Effects of poly(ethylene glycol)-grafted graphene on the electrical properties of poly(lactic acid) nanocomposites

Polyethylene glycol embedded reduced graphene oxide supramolecular assemblies for enhanced room-temperature gas sensors

Herein, we present the gas-dependent electrical properties of a reduced graphene oxide nanocomposite. The reduced graphene oxide (rGO) was synthesized by reducing GO with sodium borohydride (NaBH4). As-synthesized rGO was dispersed in DI water containing 1, 2, 3, 4, and 5 wt% polyethylene glycol (PEG) to prepare PEG-rGO supramolecular assemblies. The successful preparation of supramolecular assemblies was verified by their characterization using XRD, FESEM, EDS, TEM, FTIR, and Raman spectroscopy. At room temperature, the gas-dependent electrical properties of these supramolecular assemblies were investigated. The results showed that sensors composed of PEG-rGO supramolecular assemblies performed better against benzene and methanol at 3% and 4% PEG, respectively. However, high selectivity and a wide range of activation energies (∼1.64-1.91 eV) were observed for H2 gas for 4% PEG-modified supramolecular assemblies. The PEG-rGO supramolecular assemblies may be an excellent candidate for constructing ultrahigh-performance gas sensors for a variety of applications due to their high sensitivity and selectivity.

Stable polyethylene glycol/biochar composite as a cost-effective photothermal absorber for 24 hours of steam and electricity cogeneration

Seawater desalination powered by solar energy is the most environmentally and economical solution in responding to the global water and energy crisis. However, solar desalination has been negatively impacted by intermittent sun radiation that alternates between day and night. In this study, sugarcane bagasse (SCB) was recycled via the pyrolysis process to biochar as a cost-effective solar absorber. Besides, polyethylene glycol (PEG) as a phase change material was encapsulated in the abundant pore structure of biochar to store the thermal energy for 24 hours of continuous steam generation. The BDB/1.5 PEG evaporator exhibited an evaporation rate of 2.11 kg m-2 h-1 (98.1% efficiency) under 1 sun irradiation. Additionally, the BDB/1.5 PEG evaporator incorporated by the TEC1-12706 module for continuous steam and electricity generation with a power density of 320.41 mW m-2. Moreover, 10 continuous hours of evaporation were applied to the composite demonstrating outstanding stability. The composite exhibited high water purification efficiency through solar desalination due to the abundant functional groups on the biochar surface. Finally, the resulting low-cost and highly efficient PCM-based absorber can be used on a wide scale to produce fresh water and energy.

Influence of the Micro-Nanostructuring of Titanium Dioxide Films on the Photocatalytic Degradation of Formic Acid under UV Illumination

Surface micro-nanostructuring can provide new functionalities and properties to coatings. For example, it can improve the absorption efficiency, hydrophobicity and/or tribology properties. In this context, we studied the influence of micro-nanostructuring on the photocatalytic efficiency of sol-gel TiO₂ coatings during formic acid degradation under UV illumination. The micro-nanostructuring was performed using the UV illumination of microspheres deposited on a photopatternable sol-gel layer, leading to a hexagonal arrangement of micropillars after development. The structures and coatings were characterized using Raman spectroscopy, ellipsometry, atomic force microscopy and scanning electron microscopy. When the sol-gel TiO₂ films were unstructured and untreated at 500 °C, their effect on formic acid’s degradation under UV light was negligible. However, when the films were annealed at 500 °C, they crystallized in the anatase phase and affected the degradation of formic acid under UV light, also depending on the thickness of the layer. Finally, we demonstrated that surface micro-nanostructuring in the form of nanopillars can significantly increase the photocatalytic efficiency of a coating during the degradation of formic acid under UV light.

Poly(Ethylene Glycol) Functionalized Graphene Oxide in Tissue Engineering: A Review on Recent Advances

Owing to the unique physical, chemical, mechanical and electrical properties, graphene and its derivatives have been extensively researched for diverse biomedical applications including in tissue engineering since the past decade. Tunable chemical functionalities of graphene oxide (GO), a graphene derivative, allow easy surface functionalization. Functionalization of GO with poly(ethylene glycol) (PEG) (PEG-GO) has received significant attention as it offers superior solubility, stability, and biocompatibility. Besides being an attractive candidate for drug delivery, PEG-GO can aid in the attachment, proliferation, and differentiation of stem cells, thereby augmenting tissue engineering. PEG-GO has shown excellent antibacterial efficacy, which could be an added advantage to minimize implant-associated infections. This review describes the synthesis techniques, properties, and biological potential of PEG-GO towards mammalian and bacterial cells. Studies wherein these nanomaterials have been explored for engineering various tissues are reviewed along with future opportunities in this field.

Polyethylene glycol grafted with carboxylated graphene oxide as a novel interface modifier for polylactic acid/graphene nanocomposites

Strength and toughness are both of great importance for the application of polylactic acid (PLA). Unfortunately, these two properties are often contradictory. In this work, an effective and practical strategy is proposed by using carboxylated graphene oxide (GC) grafted with polyethylene glycol (PEG), i.e. GC-g-PEG. The synthesis procedure of GC-g-PEG is firstly optimized. Then, a series of PLA nanocomposites were prepared by the melt blending method via masterbatch. In comparison to that achieved over pure PLA, these nanocomposites are of higher crystallinity, thermal stability and mechanical strength. This is mainly attributed to well-tailored interface and good dispersion. Especially, while retaining the tensile strength of the original PLA, the elongation at break increases by seven times by adding 0.3 wt% GC-g-PEG.

3D printed nanocomposites using polymer grafted graphene oxide prepared by multicomponent Passerini reaction

The surface of commercial graphene oxide was modified with polymers using Passerini reaction, which enhances the compatibility between nanoparticles and 3D printing resin.