Size-dependent synthesis and catalytic activities of trimetallic PdAgCu mesoporous nanospheres in ethanol electrooxidation

Bioinspired Core-shell nanospheres integrated in multi-signal immunochromatographic sensor for high throughput sensitive detection of Bongkrekic acid in food

Nowadays, notable progress has been achieved in detecting foodborne toxins by employing nanoenzyme-based lateral flow immunoassay (NLFIA) sensors in point-of-care testing (POCT). It continues to be a major challenge to maximize the enzyme-like performance of nanozymes for educe any potential uncertainties in catalytic process. In this study, we employed a facile and efficient self-assembly approach to fabricate nucleoid-shell structured biomimetic nanospheres CuS@Au-Pt (CAP), which demonstrates enhanced brightness of the colorimetric signal, excellent affinity, and excellent peroxidase activity. The integration of CAP with a competitive-assay NLFIA platform enabled sensitive immunochromatographic detection of bongkrekic acid (BA), with LOD as low as 0.66 ng/mL. After signal amplification through enzyme-like reaction, the detection range was extended around 1-fold. Additionally, CAP-NLFIA effectively detected BA with a recovery rate of 80.96-119.36% for real samples. The study proposes using CAP as a signal reporter in a dual-readout LFIA, which can establish a high throughput sensitive detection platform.

Stabilizing Hydrogen Radicals in Two-Dimensional Cobalt-Copper Mesoporous Nanoplates for Complete Nitrate Reduction Electrocatalysis to Ammonia

Ambient electrochemical reduction of waste nitrate (NO3 -) represents an alternative green route for sustainable ammonia (NH3) electrosynthesis in water. Despites some encouraged achievements, sluggish eight electron and nine proton reduction routes that involve multi-step hydrogenation pathways have severely hindered their NH3 Faradaic efficiency (FENH3) and yield rate. Herein, we develop a robust two-dimensional mesoporous cobalt-copper (meso-CoCu) nanoplate electrocatalyst that delivers excellent performance of complete NO3 - reduction reaction (NO3RR), including superior FENH3 of 98.8 %, high NH3 yield rate of 3.39 mol h-1 g-1 and energy efficiency of 49.8 %, and good cycling stability. Mechanism investigations unveil that active hydrogen (*H) radicals produced from water splitting on Co sites spillover to adjacent Cu sites and further stabilize within confined mesopores, which kinetically promote its coupling hydrogenation reactions of nitrogen intermediates and thus facilitate complete NO3RR for favorable NH3 electrosynthesis. Moreover, meso-CoCu nanoplates perform well as a bifunctional electrocatalyst in the two-electrode coupling system that concurrently synthesizes NH3 from NO3 - at cathode and 2,5-furanedicarboxylic acid from 5-hydroxymethylfurfural at anode. This work in stabilizing *H radicals in mesoporous microenvironment provides some insights applied to various hydrogenation reactions for selective electrosynthesis of high value-added chemicals in water.

2D PtRhPb Mesoporous Nanosheets with Surface-Clean Active Sites for Complete Ethanol Oxidation Electrocatalysis

The development of active and selective metal electrocatalysts for complete ethanol oxidation reaction (EOR) into desired C1 products is extremely promising for practical application of direct ethanol fuel cells. Despite some encouraging achievements, their activity and selectivity remain unsatisfactory. In this work, it is reported that 2D PtRhPb mesoporous nanosheets (MNSs) with anisotropic structure and surface-clean metal site perform perfectly for complete EOR electrocatalysis in both three-electrode and two-electrode systems. Different to the traditional routes, a selective etching strategy is developed to produce surface-clean mesopores while retaining parent anisotropy quasi-single-crystalline structure without the mesopore-forming surfactants. This method also allows the general synthesis of surface-clean mesoporous metals with other compositions and structures. When being performed for alkaline EOR electrocatalysis, the best PtRhPb MNSs deliver remarkably high activity (7.8 A mg-1) and superior C1 product selectivity (70% of Faradaic efficiency), both of which are much better than reported electrocatalysts. High performance is assigned to multiple structural and compositional synergies that not only stabilized key OHads intermediate by surface-clean mesopores but also separated the chemisorption of two carbons in ethanol by adjacent Pt and Rh sites, which facilitate the oxidation cleavage of stable C─C bond for complete EOR electrocatalysis.

Enzymatic Mesoporous Metal Nanocavities for Concurrent Electrocatalysis of Nitrate to Ammonia Coupled with Polyethylene Terephthalate Upcycling

Electrochemical upcycling of waste pollutants into high value-added fuels and/or chemicals is recognized as a green and sustainable solution that can address the resource utilization on earth. Despite great efforts, their progress has seriously been hindered by the lack of high-performance electrocatalysts. In this work, bimetallic PdCu mesoporous nanocavities (MCs) are reported as a new bifunctional enzymatic electrocatalyst that realizes concurrent electrocatalytic upcycling of nitrate wastewater and polyethylene terephthalate (PET) plastic waste. Abundant metal mesopores and open nanocavities of PdCu MCs provide the enzymatic confinement of key intermediates for the deeper electroreduction of nitrate and accelerate the transport of reactants/products within/out of electrocatalyst, thus affording high ammonia Faradic efficiency (FENH3) of 96.6% and yield rate of 5.6 mg h-1 mg-1 at the cathode. Meanwhile, PdCu MC nanozymes trigger the selective electrooxidation of PET-derived ethylene glycol (EG) into glycolic acid (GA) and formic acid with high FEs of >90% by a facile regulation of potentials at the anode. Moreover, concurrent electrosynthesis of value-added NH3 and GA is disclosed in the two-electrode coupling system, further confirming the high efficiency of bifunctional PdCu MC nanozymes in producing value-added fuels and chemicals from waste pollutants in a sustainable manner.

