Furthermore, the 7%QAPS@CA nanocomposite membrane exhibited excellent bactericidal properties (∼97.5% growth inhibition) against Escherichia coli (E. coli) compared to the bare CA membrane (0% growth inhibition). The 7%QAPS@CA nanocomposite membrane can be recommended for water treatment and biomedical applications.

Study Effect of nAg Particle Size on the Properties and Antibacterial Characteristics of Polysulfone Membranes

Polysulfone ultrafiltration membranes were fabricated using various sizes (20, 40, and 90-210 nm) of silver nanoparticles (nAg) blended in a dope solution. To characterize the performance and properties of the prepared membranes, scanning electron microscopy (SEM), water contact angle, protein separation, water flux, and antibacterial tests were conducted. The characterization results revealed that when nAg particles (20 nm) were blended into the base polymer PSF, the PSF/nAg blended membrane had the lowest contact angle (58.5°) and surface energy (110.7 mN/m). When experimenting with ultrafiltration using protein solutions, bare PSF and PSF/nAg-20 blended membranes gave similar values of protein rejection: 93% of bovine serum albumin (BSA) and 70% of lysozyme rejection. Furthermore, SEM studies showed that the surface pore size was reduced by adding 20 nm nAg particles in the casting solution. Most importantly, the introduction of 40 nm nAg particles reduced the growth of bacterial colonies on the membrane surface by up to 72%. These findings revealed that nAg particles are expected to be a potential modifier for the fabrication of an ultrafiltration membrane.

Efficacy of MOF-199 in improvement of permeation, morphological, antifouling and antibacterial characteristics of polyvinylidene fluoride membranes

Metal–organic frameworks (MOFs) are widely explored for advances in hybrid membranes because of their bonding and fondness in polymers.

Enhanced permeability, mechanical and antibacterial properties of cellulose acetate ultrafiltration membranes incorporated with lignocellulose nanofibrils

Cellulose acetate (CA) ultrafiltration membranes are attracting more attention in wastewater purification due to its biodegradability and eco-friendly. The application of CA membranes, however, is limited by high susceptibility to bacterial corrosion and lack of mechanical tolerance that results in loss of life. To solve the above problems, we first fabricated the CA-based composite membranes incorporated with bamboo-based lignocellulose nanofibrils (LCNFs) by a strategy of phase inversion. LCNFs was prepared by using a combined method of one-step chemical pretreatment and acid hydrolysis coupled with high-pressure homogenization. The as-prepared CA/LCNFs composite membranes with 4 wt% lignin in the LCNFs exhibited high tensile strength of 7.08 MPa and strain-at-break of 12.21%, and high filtration permeability of 188.23 L·m^-2·h^-1 as ultrafiltration membranes for wastewater treatment, which could obviously inhibit the growth of Escherichia coli.

Preparation of an Asymmetric Membrane from Sugarcane Bagasse Using DMSO as Green Solvent

Asymmetric cellulose acetate membranes have been successfully fabricated by phase inversion, using sugarcane bagasse (SB) as the starting material. SB is a raw material with high potential to produce cellulose derivatives due to its structure and morphology. Cellulose was extracted from SB by pretreatment with solutions of 5 wt% NaOH, 0.5 wt% EDTA; then bleached with 2 wt% H2O2. Cellulose acetate (CA) was prepared by the reaction between extracted cellulose with acetic anhydride, and H2SO4 as a catalyst. The obtained CA exhibited a high degree of substitution (2.81), determined with 1H-NMR spectroscopy and titration. The functional groups and thermal analysis of the extracted cellulose and the synthesized CA have been investigated by Fourier transform infrared spectroscopy (FT-IR), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The change in the crystallinity of the extracted cellulose and CA was evaluated by X-ray diffraction (XRD) spectroscopy. Asymmetric membranes were fabricated using dimethyl sulfoxide (DMSO) as the solvent, with a casting thickness of 250 µm. The obtained membranes were studied by scanning electron microscopy (SEM), DSC and atomic force microscopy (AFM). The hydrophilicity of the membranes was evaluated, as demonstrated by the measurement of water contact angle (WCA) and water content. Furthermore, the antifouling properties of membranes were also investigated.