The UCST phase transition of a dextran based copolymer in aqueous media with tunable thermoresponsive behavior

A hydrogen bonded UCST polymer has been developed by grafting of methacrylamide and acrylic acid on dextran via free radical polymerization.

Synthesis and Characterization of Temperature-Responsive N-Cyanomethylacrylamide-Containing Diblock Copolymer Assemblies in Water

We have previously demonstrated that poly(N-cyanomethylacrylamide) (PCMAm) exhibits a typical upper-critical solution temperature (UCST)-type transition, as long as the molar mass of the polymer is limited, which was made possible through the use of reversible addition-fragmentation chain transfer (RAFT) radical polymerization. In this research article, we use for the first time N-cyanomethylacrylamide (CMAm) in a typical aqueous dispersion polymerization conducted in the presence of poly(N,N-dimethylacrylamide) (PDMAm) macroRAFT agents. After assessing that well-defined PDMAm-b-PCMAm diblock copolymers were formed through this aqueous synthesis pathway, we characterized in depth the colloidal stability, morphology and temperature-responsiveness of the dispersions, notably using cryo-transmission electron microscopy (cryo-TEM), dynamic light scattering (DLS), small angle X-ray scattering (SAXS) and turbidimetry. The combined analyses revealed that stable nanometric spheres, worms and vesicles could be prepared when the PDMAm block was sufficiently long. Concerning the thermoresponsiveness, only diblocks with a PCMAm block of a low degree of polymerization (DPn,PCMAm < 100) exhibited a UCST-type dissolution upon heating at low concentration. In contrast, for higher DPn,PCMAm, the diblock copolymer nano-objects did not disassemble. At sufficiently high temperatures, they rather exhibited a temperature-induced secondary aggregation of primary particles. In summary, we demonstrated that various morphologies of nano-objects could be obtained via a typical polymerization-induced self-assembly (PISA) process using PCMAm as the hydrophobic block. We believe that the development of this aqueous synthesis pathway of novel PCMAm-based thermoresponsive polymers will pave the way towards various applications, notably as thermoresponsive coatings and in the biomedical field.

Multifunctional polymeric micellar nanomedicine in the diagnosis and treatment of cancer

Polymeric micelles are a prevalent topic of research for the past decade, especially concerning their fitting ability to deliver drug and diagnostic agents. This delivery system offers outstanding advantages, such as biocompatibility, high loading efficiency, water-solubility, and good stability in biological fluids, to name a few. The multifunctional polymeric micellar architect offers the added capability to adapt its surface to meet the looked-for clinical needs. This review cross-talks the recent reports, proof-of-concept studies, patents, and clinical trials that utilize polymeric micellar family architectures concerning cancer targeted delivery of anticancer drugs, gene therapeutics, and diagnostic agents. The manuscript also expounds on the underlying opportunities, allied challenges, and ways to resolve their bench-to-bedside translation for allied clinical applications.

Near-infrared light-responsive UCST-nanogels using an efficient nickel-bis(dithiolene) photothermal crosslinker

A new kind of near-infrared (NIR) light-responsive polymer nanogel is demonstrated.

Thermoresponsive properties of poly(acrylamide-co-acrylonitrile)-based diblock copolymers synthesized (by PISA) in water

UCST-type poly(acrylamide-co-acrylonitrile) diblock copolymers synthesized in water (by PISA) can not only undergo reversible temperature-induced chain dissociation, but also temperature-induced morphological transition.

Multiple-Responsive and Amphibious Hydrogel Actuator Based on Asymmetric UCST-Type Volume Phase Transition

Thermoresponsive hydrogel actuators have attracted tremendous interest due to their promising applications in artificial muscles, soft robotics, and flexible electronics. However, most of these materials are based on polymers with lower critical solution temperature (LCST), while those from upper critical solution temperature (UCST) are rare. Herein, we report a multiple-responsive UCST hydrogel actuator based on the complex of poly(acrylic acid) (PAAc) and poly(acrylamide) (PAAm). By applying a heterogeneous photopolymerization, a bilayer hydrogel was obtained, including a layer of the interpenetrating network (IPN) of PAAm/PAAc and a layer of a single network of PAAm. When cooled down below the UCST, the PAAm/PAAc layer contracted due to the hydrogen bonding of the two polymers while the PAAm layer stays in swelling state, driving the hydrogel to curl. By adjusting the composition of the two layers, the amplitude of actuation behavior could be regulated. By creating patterned IPN domains with photomasks, the hydrogel could deform into complex two-dimensional (2D) and three-dimensional (3D) shapes. An active motion was realized in both water and oil bath, thanks to the internal water exchange between the two layers. Interestingly, the hydrogel actuator is also responsive to urea and salts (Na₂SO₄, NaCl, NaSCN), due to that the strength of the hydrogen bonds in the IPN changes with the additives. Overall, the current study realized an anisotropic UCST transition by introducing asymmetrically distributed polymer-polymer hydrogen bonds, which would inspire new inventions of intelligent materials.

Biodegradable zwitterionic nanoparticles with tunable UCST-type phase separation under physiological conditions

Thermo-responsive polymeric nanoparticles (NPs) are emerging as a powerful tool in nanomedicine for the fabrication of advanced drug delivery systems. In addition to their size and biodegradation rate, phase separation of NPs upon application of a thermal stimulus provides an additional switch to control the rate of release of active components. Among the materials currently developed for biomedical applications, NPs stabilized by zwitterionic polymers are gaining increasing interest due to their high stability and ability to escape the body immune response. Yet, biodegradable zwitterionic NPs with temperature response under physiological conditions are currently not available. Here, we develop a new class of biodegradable zwitterionic NPs that exhibit UCST phase transition in the biological temperature range (T = 30-45 °C) and in physiological solution (i.e. 0.9% w/w NaCl). We design a strategy that relies on the self-assembly of block copolymers produced via reversible addition-fragmentation chain transfer (RAFT) emulsion polymerization. These copolymers comprise a zwitterionic portion exhibiting an upper critical solution temperature (UCST) and a biodegradable hydrophobic block consisting of oligoesters functionalized with a vinyl group. This modular macromolecular architecture allows us to independently control a variety of NP properties by modifying the individual components of the copolymer. In particular, the zwitterionic block of the copolymers controls the UCST-type phase separation behavior, while the number of the oligoester repeating units governs the size of the NPs and the length of the oligoester dictates the degradation rate. After demonstrating the synthesis of highly controlled degradable NPs, we show the potential of this new class of materials in the context of drug delivery by controlling the release of a drug-mimic molecule upon temperature variations in a broad time range from few minutes to 20 hours.