Two-dimensional mesoporous metals: a new era for designing functional electrocatalysts

Two-dimensional (2D) mesoporous metals contribute a unique class of electrocatalyst materials for electrochemical applications. The penetrated mesopores of 2D mesoporous metals expose abundant accessible undercoordinated metal sites, while their 2D nanostructures accelerate the transport of electrons and reactants. Therefore, 2D mesoporous metals have exhibited add-in structural functions with great potential in electrocatalysis that not only enhance electrocatalytic activity and stability but also optimize electrocatalytic selectivity. In this Perspective, we summarize recent progress in the design, synthesis, and electrocatalytic performance of 2D mesoporous metals. Four main strategies for synthesizing 2D mesoporous metals, named the CO (and CO container) induced route, halide ion-oriented route, interfacial growth route, and metal oxide atomic reconstruction route, are presented in detail. Moreover, electrocatalytic applications in several important reactions are summarized to highlight the add-in structural functions of 2D mesoporous metals in enhancing electrochemical activity, stability, and selectivity. Finally, current challenges and future directions are discussed in this area. This Perspective offers some important insights into both fundamental investigations and practical applications of novel high-performance functional electrocatalysts.

In situ electrochemical synthesis of Pd aerogels as highly efficient anodic electrocatalysts for alkaline fuel cells

Improving the utilization of noble metals is extremely urgent for fuel cell electrocatalysis, while three-dimensional hierarchical noble metal aerogels with abundant sites and channels are proposed to reinforce their electrocatalytic performances and decrease their amounts. Herein, novel Pd aerogels with tunable surface chemical states were prepared through a facile in situ electrochemical activation, starting with PdO x aerogels by the hydrolysis method. The hierarchical porous Pd aerogels showed unprecedented high activity towards the electrocatalytic oxidation of fuels including methanol (2.99 A mgPd -1), ethanol (8.81 A mgPd -1), and others in alkali, outperforming commercial catalysts (7.12- and 13.66-fold, corresponding to methanol and ethanol). Theoretical investigation unveiled the hybrid surface states with metallic and oxidized Pd species in Pd aerogels to regulate the adsorption of intermediates and facilitate the synergistic oxidation of adsorbed *CO, resulting in enhanced activity with the MOR as the model. Therefore, efficient Pd aerogels through the in situ electrochemical activation of PdO x aerogels were proposed and showed great potential for fuel cell anodic electrocatalysis.

Hierarchical Design in Nanoporous Metals

Hierarchically porous metals possess intriguing high accessibility of matter molecules and unique continuous metallic frameworks, as well as a high level of exposed active atoms. High rates of diffusion and fast energy transfer have been important and challenging goals of hierarchical design and porosity control with nanostructured metals. This review aims to summarize recent important progress toward the development of hierarchically porous metals, with special emphasis on synthetic strategies, hierarchical design in structure-function and corresponding applications. The current challenges and future prospects in this field are also discussed.

Noble-Metal-Based Hollow Mesoporous Nanoparticles: Synthesis Strategies and Applications

As second-generation mesoporous materials, mesoporous noble metals (NMs) are of significant interest for their wide applications in catalysis, sensing, bioimaging, and biotherapy owing to their structural and metallic features. The introduction of interior hollow cavity into NM-based mesoporous nanoparticles (MNs), which subtly integrate hierarchical hollow and mesoporous structure into one nanoparticle, produces a new type of hollow MNs (HMNs). Benefiting from their higher active surface, better electron/mass transfer, optimum electronic structure, and nanoconfinement space, NM-based HMNs exhibit their high efficiency in enhancing catalytic activity and stability and tuning catalytic selectivity. In this review, recent progress in the design, synthesis, and catalytic applications of NM-based HMNs is summarized, including the findings of the groups. Five main strategies for synthesizing NM-based HMNs, namely silica-assisted surfactant-templated nucleation, surfactant-templated sequential nucleation, soft "dual"-template, Kirkendall effect in synergistic template, and galvanic-replacement-assisted surfactant template, are described in detail. In addition, the applications in ethanol oxidation electrocatalysis and hydrogenation reactions are discussed to highlight the high activity, enhanced stability, and optimal selectivity of NM-based HMNs in (electro)catalysis. Finally, the further outlook that may lead the directions of synthesis and applications of NM-based HMNs is prospected.

