Understanding the unorthodox stabilization of liquid phase exfoliated molybdenum disulfide (MoS2) in water medium

Direct or Indirect Sonication in Ecofriendly MoS2 Dispersion for NO2 and NH3 Gas-Sensing Applications

Unlike the most used, this study explores the effects of direct and indirect sonication methods on the dispersion and gas sensing performance of MoS2 nanoflakes. The obtained dispersions are characterized using various techniques, such as field emission scanning electron microscopy, high resolution transmission electron microscopy, atomic force microscopy, dynamic light scattering, and Raman and X-ray diffraction, to evaluate their morphological and structural properties. Gas sensing measurements are conducted using exfoliated MoS2 on interdigitated electrode structures, and the response to multiple gases is recorded. The sensitivity and selectivity of the sensors are analyzed and compared between the direct and indirect sonication methods. The results demonstrate that both direct and indirect methods lead to the formation of well-dispersed MoS2 multilayer nanosheets, whereas the indirect approach exhibits a uniform and bigger flake size. Gas sensing experiments reveal that the MoS2 nanoflakes prepared via indirect sonication have enhanced sensitivity by 17 and 46% toward NO2 and NH3 gases, respectively, compared to the ones achieved by the direct sonication method. Both methods demonstrated its selectivity for NO2 and NH3 and the preferential temperature to detect NO2 and NH3 gas are 50 and 100 °C, respectively. This research contributes to the development of eco-friendly MoS2-based gas sensors by providing insights into the influence of direct (probe) and indirect (bath) sonication methods on dispersion quality and gas sensing performance. The findings highlight the potential of indirect sonication as a reliable technique for fabricating high-performance MoS2 gas sensors, opening venues for the design and optimization of eco-friendly sensing platforms for environmental monitoring and industrial applications.

From Bulk Molybdenum Disulfide (MoS2) to Suspensions of Exfoliated MoS2 in an Aqueous Medium and Their Applications

Two-dimensional (2D) layered materials like graphene, transition-metal dichalcogenides (TMDs), boron nitrides, etc., exhibit unique and fascinating properties, such as high surface-to-volume ratio, inherent mechanical flexibility and robustness, tunable bandgap, and high carrier mobility, which makes them an apt candidate for flexible electronics with low consumption of power. Because of these properties, they are in tremendous demand for advancement in energy, environmental, and biomedical sectors developed through various technologies. The production and scalability of these materials must be sustainable and ecofriendly to utilize these unique properties in the real world. Here, in this current review, we review molybdenum disulfide (MoS2 nanosheets) in detail, focusing on exfoliated MoS2 in water and the applicability of aqueous MoS2 suspensions in various fields. The exfoliation of MoS2 results in the formation of single or few-layered MoS2. Therefore, this Review focuses on the few layers of exfoliated MoS2 that have the additional properties of 2D layered materials and higher excellent compatibility for integration than existing conventional Si tools. Hence, a few layers of exfoliated MoS2 are widely explored in biosensing, gas sensing, catalysis, photodetectors, energy storage devices, a light-emitting diode (LED), adsorption, etc. This review covers the numerous methodologies to exfoliate MoS2, focusing on the various published methodologies to obtain nanosheets of MoS2 from water solutions and their use.

Lignin-ultrasound method: Enhancement of antimicrobial capacity of MoS2-containing films

To improve the antimicrobial ability of MoS2-containing films, we used lignin and triple-frequency ultrasound for liquid-phase exfoliation (LPE) to obtain MoS2 nanosheets. Photoresponsive antimicrobial films with MoS2 nanosheets, lignin, polyvinyl alcohol and deep eutectic solvents were subsequently prepared. Lignin functionalized the MoS2 nanosheets by chemically linking with S in MoS2 and significantly improved the exfoliation efficiency. Tri-frequency ultrasound produces beneficial effects on the LPE process by creating a more homogeneous sound field and a stronger degree of cavitation. The concentration of MoS2 nanosheets in the exfoliating solution could reach 1.713 mg/mL under the effect of lignin-ultrasound. The antimicrobial ability of the films was analyzed, and the colony-forming units of E. coli and S. aureus could be reduced from 7 × 106 to 1 × 106 cfu/mL under the irradiation of infrared. The lignin in the film undergoes depolymerization and demethoxylation under the irradiation of infrared to have a more phenolic hydroxyl structure, which confers the growth inhibition ability of the films for bacteria that cannot be in close contact with the film. The method we used has some significance for the preparation of MoS2 nanosheets, and composite films prepared from MoS2, and lignin can be used in food packaging, wound antimicrobials, and other fields.

