Synthesis of phosphine oxide based amphiphilic molecules via ring-opening Wittig olefination of a macrocyclic phosphoranylidene and their property study as non-ionic surfactants

Glucoconjugated Dinuclear Copper(II) Complex: An Efficient Catalyst for Stereoselective Synthesis of Trisubstituted Propargylamines via Solvent-free A3 Coupling Reaction

Development of catalytic systems using nontoxic natural precursors is the need of the era, and along this line, we have synthesized a new D-glucose derived ligand (4,6-O-ethylidene-N-(2-hydroxy-4-(octyloxy)benzylidene)-β-D-glucopyranosylamine) and its dinuclear copper(II) complex. The molecular structure of the complex has been established by single-crystal X-ray diffraction studies and detailed noncovalent intermolecular interactions present in it have been explored by Hirshfeld surface analysis. Further, the complex has been used as a catalyst in the enantioselective (87-99 % ee) synthesis of propargylamines in good to excellent yield (82-95 %) via aldehyde-amines-alkynes (A3) coupling reaction under solvent-free condition. The formation of aminal intermediate during the reaction has been confirmed by 1H-NMR and single-crystal X-ray diffraction studies. The catalytic system is reusable without any appreciable loss in the enantioselectivity or product yield.

Synthesis of Aryldiphenylphosphine Oxides by Quaternization of Tertiary Diphenylphosphines with Aryl Bromides Followed by the Wittig Reaction

A two-step method for the synthesis of aryldiphenylphosphine oxides from tertiary diphenylphosphines and aryl bromides is developed. The first step is the quaternization of methyldiphenylphosphine or benzyldiphenylphosphine with aryl bromides. This quaternization can be nickel-catalyzed (metal-free in some cases), and tolerate of a variety of functional groups, furnishing quaternary phosphonium salts in 48-90% yields. The second step is Wittig reactions of these quaternary phosphonium salts with furan-2-carbaldehyde or p-chlorobenzaldehyde to provide aryldiphenylphosphine oxides in 27-90% yields. The use of the Wittig reaction for the synthesis of tertiary phosphine oxides is in contrast to its traditional use for the synthesis of olefins, leaving tertiary phosphine oxide as a byproduct. This quaternization-Wittig method can be applied to synthesize aryldiphenylphosphine oxides that are difficult to access by the alkaline hydrolysis of aryltriphenylphosphonium salts, especially those bearing an electron-deficient aryl group. The ligand-coupling mechanism for the alkaline hydrolysis of (p-acylphenyl)triphenylphosphonim salts is also discussed.

Influence factors on the critical micelle concentration determination using pyrene as a probe and a simple method of preparing samples

The critical micelle concentration (CMC) is an important parameter of widely used surfactants and needs to be measured in the application and development of surfactants. Fluorometric method is a widely used method determining CMC values owing to the advantages of highly sensitivity, fast response and wide application range. There are two common methods (I and II) of preparing samples for CMC fluorometric determination. In the process of developing CMC probes with aggregation-induced emission (AIE) characteristics, we found that methods I and II were not suitable for CMC probes with AIE charateristics and developed a new sample preparation method (III), which is not only suitable for CMC probes with AIE characteristic but also decreases operation procedures and errors owing to omitting the addition of micro amount of dyes into each sample. To ascertain if method III is also suitable for other CMC probes without AIE characteristics, the CMC values of surfactants were determined by fluorometric method using widely used pyrene without AIE charateristic as probe and methods I-III to prepare samples. The obtained experimental results proved that method III not only was suitable for preparation of samples for CMC determination of surfactants using pyrene as probe but also led to the least average deviation (methods I-III led to ±0.13, ±0.34 and ±0.05 mM deviation for the CMC determination of sodium dodecyl sulfate (SDS), respectively). The CMC determination using pyrene as probe is based on its change in the ratio (I FIII/I FI) of its emission peaks I and III with surfactant concentration. Unexpectedly, it was found that the I FIII/I FI value of pyrene in surfactant solutions is sensitive to the measurement conditions changing exciting light energy, such as slit widths and sample-measured number. In addition, it was found that surfactant SDS or cetrimonium bromide from different suppliers not only has significantly different CMC values but also leads to very different I FIII/I FI values of pyrene in a certain concentration of surfactant, which can be used as a simple method to distinguish the same surfactant with different CMC values.