Highly Curved, Quasi-Single-Crystalline Mesoporous Metal Nanoplates Promote CC Bond Cleavage in Ethanol Oxidation Electrocatalysis

The ability to manipulate metal nanocrystals with well-defined morphologies and structures is greatly important in material chemistry, catalysis chemistry, nanoscience, and nanotechnology. Although 2D metals serve as interesting platforms, further manipulating them in solution with highly penetrated mesopores and ideal crystallinity remains a huge challenge. Here, an easy yet powerful synthesis strategy for manipulating the mesoporous structure and crystallinity of 2D metals in a controlled manner with cetyltrimethylammonium chloride as the mesopore-forming surfactant and extra iodine-ion as the structure/facet-selective agent is reported. This strategy allows for preparing an unprecedented type of 2D quasi-single-crystalline mesoporous nanoplates (SMPs) with highly curved morphology and controlled metal composition. The products, for example, PdCu SMPs, feature abundant undercoordinated sites, optimized electronic structures, excellent electron/mass transfers, and confined mesopore environments. Curved PdCu SMPs exhibit remarkable electrocatalytic activity of 6.09 A mg_Pd ^-1 and stability for ethanol oxidation reaction (EOR) compared with its counterpart catalysts and commercial Pd/C. More importantly, PdCu SMPs are highly selective for EOR electrocatalysis that dramatically promotes C-C bond cleavage with a superior C1 pathway selectivity as high as 72.1%.

Synthesizing ordered mesoporous Ni spheres with uniform and adjustable size through a one-step Pd2+-assisted soft-templating strategy

Developing an effective way to synthesize uniform ordered mesoporous metal spheres with controllable diameter is important for enhancing their performance in various applications but remains a challenge. Herein, a one-step and facile Pd²⁺-assisted soft-templating strategy is reported to synthesize ordered mesoporous Ni spheres (OMNiS) with highly uniform and tunable diameters. In this synthesis methodology, lyotropic liquid crystals (LLCs) are used as a meso-structural template and Pd nuclei obtained from the reduction of Pd²⁺ ions are used as nucleation sites for directing Ni deposition. The OMNiS samples with average sphere diameter ranging from 50 nm to 190 nm are produced by varying the amount of Pd²⁺ in the LLC precursor, revealing that the Pd nuclei play a key role in improving the uniformity of the mesoporous Ni spheres and adjusting the sphere diameter. The satisfactory combination of uniform sphere size, high surface area, great conductivity, and highly ordered mesoporous structure for the optimal OMNiS-100 sample contributes to its superior electrocatalytic activity for the oxygen evolution reaction (OER) in an alkaline electrolyte with a low overpotential of 271 mV to drive a current density of 10 mA cm^-2, which is much smaller than that of RuO₂ (368 mV), along with a remarkable durability.

Synthesis of Pd3 Sn and PdCuSn Nanorods with L12 Phase for Highly Efficient Electrocatalytic Ethanol Oxidation

The crystal phase of nanomaterials is one of the key parameters determining their physicochemical properties and performance in various applications. However, it still remains a great challenge to synthesize nanomaterials with different crystal phases while maintaining the same composition, size, and morphology. Here, a facile, one-pot, wet-chemical method is reported to synthesize Pd₃ Sn nanorods with comparable size and morphology but different crystal phases, that is, an ordered intermetallic and a disordered alloy with L1₂ and face-centered cubic (fcc) phases, respectively. The crystal phase of the as-synthesized Pd₃ Sn nanorods is easily tuned by altering the types of tin precursors and solvents. Moreover, the approach can also be used to synthesize ternary PdCuSn nanorods with the L1₂ crystal phase. When used as electrocatalysts, the L1₂ Pd₃ Sn nanorods exhibit superior electrocatalytic performance toward the ethanol oxidation reaction (EOR) compared to their fcc counterpart. Impressively, compared to the L1₂ Pd₃ Sn nanorods, the ternary L1₂ PdCuSn nanorods exhibit more enhanced electrocatalytic performance toward the EOR, yielding a high mass current density up to 6.22 A mg_Pd ^-1 , which is superior to the commercial Pd/C catalyst and among the best reported Pd-based EOR electrocatalysts.

Nanoscaled and Atomic Ruthenium Electrocatalysts Confined Inside Super-Hydrophilic Carbon Nanofibers for Efficient Hydrogen Evolution Reaction

A series of Ru-based catalysts have been developed for the hydrogen evolution reaction (HER) by the facile impregnation of copious and eco-friendly bacterial cellulose (BC) with Ru(bpy)₃ Cl₂ (bpy = 2,2'-bipyridine) followed by pyrolysis. After the oxidation and molecular recomposition processes that occur within the BC precursors during pyrolysis, sub-2 nm Ru nanoparticles (NPs) and atomic Ru species confined within surface-oxidized N-doped carbon nanofibers (CNFs) can be observed in the derived catalysts. The surface oxidation of CNFs leads the derived catalysts with super hydrophilicity and water-absorbing capacity, and also provides dimensional confinement for the nanoscaled and atomic Ru species. With these added structural advantages and the component synergy, the derived catalysts show superior HER activities, for which the overpotentials are as low as 19.6 mV (1 m KOH) and 55.0 mV (0.5 m H₂ SO₄ ) for the most active case at the current density of 10 mA cm^-2 . Moreover, superior HER activity can be also achieved for the catalysts derived with a wide range of Ru loadings. Finally, the influence of Ru NP size on HER activity is investigated by density functional theory simulations. This method provides a reliable protocol for preparing highly active HER catalysts for scale-up applications.

