Dual-functional SiOC ceramics coating modified carbon fibers with enhanced microwave absorption performance

Exfoliation Technology for Scalable Ligand-Free Core-Semishell Metal Nanoparticle Films

Core-shell metallic nanoparticles (NPs) are considered promising materials for their multifunctional properties. However, traditionally synthesized NPs have crucial issues that their ligands interfere with the direct interaction between NPs and neighboring materials, and it is very difficult to form a uniform film without the mixture of a template. In this article, we report an unprecedented exfoliation technology for fabricating a scalable ligand-free core-semishell metal NP film based on the evaporation system through a self-assembled monolayer-assisted surface energy control combined with a deep ultraviolet surface treatment around the core NPs. Owing to fabrication merits, the properties of the core-semishell NPs can be easily modulated depending on the shell material; the ligand-free core-shell NPs are directly attached to the surface of a material by Scotch tape, allowing interfacial interactions. Therefore, the proposed technique presents a new scientific method for studying interfacial interactions with heterogeneous materials and can be universally applied in optoelectronic devices, biopatches, photocatalysts, and so on.

Facile Preparation of Durable and Eco-Friendly Superhydrophobic Filter with Self-Healing Ability for Efficient Oil/Water Separation

The superhydrophobic feature is highly desirable for oil/water separation (OWS) operation to achieve excellent separation efficiency. However, using hazardous materials in fabricating superhydrophobic surfaces is always the main concern. Herein, superhydrophobic filters were prepared via an eco-friendly approach by anchoring silica particles (SiO2) onto the cotton fabric surface, followed by surface coating using natural material-myristic acid via a dip coating method. Tetraethyl orthosilicate (TEOS) was used in the synthesis of SiO2 particles from the silica sol. In addition, the impact of the drying temperature on the wettability of the superhydrophobic filter was investigated. Moreover, the pristine cotton fabric and as-prepared superhydrophobic cotton filters were characterised based on Fourier-transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS), scanning electron microscopy coupled with energy dispersive X-ray spectroscopy (SEM-EDX) and contact angle (CA) measurement. The superhydrophobic cotton filter was used to perform OWS using an oil-water mixture containing either chloroform, hexane, toluene, xylene or dichloroethane. The separation efficiency of the OWS using the superhydrophobic filter was as high as 99.9%. Moreover, the superhydrophobic fabric filter also demonstrated excellent durability, chemical stability, self-healing ability and reusability.

Rice straw derived graphene-silica based nanocomposite and its application in improved co-fermentative microbial enzyme production and functional stability

Cellulases are the one of the most highly demanded industrial biocatalysts due to their versatile applications, such as in the biorefinery industry. However, relatively poor efficiency and high production costs are included as the key industrial constraints that hinder enzyme production and utilization at economic scale. Furthermore, the production and functional efficiency of the β-glucosidase (BGL) enzyme is usually found to be relatively low among the cellulase cocktail produced. Thus, the current study focuses on fungi-mediated improvement of BGL enzyme in the presence of a rice straw-derived graphene-silica-based nanocomposite (GSNCs), which has been characterized using various techniques to analyze its physicochemical properties. Under optimized conditions of solid-state fermentation (SSF), co-fermentation using co-cultured cellulolytic enzyme has been done, and maximum enzyme production of 42 IU/gds FP, 142 IU/gds BGL, and 103 IU/gds EG have been achieved at a 5 mg concentration of GSNCs. Moreover, at a 2.5 mg concentration of nanocatalyst, the BGL enzyme showed its thermal stability at 60°C and 70 °C by holding its half-life relative activity for 7 h, while the same enzyme demonstrated pH stability at pH 8.0 and 9.0 for the 10 h. This thermoalkali BGL enzyme might be useful for the long-term bioconversion of cellulosic biomass into sugar.

Co-Carbonized Waste Polythene/Sugarcane Bagasse Nanocomposite for Aqueous Environmental Remediation Applications

The conversion of worthless municipal solid wastes to valuables is a major step towards environmental conservation and sustainability. This work successfully proposed a technique to utilize the two most commonly available municipal solid wastes viz polythene (PE) and sugarcane bagasse (SB) for water decolorization application. An SBPE composite material was developed and co-pyrolyzed under an inert atmosphere to develop the activated SBPEAC composite. Both SBPE and SBPEAC composites were characterized to analyze their morphological characteristics, specific surface area, chemical functional groups, and elemental composition. The adsorption efficacies of the composites were comparatively tested in the removal of malachite green (MG) from water. The SBPEAC composite had a specific surface area of 284.5 m²/g and a pore size of ~1.33 nm. Batch-scale experiments revealed that the SBPEAC composite performed better toward MG adsorption compared to the SBPE composite. The maximum MG uptakes at 318 K on SBPEAC and SBPE were 926.6 and 375.6 mg/g, respectively. The adsorption of MG on both composites was endothermic. The isotherm and kinetic modeling data for MG adsorption on SBPEAC was fitted to pseudo-second-order kinetic and Langmuir isotherm models, while Elovich kinetic and D-R isotherm models were better fitted for MG adsorption on SBPE. Mechanistically, the MG adsorption on both SBPE and SBPEAC composites involved electrostatic interaction, H-bonding, and π-π/n-π interactions.