Photooxidative Behavior of Polystyrene Nanocomposites Filled with Two-Dimensional Molybdenum Disulfide

This study aimed to investigate how an ultralow content of a molybdenum disulfide (MoS₂) two-dimensional particle affects the photodegradation mechanism of polystyrene (PS). Here, an accelerated weathering study was presented on neat polystyrene and its nanocomposites produced with 0.001, 0.002, 0.003 and 0.005 wt% of molybdenum disulfide (MoS₂) exposed for various irradiation intervals (up to 8 weeks). The polymer photo-transformations were monitored using size exclusion chromatography (SEC), infrared spectroscopy (FTIR), and UV-Vis spectroscopy. The FTIR and UV/Vis results indicate that the PS degradation mechanism was not altered by the presence of MoS₂ particles; however, the degradation reactions were slowed down at higher MoS₂ contents (>0.003%). The SEC results proved the stabilizer effect due to MoS₂ particles, where M¯n, M¯w, and M¯w/M¯n values after 8 weeks were less modified when compared with the neat PS results. The MoS₂ acted as a UV stabilizer, and these two-dimensional particles acted by deactivating the free radicals generated by the PS matrix, even considering the low amount of the filler (<0.005 wt%).

Label-Free Electrochemiluminescence Nano-aptasensor for the Ultrasensitive Detection of ApoA1 in Human Serum

A molybdenum sulfide/zirconium oxide/Nafion (MoS₂/ZrO₂/Naf) based electrochemiluminescence (ECL) aptasensor for the selective and ultrasensitive detection of ApoA1 is proposed, with Ru(bpy)₃ ²⁺ as the luminophore. The chitosan (CS) modification on the nanocomposite layer allowed glutaraldehyde (GLUT) cross-linking, resulting in the immobilization of ApoA1 aptamers. Scanning electron microscopy, tunneling electron microscopy, and energy dispersive X-ray spectroscopy were used to characterize the nanocomposite, while electrochemiluminescence (ECL), cyclic voltammetry, and electrochemical impedance spectroscopy were used to analyze the aptasensor assembly. The nanocomposite was used as an electrode modifier, which increased the intensity of the ECL signal. Due to the anionic environment produced on the sensor surface following the specific interaction of the ApoA1 biomarker with the sensor, more Ru(bpy)₃ ²⁺ were able to be electrostatically attached to the aptamer-ApoA1 complex, resulting in enhanced ECL signal. The ECL aptasensor demonstrated outstanding sensitivity for ApoA1 under optimal experimental conditions, with a detection limit of 53 fg/mL and a wide linear dynamic range of 0.1-1000 pg/mL. The potential practical applicability of this aptasensor was validated by analyzing ApoA1 in human serum samples, with recovery rates of 94-108% (n = 3). The proposed assay was found to be substantially better compared to the commercially available enzyme-linked immunosorbent assay method, as reflected from over 1500 times improvement in the detection limit for ApoA1.

Efficient and Facile Synthetic Route of MoO3:MoS2 Hybrid Thin Layer via Oxidative Reaction of MoS2 Nanoflakes

In the present study, MoO₃:MoS₂ hybrid thin layers have been synthesized through partial oxidation of MoS₂. We have demonstrated that the reaction requires darkness conditions to decrease the oxidation rate, thus obtaining the hybrid, MoO₃:MoS₂. A simple liquid-phase exfoliation (LPE) is carried out to achieve homogenous MoS₂ nanoflakes and high reproducibility of the results after MoS₂ oxidation. XPS analyses reveal the presence of MoO₃, MoS₂, and MoOxSy in the hybrid layer. These results are also confirmed by X-ray diffraction and high-resolution TEM. Optical absorbance reveals that the absorption peaks of the MoO₃:MoS₂ hybrid are slightly redshifted with the appearance of absorption peaks in the near-infrared region due to the defects created after the oxidation reaction. The composition and atomic percentages of each component in the hybrid layer as a function of reaction time have also been reported to give perspective guides for improving electronic and optoelectronic devices based on 2D-MoS₂.