Synthesis and Characterization of PdAgNi/C Trimetallic Nanoparticles for Ethanol Electrooxidation

The direct use of ethanol in fuel cells presents unprecedented economic, technical, and environmental opportunities in energy conversion. However, complex challenges need to be resolved. For instance, ethanol oxidation reaction (EOR) requires breaking the rigid C–C bond and results in the generation of poisoning carbonaceous species. Therefore, new designs of the catalyst electrode are necessary. In this work, two trimetallic Pd_xAg_yNi_z/C samples are prepared using a facile borohydride reduction route. The catalysts are characterized by X-ray diffraction (XRD), Energy-Dispersive X-ray spectroscopy (EDX), X-ray photoelectron Spectroscopy (XPS), and Transmission Electron Microscopy (TEM) and evaluated for EOR through cyclic voltammetry (CV), chronoamperometry (CA), and electrochemical impedance spectroscopy (EIS). The XRD patterns have shown a weak alloying potential between Pd, and Ag prepared through co-reduction technique. The catalysts prepared have generally shown enhanced performance compared to previously reported ones, suggesting that the applied synthesis may be suitable for catalyst mass production. Moreover, the addition of Ag and Ni has improved the Pd physiochemical properties and electrocatalytic performance towards EOR in addition to reducing cell fabrication costs. In addition to containing less Pd, The PdAgNi/C is the higher performing of the two trimetallic samples presenting a 2.7 A/mg_Pd oxidation current peak. The Pd₄Ag₂Ni₁/C is higher performing in terms of its steady-state current density and electrochemical active surface area.

Highly efficient blackberry-like trimetallic PdAuCu nanoparticles with optimized Pd content for ethanol electrooxidation

The rational design of highly efficient catalysts for ethanol electrooxidation is extremely challenging for developing direct ethanol fuel cells (DEFCs). Herein, a facile one-pot method has been developed to prepare blackberry-like PdAuCu nanoparticles (NPs) with tunable composition and surface structures. Among PdAuCu NPs with different Pd contents (1.6-22 mass%), PdAuCu NPs-0.5 (contained Pd at 2.5 mass%) delivered one of the highest catalytic activities of Pd-based catalysts towards ethanol electrooxidation, exhibiting a mass activity of 23.0 A mg_Pd^-1. Kinetic analysis, electrochemical impedance spectroscopy and CO stripping test results suggested that the excellent electrocatalytic activity may originate from the optimized balance between Pd content and surface structure of PdAuCu NPs-0.5. The optimization of the balance between composition and surface structure would contribute to the further design of multimetallic nanoparticles for fuel cells and other applications.

Porous PdAg alloy nanostructures with a concave surface for efficient electrocatalytic methanol oxidation

Tuning the composition and surface structure of the metal nanocrystals offered viable avenues for enhancing catalytic performances. Herein, we report a facile one-pot strategy for the formation of PdAg porous alloy nanostructures (PANs) with a concave surface. Due to their highly open nanostructures and tunable d-band center features, PdAg PANs exhibit superior electrocatalytic activity and long-term durability than Pd nanoparticles (NPs) and Pd/C for methanol oxidation reaction (MOR) in alkaline media. Our results provide a feasible and efficient approach for the controlled synthesis of high-performance Pd-based nanomaterials for alkaline MOR.

Porous Noble Metal Electrocatalysts: Synthesis, Performance, and Development

Active sites (intrinsic activity, quantity, and distribution), electron transfer, and mass diffusion are three important factors affecting the performance of electrocatalysts. Composed of highly active components which are built into various network structures, porous noble metal is an inherently promising electrocatalysts. In recent years, great efforts have been made to explore new efficient synthesis methods and establish structural-performance relationships in the field of porous noble metal electrocatalysis. In this review, the very recent progress in strategies for preparing porous noble metal, including innovation and deeper understanding of traditional methods is summarized. A discussion of relationship between porous noble metal structure and electrocatalytic performance, such as accessibility of active sites, connectivity of skeleton structures, channels dimensions, and hierarchical structures, is provided.

Carbon-Supported Trimetallic Catalysts (PdAuNi/C) for Borohydride Oxidation Reaction

The synthesis of palladium-based trimetallic catalysts via a facile and scalable synthesis procedure was shown to yield highly promising materials for borohydride-based fuel cells, which are attractive for use in compact environments. This, thereby, provides a route to more environmentally friendly energy storage and generation systems. Carbon-supported trimetallic catalysts were herein prepared by three different routes: using a NaBH₄-ethylene glycol complex (PdAuNi/C_SBEG), a NaBH₄-2-propanol complex (PdAuNi/C_SBIPA), and a three-step route (PdAuNi/C_3-step). Notably, PdAuNi/C_SBIPA yielded highly dispersed trimetallic alloy particles, as determined by XRD, EDX, ICP-OES, XPS, and TEM. The activity of the catalysts for borohydride oxidation reaction was assessed by cyclic voltammetry and RDE-based procedures, with results referenced to a Pd/C catalyst. A number of exchanged electrons close to eight was obtained for PdAuNi/C_3-step and PdAuNi/C_SBIPA (7.4 and 7.1, respectively), while the others, PdAuNi/C_SBEG and Pd/C_SBIPA, presented lower values, 2.8 and 1.2, respectively. A direct borohydride-peroxide fuel cell employing PdAuNi/C_SBIPA catalyst in the anode attained a power density of 47.5 mW cm⁻² at room temperature, while the elevation of temperature to 75 °C led to an approximately four-fold increase in power density to 175 mW cm⁻². Trimetallic catalysts prepared via this synthesis route have significant potential for future development.