Hybrid 1D/2D nanocarbon-based conducting polymer nanocomposites for high-performance wearable electrodes

A low interfacial contact resistance is a challenge in polymer nanocomposites based on conductive nanomaterials for high-performance wearable electrode applications. Herein, a polydimethylsiloxane (PDMS)-based flexible nanocomposite incorporating high-conductivity 1D single-walled carbon nanotubes (SWCNTs) and 2D reduced graphene oxide (r-GO) was developed for high-performance electrocardiogram (ECG) wearable electrodes. A PDMS-SWCNT (P-SW; type I) nanocomposite containing only SWCNTs (2 wt%), exhibited rough and non-uniform surface morphology owing to the strong bundling effect of as-grown SWCNTs and randomly entangled aggregate structures and because of inefficient vacuum degassing (i.e., R _P-SW = 1871 Ω). In contrast, owing to the hybrid structure of the SWCNTs (1 wt%) and r-GO (1 wt%), the PDMS-SWCNTs/r-GO (P-SW/r-GO; type II) nanocomposite exhibited uniform surface characteristics and low contact resistance (i.e., R _P-SW/r-GO = 63 Ω) through the formation of hybrid and long conducting pathways. The optimized nanocomposite (P-SW/r-GO/f; type III) possessed a fabric-assisted structure that enabled tunable and efficient vacuum degassing and curing conditions. Additionally, a long and wide conducting pathway was formed through more uniform and dense interconnected structures, and the contact resistance was drastically reduced (i.e., R _P-SW/r-GO/f = 15 Ω). The performance of the electrodes fabricated using the optimized nanocomposites was the same or higher than that of commercial Ag/AgCl gel electrodes during real-time measurement for ECG Bluetooth monitoring. The developed high-performance hybrid conducting polymer electrodes are expected to contribute significantly to the expansion of the application scope of wearable electronic devices and wireless personal health monitoring systems.

Clean Process to Utilize the Potassium-Containing Phosphorous Rock with Simultaneous HCl and KCl Production via the Steam-Mediated Reactions

In this paper, a clean process based on the steam-mediated reactions for simultaneous HCl and KCl production using the potassium (K)-containing phosphorous rock as a precursor is proposed. Through hydrochloric acid (HCl) leaching, not only the generation of H₃PO₄ and CaCl₂ (via further precipitation) were realized but also the acid-insoluble residue [phosphorous-rock slag (PS)] rich in elements, that is, K, Al, Si, and so on, in the form of microcline (KAlSi₃O₈) and quartz (SiO₂) was obtained and became readily available for further HCl and KCl generation. Over 95% of the elements, that is, K, Al, and Si, come into the final products, and the overall acid consumption (based on HCl) is significantly reduced (90%) due to recovery of acids. The impacts of the key operational parameters such as temperature, duration, and reagent impregnate ratio were rigorously analyzed via a supervised machine learning approach, and the optimal conditions were determined [reaction temperature, X₁, 850 °C; reaction duration, X₂, 40 min; and impregnate ratio (PS over CaCl₂), X₃, 2.5] with approximately ±10% uncertainties. Thermodynamic analysis indicates that the introduction of steam to PS + CaCl₂ not only enhances the chemical potential for the formation of HCl and KCl but also provides the transport advantage in continuously removing the generated products, that is, HCl and KCl, out of the system. Molecular simulation indicates that the presence of both steam and SiO₂ in the PS matrix plays critical roles in decomposing PS + CaCl₂ at high temperature. The shrinking core model shows that both the intrinsic kinetics and transport are influential with the activation energy being around 14.63 kJ/mol. The potential reaction pathway is postulated.

Enhanced Li-Ion Rate Capability and Stable Efficiency Enabled by MoSe2 Nanosheets in Polymer-Derived Silicon Oxycarbide Fiber Electrodes