Photocatalytic activity of layered MoS2 in the reductive degradation of bromophenol blue

Molybdenum disulphide (MoS₂) is a layered material with interesting photocatalytic properties. In this study, a layered MoS₂ was produced using a hydrothermal method. The obtained material was characterised by XRD (X-ray diffraction), XPS (X-ray photoelectron spectroscopy), SEM (scanning electron microscopy), UV-Vis spectroscopy, DLS (dynamic light scattering), and zeta potential analysis. For the evaluation of the photocatalytic properties of layered MoS₂, a solution of bromophenol blue (BPB) and the catalyst was illuminated for 120 minutes. According to the experimental results, MoS₂ exhibited excellent catalytic activity in BPB degradation. The MoS₂ preparation method enabled improved light harvesting, avoided fast charge recombination (related to bulk MoS₂), and created a large number of suitable electron transfer sites for photocatalytic reactions. Simulation of BPB decay and bromide production was carried out for a further understanding of MoS₂ photocatalytic action. The simulation results proved the reduction mechanism of BPB photodegradation.

Molybdenum disulphide (MoS₂) is a layered material with interesting photocatalytic properties.

Combating Actions of Green 2D-Materials on Gram Positive and Negative Bacteria and Enveloped Viruses

Interactions of novel bi-dimensional nanomaterials and live matter such as bacteria and viruses represent an extremely hot topic due to the unique properties of the innovative nanomaterials, capable in some cases to exhibit bactericide and antiviral actions. The interactions between bacteria and viruses and two dimensional nanosheets are here investigated. We extensively studied the interaction between a gram-negative bacterium, Escherichia coli, and a gram-positive bacterium, Staphylococcus aureus, with two different types of 2D nanoflakes such as MoS₂, belonging to the Transition Metal Dichalcogenides family, and Graphene Oxide. The same two types of nanomaterials were employed to study their antiviral action toward the Herpes simplex virus type-1, (HSV-1). The experimental results showed different bactericide impacts as well as different antiviral power between the two nanomaterials. The experimental findings were interpreted in bacteria on the base of the Derjaguin–Landau–Verwey–Overbeek theory. A simple kinetic model of bacterial growth in the presence of the interacting nanosheets is also elaborated, to explain the observed results. The experimental results in viruses are really novel and somewhat surprising, evidencing a stronger antiviral action of Graphene Oxide as compared to MoS₂. Results in viruses are complicated to quantitatively interpret due to the complexity of the system under study, constituted by virus/host cell and nanoflake, and due to the lack of a well assessed theoretical context to refer to. Thus, these results are interpreted in terms of qualitative arguments based on the chemical properties of the interactors in the given solvent medium.

Thiolated poly(aspartic acid)-functionalized two-dimensional MoS2, chitosan and bismuth film as a sensor platform for cadmium ion detection

In this work, a sensitive electrochemical platform for determination of cadmium ions (Cd²⁺) is obtained using thiolated poly(aspartic acid) (TPA)-functionalized MoS₂ as a sensor platform by differential pulse anodic stripping voltammetry (DPASV). The performance of the TPA–MoS₂-modified sensor is systemically studied. It demonstrates that the TPA–MoS₂ nanocomposite modified sensor exhibits superior analytical performance for Cd²⁺ over a linear range from 0.5 μg L⁻¹ to 50 μg L⁻¹, with a detection limit of 0.17 μg L⁻¹. Chitosan is able to form a continuous coating film on the surface of the GC electrode. The good sensing performance of the TPA–MoS₂-modified sensor may be attributed to the following factors: the large surface area of MoS₂ (603 m² g⁻¹), and the abundant thiol groups of TPA. Thus, the TPA–MoS₂-modified sensor proves to be a reliable and environmentally friendly tool for the effective monitoring of Cd²⁺ existing in aquacultural environments.

In this work, a sensitive electrochemical platform for determination of cadmium ions (Cd²⁺) is obtained using thiolated poly(aspartic acid) (TPA)-functionalized MoS₂ as a sensor platform by differential pulse anodic stripping voltammetry (DPASV).