Cryoaerogels and Cryohydrogels as Efficient Electrocatalysts

Additive-free cryoaerogel coatings from noble metal nanoparticles are prepared and electrochemically investigated. By using liquid nitrogen or isopentane as cooling medium, two different superstructures are created for each type of noble metal nanoparticle. These materials (made from the same amount of particles) have superior morphological and catalytic properties as compared to simply immobilized, densely packed nanoparticles. The morphology of all materials is investigated with scanning electron microscopy (SEM). Electrochemically active surface areas (ECSAs) are calculated from cyclic voltammetry measurements. The catalytic activity is studied for the ethanol oxidation reaction (EOR). Both are found to be increased for superstructured materials prepared by cryoaerogelation. Furthermore, cryoaerogels with cellular to dendritic structure that arise from freezing with isopentane show the best catalytic performance and highest ECSA. Moreover, as a new class of materials, cryohydrogels are created for the first time by thawing flash-frozen nanoparticle solutions. Structure and morphology of these materials match with the corresponding types of cryoaerogels and are confirmed via SEM. Even the catalytic activity in EOR is in accordance with the results from cryoaerogel coatings. As a proof of concept, this approach offers a novel platform towards the easier and faster production of cryogelated materials for wet-chemical applications.

The use of amino-based functional molecules for the controllable synthesis of noble-metal nanocrystals: a minireview

Controlling the morphologies and structures of noble-metal nanocrystals has always been a frontier field in electrocatalysis. Functional molecules such as capping agents, surfactants and additives are indispensable in shape-control synthesis. Amino-based functional molecules have strong coordination abilities with metal ions, and they are widely used in the morphology control of nanocrystals. In this minireview, we pay close attention to recent advances in the use of amino-based functional molecules for the controllable synthesis of noble-metal nanocrystals. The effects of various amino-based molecules on differently shaped noble-metal nanocrystals, including zero-, one-, two-, and three-dimensional nanocrystals, are reviewed and summarized. The roles and mechanisms of amino-based small molecules and long-chain ammonium salts relating to the morphology-control synthesis of noble-metal nanocrystals are highlighted. Relationships between shape and electrocatalytic properties are also described. Finally, some key prospects and challenges relating to the controllable synthesis of noble-metal nanocrystals and their electrocatalytic applications are proposed.

Mesoporous Palladium-Boron-Sulfur Alloy Nanospheres for Efficient Hydrogen Evolution

Ternary noble metal-metalloid-nonmetal PdBS alloy mesoporous nanospheres (MSs) with three-dimensional central-radial pore channels were prepared for an electrocatalytic hydrogen evolution reaction. The synthesis was performed via precise control in the reduction and nucleation growth of ternary PdBS alloy MSs along confined cylinder mesophases assembled by amphiphilic dioctadecyldimethylammonium chloride. The resultant PdBS alloy MSs disclosed a remarkably improved electrocatalytic performance due to their structural and compositional synergies. This finding extended our knowledge on the rational design and targeted synthesis of novel noble metal-metalloid-nonmetal alloys with desired structures and morphologies for catalysis and other applications.

Plasmonic Alloys Reveal a Distinct Metabolic Phenotype of Early Gastric Cancer

Gastric cancer (GC) is a multifactorial process, accompanied by alterations in metabolic pathways. Non-invasive metabolic profiling facilitates GC diagnosis at early stage leading to an improved prognostic outcome. Herein, mesoporous PdPtAu alloys are designed to characterize the metabolic profiles in human blood. The elemental composition is optimized with heterogeneous surface plasmonic resonance, offering preferred charge transfer for photoinduced desorption/ionization and enhanced photothermal conversion for thermally driven desorption. The surface structure of PdPtAu is further tuned with controlled mesopores, accommodating metabolites only, rather than large interfering compounds. Consequently, the optimized PdPtAu alloy yields direct metabolic fingerprints by laser desorption/ionization mass spectrometry in seconds, consuming 500 nL of native plasma. A distinct metabolic phenotype is revealed for early GC by sparse learning, resulting in precise GC diagnosis with an area under the curve of 0.942. It is envisioned that the plasmonic alloy will open up a new era of minimally invasive blood analysis to improve the surveillance of cancer patients in the clinical setting.