Transition metal dichalcogenides (TMDs) such as MoSe₂ have continued to generate interest in the engineering community because of their unique layered morphology—the strong in-plane chemical bonding between transition metal atoms sandwiched between two chalcogen atoms and the weak physical attraction between adjacent TMD layers provides them with not only chemical versatility but also a range of electronic, optical, and chemical properties that can be unlocked upon exfoliation into individual TMD layers. Such a layered morphology is particularly suitable for ion intercalation as well as for conversion chemistry with alkali metal ions for electrochemical energy storage applications. Nonetheless, host of issues including fast capacity decay arising due to volume changes and from TMD’s degradation reaction with electrolyte at low discharge potentials have restricted use in commercial batteries. One approach to overcome barriers associated with TMDs’ chemical stability functionalization of TMD surfaces by chemically robust precursor-derived ceramics or PDC materials, such as silicon oxycarbide (SiOC). SiOC-functionalized TMDs have shown to curb capacity degradation in TMD and improve long term cycling as Li-ion battery (LIBs) electrodes. Herein, we report synthesis of such a composite in which MoSe₂ nanosheets are in SiOC matrix in a self-standing fiber mat configuration. This was achieved via electrospinning of TMD nanosheets suspended in pre-ceramic polymer followed by high temperature pyrolysis. Morphology and chemical composition of synthesized material was established by use of electron microscopy and spectroscopic technique. When tested as LIB electrode, the SiOC/MoSe₂ fiber mats showed improved cycling stability over neat MoSe₂ and neat SiOC electrodes. The freestanding composite electrode delivered a high charge capacity of 586 mAh g⁻¹_electrode with an initial coulombic efficiency of 58%. The composite electrode also showed good cycling stability over SiOC fiber mat electrode for over 100 cycles.

Ultrahigh-strength carbon aerogels for high temperature thermal insulation

Carbon aerogels with nanoporous structure are attractive for thermal insulation under extreme conditions, but their practical applications are usually plagued by the inherent brittleness and easy-oxidation characteristic at high temperature. Herein, silica-modified carbon aerogels (SCAs) with extraordinarily high strength are prepared via a facile sol-gel polymerization of phenolic resin and siloxane, followed by ambient pressure drying and carbonization. The resulting SCAs possess medium-high density of ∼0.5 g·cm^-3 and mesoporous structure with the mean pore size of 33 nm. During carbonization process, the siloxane could be gradually transformed into the amorphous SiO₂ particles and crystalline SiC particles, which are coated on the surface of carbon nanoparticle and consequently improve the oxidation-resistance of carbon aerogels. Due to the density-porosity trade-off, the SCAs have high compressive strength of 10.0 MPa and satisfied thermal conductivities of 0.118 W·m^-1·K^-1 at 25 °C and 0.263 W·m^-1·K^-1 at 1000 °C. Furthermore, needled carbon fiber-reinforced SCAs (CF-SCAs) with ultrahigh compressive strength of 210.5 MPa are prepared, which exhibit good thermal conductivities of 0.207 W·m^-1·K^-1 at 25 °C and 0.407 W·m^-1·K^-1 at 1000 °C. The ultrahigh mechanical strength, good oxidation-resistance, good thermal insulation as well as the facile preparation make the SACs great promising in high-temperature insulations especially under harsh conditions.

Surface Modification of Carbon Nanofibers to Improve Their Biocompatibility in Contact with Osteoblast and Chondrocytes Cell Lines

The goal of this study is to investigate the influence of different types of modifiers, such as sodium hyaluronate (NaH), graphene oxide (GO), silica oxycarbide (SiOC) and oxidation process (ox) on physicochemical, morphological, and biological properties of electrospun carbon nanofibers (eCNFs). Scanning electron microscopy, X-ray photoelectron spectroscopy and infrared spectroscopy (FTIR) were used to evaluate the microstructure and chemistry of as-prepared and modified CNFs. The electrical properties of CNFs scaffolds were examined using a four-point probe method to evaluate the influence of modifiers on the volume conductivity and surface resistivity of the obtained samples. The wettability of the surfaces of modified and unmodified CNFs scaffolds was also tested by contact angle measurement. During the in vitro study all samples were put into direct contact with human chondrocyte CHON-001 cells and human osteosarcoma MG-63 cells. Their viability was analysed after 72 h in culture. Moreover, the cell morphology and cell area in contact with CNFs was observed by means of fluorescence microscopy. The obtained results show great potential for the modification of CNFs with polymer, ceramic and carbon modifiers, which do not change the fiber form of the substrate but significantly affect their surface and volume properties. Preliminary biological studies have shown that the type of modification of CNFs affects either the rate of increase in the number of cells or the degree of spreading in relation to the unmodified sample. More hydrophilic and low electrically conductive samples such as CNF_ox and CNF_NaH significantly increase cell proliferation, while other GO and SiOC modified samples have an effect on cell adhesion and thus cell spreading. From the point of view of further research and the possibility of combining the electrical properties of modified CNF scaffolds with electrical stimulation, where these scaffolds would be able to transport electrical signals to cells and thus affect cell adhesion, spreading, and consequently tissue regeneration, samples CNF_GO and CNF_SiOC would be the most desirable.

Single-pot template-free synthesis of a glycerol-derived C–Si–Zr mesoporous composite catalyst for fuel additive production

The C–Si–Zr material synthesized from bio-derived waste glycerol, ZrO(NO₃)₂ and TEOS exhibits excellent catalytic activity for tri-acetin production from low-value glycerol.