Hierarchical defective palladium-silver alloy nanosheets for ethanol electrooxidation

Tuning the chemical composition and surface structure of electrodes is demonstrated as a feasible and effective strategy to tailor advanced catalysts for energy electrocatalysis. In this work, hierarchical palladium-silver alloy nanosheets (PdAg NS) with the thickness ~7 atoms and rich atomic defects are successfully prepared, using the carbon monoxide (CO) confinement approach. The optimized Pd₇Ag₃ NS/C exhibits 8.8 times higher catalytic peak current density and much better stability toward ethanol electrooxidation than Pd NS/C catalyst. The catalytic enhancement mechanism could be attributed to the synergetic effects among optimized electronic structure of Pd, novel architecture, and rich atomic defects.

A universal approach for the synthesis of mesoporous gold, palladium and platinum films for applications in electrocatalysis

High-surface-area mesoporous materials expose abundant functional sites for improved performance in applications such as gas storage/separation, catalysis, and sensing. Recently, soft templates composed of amphiphilic surfactants and block copolymers have been used to introduce mesoporosity in various materials, including metals, metal oxides and carbonaceous compounds. In particular, mesoporous metals are attractive in electrocatalysis because their porous networks expose numerous unsaturated atoms on high-index facets that are highly active in catalysis. In this protocol, we describe how to create mesoporous metal films composed of gold, palladium, or platinum using block copolymer micelle templates. The amphiphilic block copolymer micelles are the sacrificial templates and generate uniform structures with tunable pore sizes in electrodeposited metal films. The procedure describes the electrodeposition in detail, including parameters such as micelle diameters, deposition potentials, and deposition times to ensure reproducibility. The micelle diameters can be controlled by swelling the micelles with different solvent mixtures or by using block copolymer micelles with different molecular weights. The deposition potentials and deposition times allow further control of the mesoporous structure and its thickness, respectively. Procedures for example applications are included: glucose oxidation, ethanol oxidation and methanol oxidation reactions. The synthetic methods for preparation of mesoporous metal films will take ~4 h; the subsequent electrochemical tests will take ~5 h for glucose sensing and ~3 h for alcohol oxidation reaction.

Recent Advances in Noble Metal Catalysts for Hydrogen Production from Ammonia Borane

Interest in chemical hydrogen storage has increased, because the supply of fossil fuels are limited and the harmful effects of burning fossil fuels on the environment have become a focus of public concern. Hydrogen, as one of the energy carriers, is useful for the sustainable development. However, it is widely known that controlled storage and release of hydrogen are the biggest barriers in large-scale application of hydrogen energy. Ammonia borane (NH3BH3, AB) is deemed as one of the most promising hydrogen storage candidates on account of its high hydrogen to mass ratio and environmental benignity. Development of efficient catalysts to further improve the properties of chemical kinetics in the dehydrogenation of AB under appropriate conditions is of importance for the practical application of this system. In previous studies, a variety of noble metal catalysts and their supported metal catalysts (Pt, Pd, Au, Rh, etc.) have presented great properties in decomposing the chemical hydride to generate hydrogen, thus, promoting their application in dehydrogenation of AB is urgent. We analyzed the hydrolysis of AB from the mechanism of hydrogen release reaction to understand more deeply. Based on these characteristics, we aimed to summarize recent advances in the development of noble metal catalysts, which had excellent activity and stability for AB dehydrogenation, with prospect towards realization of efficient noble metal catalysts.

Nanoengineering 2D Dendritic PdAgPt Nanoalloys with Edge-Enriched Active Sites for Enhanced Alcohol Electroxidation and Electrocatalytic Hydrogen Evolution

Lots of research studies reveal that the surface atoms on the top/bottom facets of the nanosheets are the key features in enhancing electrocatalytic activity while the edge and corner sites of electrocatalysts often possess superior activity. Herein, we report 2D dendritic PdAgPt ternary nanoalloys with abundant crystal defects such as steps, twin boundary, and atomic holes, which can effectively work as catalytic active-sites. The morphology of PdAgPt nanoalloys can be regulated readily from dendritic nanosheets to nanowheels. Compared with binary Pd₆₈Ag₃₂ nanodendrites, Pd₆₂Pt₃₈ nanospheres, and Pt/C catalyst, the composition- and morphology-optimized Pd₄₃Ag₂₁Pt₃₆ nanowheels exhibit the best mass/specific activity and stability for methanol/ethanol oxidation reaction (MOR/EOR). The mass peak current density for EOR/MOR of Pd₄₃Ag₂₁Pt₃₆ is 7.08/3.50 times of the Pt/C catalyst. Simultaneously, the hydrogen evolution reaction performance of the Pd₄₃Ag₂₁Pt₃₆ nanowheels in terms of the lowest overpotential of 9 mv at a current density of 10 mA/cm² and high electrochemical stability is much better than that of binary Pd₆₈Ag₃₂ nanodendrites, Pd₆₂Pt₃₈ nanospheres, and Pt/C.

In Situ Seed-Mediated Growth of Polymer-Grafted Gold Nanoparticles

We report a facile yet general in situ seed-mediated method for the synthesis of polymer-grafted gold nanoparticles with narrow size distributions (<10%), accurately tunable sizes, and excellent colloidal stability. This method can be extended to a broad range of types and molecular weights of polymer ligands. Nanoparticles with different shapes can also be prepared by using preformed shaped nanoparticles directly as the seeds.

An aqueous synthesis of porous PtPd nanoparticles with reversed bimetallic structures for highly efficient hydrogen generation from ammonia borane hydrolysis

Fine construction of porous bimetallic nanomaterials with tunable components and structures is of great importance for their catalytic performance and durability. Herein, we present a facile and mild one-pot route for the preparation of porous PtPd bimetallic nanoparticles (NPs) with reversed structures in aqueous solution for the first time. To this end, a common ionic liquid (IL) 1-hexadecyl-3-methylimidazolium chloride ([C16mim]Cl) is utilized to direct the growth and assembly of porous structures of PtPd NPs. It is shown that the as-prepared porous Pt25Pd75 NPs have obvious hierarchical structures with nanoflowers as subunits and nanorods as basic units. The elemental components and structures of the porous PtPd NPs can be tuned by the precursor ratio and the [C16mim]Cl concentration. Furthermore, various porous PtPd bimetallic structures from Pd-on-Pt to Pt-on-Pd may be efficiently switched by controlling the concentration of glycine. Owing to their high specific surface area, porous hierarchical structures (including mesopores and micropores), and probable electronic effects between Pt and Pd, the porous Pt25Pd75 NPs (Pd-on-Pt structure) are found to exhibit prominent catalytic activity and high stability for hydrogen production from hydrolysis of ammonia borane.

Engineering bunched RhTe nanochains for efficient methanol oxidation electrocatalysis

We report a two-step method for the synthesis of bunched RhTe nanochains for excellent electro-oxidation of methanol.

Pore structure dependent activity and durability of mesoporous rhodium nanoparticles towards the methanol oxidation reaction

A significant porous structure effect of mesoporous rhodium nanoparticles on the electrocatalytic methanol oxidation reaction was reported.

Ultrathin PdFePb nanowires: One-pot aqueous synthesis and efficient electrocatalysis for polyhydric alcohol oxidation reaction

Synthesis of high-efficiency catalysts for alcohol oxidation reaction caused great interest in direct alcohol fuel cells (DAFCs). Ultrathin PdFePb nanowires (NWs) with an average diameter of 2.3 nm were synthesized by a simple and fast one-pot aqueous synthesis, using octylphenoxypolyethoxyethanol (NP-40) as the structure-directing agent. The as-prepared PdFePb NWs displayed an increscent electrochemically active surface area (ECSA, 121.18 m² g^-1 _Pd). For ethylene glycol oxidation reaction (EGOR) and glycerol oxidation reaction (GOR), PdFePb NWs exhibited much higher activity and superior stability, outperforming those of homemade PdFe NWs, PdPb NWs, commercial Pd black and Pd/C (20 wt%). These results reveal dramatically high catalytic activity and durability of ultrathin PdFePb NWs in enhancing polyols electrooxidation.

Ternary Palladium-Boron-Phosphorus Alloy Mesoporous Nanospheres for Highly Efficient Electrocatalysis

Alloying palladium (Pd) catalysts with various metalloid and nonmetal elements can improve their catalytic performance in different chemical reactions. However, current nanosynthesis methods can only generate Pd alloys containing one metalloid or nonmetal, which limits the types of element combinations that may be used to improve Pd-based nanocatalysts. Herein, we report a simple soft-templating synthetic strategy to co-alloy Pd with the metalloid boron (B) and the nonmetal phosphorus (P) to generate ternary PdBP mesoporous nanospheres (MSs) with three-dimensional dendritic frameworks. We use a one-step aqueous synthesis method where dimethylamine borane and sodium hypophosphite serve as the B and P sources, respectively, as well as the co-reducing agents to drive the nucleation and growth of ternary PdBP alloy on a sacrificial dioctadecyldimethylammonium chloride template. The concentration of metalloid to nonmetal and the diameters of dendritic MSs can be tailored. The synthetic protocol is also extended to other multicomponent PdMBP alloy MSs to generate different types of dendritic mesoporous frameworks. Boron and phosphorus are known to accelerate the kinetics of the electrochemical oxygen reduction reaction (ORR) and alcohol oxidation reactions (AORs), because their alloys promote the decomposition of oxygen-containing intermediates on Pd surfaces. The dendritic mesoporous morphology of the ternary PdBP MSs also accelerates electron/mass transfer and exposes numerous active sites, enabling better performance in the ORR and AORs. Extending the surfactant-templating synthetic route to multiple types of elements will enable the generation of libraries of multicomponent metal-metalloid-nonmetal alloy nanostructures with functions that are suitable for various targeted applications.

Insights into Compositional and Structural Effects of Bimetallic Hollow Mesoporous Nanospheres toward Ethanol Oxidation Electrocatalysis

A one-pot soft-templating method is reported to fabricate nanosized bimetallic PdAg hollow mesoporous nanospheres (HMSs) for electrocatalytic ethanol oxidation reaction (EOR). The synthesis relies on the "dual-template" surfactant of dioctadecyldimethylammonium chloride that drives in situ growth of mesoporous frameworks on the surface of vesicles into the HMSs with radially opened mesochannels. The synthetic protocol is extendable to engineer elemental compositions and hierarchical nanostructures of PdAg nanoalloys. This system thus provides a direct yet solid platform to understand catalytic add-in synergies of PdAg HMSs toward electrochemical EOR. By evaluating compositional and structural features separately, bimetallic Pd₆₅Ag₃₅ HMSs display the highest EOR activity with a mass activity of 4.61 A mg_Pd^-1. Mechanism studies indicate that synergistically electronic and bifunctional effects as well as structural advantages of Pd₆₅Ag₃₅ HMSs kinetically optimize the removal of poisoning carbonaceous intermediates and accelerate the diffusion processes (the rate-determining step), and thus promote the EOR performance accordingly.

Cyanogel auto-reduction induced synthesis of PdCo nanocubes on carbon nanobowls: a highly active electrocatalyst for ethanol electrooxidation

Direct ethanol fuel cells (DEFCs) with a high conversion efficiency are quite promising candidates for energy conversion devices. Herein, we have successfully synthesized PdCo alloy nanocubes supported on carbon nanobowl (denoted as Pd₂Co₁/CNB) nanohybrids by using the cyanogel auto-reduction method at high temperature. The morphology, composition and structure of Pd₂Co₁/CNB nanohybrids are characterized in detail, revealing that PdCo nanocubes have a high alloying degree and special {110} facets. In cyclic voltammetry measurements, Pd₂Co₁/CNB nanohybrids show a mass activity of 1089.0 A g _Pd^-1 and a specific activity of 40.03 mA cm^-2 for ethanol electrooxidation at peak potential, which are much higher than that of the commercial Pd/C electrocatalyst (278.2 A g_Pd^-1 and 8.22 mA cm^-2). Additionally, chronoamperometry measurements show that Pd₂Co₁/CNB nanohybrids have excellent durability for ethanol electrooxidation. A high alloying degree, special {110} facets and the CNB supporting material contribute to the high activity and durability of Pd₂Co₁/CNB nanohybrids, making them a highly promising Pt-alternative electrocatalyst for ethanol electrooxidation in DEFCs.

Mesoporous gold nanospheres via thiolate-Au(i) intermediates

This manuscript reports a facile yet effective surfactant-templated synthesis methodology to grow in situ metallic gold mesoporous nanospheres for methanol electrooxidation.

Mesoporous gold (mesoAu) nanospheres support enhanced (electro)catalytic performance owing to their three-dimensional (3D) interior mesochannels that expose abundant active sites and facilitate electron/mass transfers. Although various porous Nanostructured Au has been fabricated by electrochemical reduction, alloying–dealloying and hard/soft templating methods, successful synthesis of mesoAu nanospheres with tailorable sizes and porosities remains a big challenge. Here we describe a novel surfactant-directed synthetic route to fabricate mesoAu nanospheres with 3D interconnected mesochannels by using the amphiphilic surfactant of C₂₂H₄₅N⁺(CH₃)₂–C₃H₆–SH (Cl^–) (C₂₂N–SH) as the mesopore directing agent. C₂₂N–SH can not only self-reduce trivalent Au(iii)Cl₄^– to monovalent Au(i), but also form polymeric C₂₂N–S–Au(i) intermediates via covalent bonds. These C₂₂N–S–Au(i) intermediates facilitate the self-assembly into spherical micelles and inhibit the mobility of Au precursors, enabling the crystallization nucleation and growth of the mesoAu nanospheres via in situ chemical reduction. The synthetic strategy can be further extended to tailor the sizes/porosities and surface optical properties of the mesoAu nanospheres. The mesoAu nanospheres exhibit remarkably enhanced mass/specific activity and improved stability in methanol electrooxidation, demonstrating far better performance than non-porous Au nanoparticles and previously reported Au nanocatalysts. The synthetic route differs markedly from other long-established soft-templating approaches, providing a new avenue to grow metal nanocrystals with desirable nanostructures and functions.

Asymmetric Multimetallic Mesoporous Nanospheres

Mesoporous colloidal nanospheres with tailorable asymmetric nanostructures and multimetallic elemental compositions are building blocks in next-generation heterogeneous catalysts. Introducing structural asymmetry into metallic mesoporous frameworks has never been demonstrated, but it would be beneficial because the asymmetry enables the spatial control of catalytic interfaces, facilitates the electron/mass transfer and assists in the removal of poisonous intermediates. Herein, we describe a simple bottom-up strategy to generate uniform sub-100 nm multimetallic asymmetric bowl-shaped mesoporous nanospheres (BMSs). This method uses a surfactant-directed "dual"-template to control the kinetics of metal reduction on the surface of a vesicle, forming mesoporous metal islands on its surface whose spherical cone angle can be precisely controlled. The asymmetric BMS mesostructures with different spherical cone angles (structural asymmetries) and elemental compositions are demonstrated. The high surface area and asymmetric nature of the metal surfaces are shown to enhance catalytic performance in the alcohol oxidation reactions. The findings described here offer novel and interesting opportunities for rational design and synthesis of hierarchically asymmetric nanostructures with desired functions for a wide range of applications.

Encapsulating mesoporous metal nanoparticles: towards a highly active and stable nanoreactor for oxidative coupling reactions in water

We design and prepare a highly active and stable nanoreactor by encapsulating mesoporous metal nanoparticles for efficient production of α,β-unsaturated ketones via a one-pot oxidative coupling reaction.