Development of a magnetic nanocomposite sorbent (NiCoMn/Fe3O4@C) for efficient extraction of methylene blue and Auramine O

A rapid and efficient method for the simultaneous monitoring and recovery of Auramine O (AO) and Methylene Blue (MB) dyes from water samples is presented. This method, named ultrasound-assisted dispersive-magnetic nanocomposites-solid-phase microextraction (UA-DMN-μSPE), utilizes NiCoMn/Fe3O4@C composite sorbents. Response surface methodology (RSM) combined with artificial neural networks (ANN) and generalized regression artificial neural network (GRNN) under central composite design (CCD) was employed to optimize various parameters for efficient extraction, followed by further refinement using desirability function analysis (DFA) and genetic algorithms (GA). Under optimized conditions, the method achieved exceptional recovery rates (99.5 ± 1.2% for AO and 99.8 ± 1.1% for MB) with acetone as the eluent. Additionally, a high preconcentration factor of 45.50 and 47.30 for AO and MB, respectively, was obtained. Low detection limits of 0.45 ng mL⁻1 (AO) and 1.80 ng mL⁻1 (MB) were achieved with wide linear response ranges (5-1000 and 5-2000 ng mL⁻1 for AO and MB, respectively). The method exhibited good stability with RSDs below 3% for five recycling runs, and minimal interference from various ions was observed. This UA-DMN-μSPE-UV/Vis method offers significant advantages in terms of efficiency, preconcentration, and detection limits, making it a valuable tool for the analysis of AO and MB in water samples.

Fe3O4@UiO-66-NH2 based on magnetic solid phase extraction for determination of organic UV filters in environmental water samples

In this work, a nanocomposite structured magnetic metal-organic framework named as Fe3O4@UiO-66-NH2 was prepared via a simple hydrothermal approach. The as-mentioned nanocomposite was characterized by Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction analysis (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and the Brunauer-Emmett-Teller (BET) techniques. Using the Fe3O4@UiO-66-NH2 as a nanosorbent, an easy and highly effective approach was developed to preconcentrate nine organic UV filters before gas chromatography-mass spectrometry (GC-MS) analysis. Different conditions influencing the extraction efficiency encompassing the sorbent amount, nature and volume of desorption solvent, desorption time, pH of the sample, and extraction time, were examined. Under the optimal experimental parameters, the Fe3O4@UiO-66-NH2-based magnetic solid phase extraction and GC-MS (MSPE-GC-MS) demonstrated linearity in the range of 0.03-1500 ng/L (R2 ≥ 0.9974) and the reproducibility, expressed as RSD, was ≤7.5%. The limits of detection ranged between 0.01 and 0.07 ng/L and limits of quantification were in the range of 0.03-0.4 ng/L. Finally, the suggested approach was satisfactorily utilized to determine nine organic UV filters in different water samples (analytical recoveries between 86.5% and 104.2%).

Advanced porous organic materials for sample preparation in pharmaceutical analysis

The development of novel sample preparation media plays a crucial role in pharmaceutical analysis. To facilitate the extraction and enrichment of pharmaceutical molecules in complex samples, various functionalized materials have been developed and prepared as adsorbents. Recently, some functionalized porous organic materials have become adsorbents for pharmaceutical analysis due to their unique properties of adsorption and recognition. These advanced porous organic materials, combined with consequent analytical techniques, have been successfully used for pharmaceutical analysis in complex samples such as environmental and biological samples. This review encapsulates the progress of advanced porous materials for pharmaceutical analysis including pesticides, antibiotics, chiral drugs, and other compounds in the past decade. In addition, we also address the limitations and future trends of these porous organic materials in pharmaceutical analysis.

Efficient removal of veterinary drugs from aqueous solutions using magnetically separable carbonaceous materials derived from cobalt and iron metal-organic frameworks

Rapid synthesis of carbon-based magnetic materials derived from cobalt and iron metal-organic frameworks (MOFs), ZIF-67, and MIL-100(Fe), by microwave-assisted method, followed by carbonization under a N₂ atmosphere is described in this study. The carbon-derived MOFs (CDMs) were evaluated for the removal of the emerging pollutants sulfadiazine (SDZ) and flumequine (FLU) used as veterinary drugs. The study aimed to link the adsorption behavior with their surface properties and elemental composition. C-ZIF-67 and C-MIL-100(Fe) showed hierarchical porous structures with specific surface areas of 295.6 and 163.4 m² g^-1, respectively. The Raman spectra of the CDMs show the characteristic D and G bands associated with defect-rich carbon and sp² graphitic carbon, respectively. The CDMs exhibit cobalt species (Co₃O₄, CoO, and Co) in C-ZIF-67 and iron species (Fe₂O₃, Fe₃O₄, and Fe) in C-MIL-100 (Fe) which are related to the magnetic behavior of CDMs. C-ZIF-67 and C-MIL-100 (Fe) had saturation magnetization values of 22.9 and 53.7 emu g^-1, respectively, allowing easy solid-liquid separation using a magnet. SDZ and FLU removal rates on CDMs follow pseudo-second-order kinetics, and adsorption isotherms fit the Langmuir model based on regression coefficient values. Adsorption thermodynamics calculations showed that the adsorption of SDZ and FLU by CDMs was a thermodynamically favorable process. Therefore, these properties of C-ZIF-67 and C-MIL-100 (Fe) and their regeneration ability facilitate their use as adsorbents for emerging pollutants.

CO2 Capture from High-Humidity Flue Gas Using a Stable Metal–Organic Framework

The flue gas from fossil fuel power plants is a long-term stable and concentrated emission source of CO2, and it is imperative to reduce its emission. Adsorbents have played a pivotal role in reducing CO2 emissions in recent years, but the presence of water vapor in flue gas poses a challenge to the stability of adsorbents. In this study, ZIF-94, one of the ZIF adsorbents, showed good CO2 uptake (53.30 cm3/g), and the calculated CO2/N2 (15:85, v/v) selectivity was 54.12 at 298 K. Because of its excellent structural and performance stability under humid conditions, the CO2/N2 mixture was still well-separated on ZIF-94 with a separation time of 30.4 min when the relative humidity was as high as 99.2%, which was similar to the separation time of the dry gas experiments (33.2 min). These results pointed to the enormous potential applications of ZIF-94 for CO2/N2 separation under high humidity conditions in industrial settings.

Removal of sulfanilamide by tailor-made magnetic metal-ceramic nanocomposite adsorbents

Three tailor-made magnetic metal-ceramic nanocomposites, obtained from zeolite A (ZA1 and ZA2) and a natural clinoptilolite (LB1), have been used as adsorbents to remove sulfanilamide (SA), a sulfonamide antibiotic of common use, from water. A patented process for the synthesis of nanocomposites has been suitably modified to maximize the efficiency of the SA removal, as well as to extend the applicability of the materials. The role played by the main process parameters (kinetic, pH, initial concentration of SA) has been characterized. The significant effect of the pH on the SA removal has been explained identifying two possibly coexisting mechanisms of SA adsorption, based on polar and hydrophobic interactions, respectively. The adsorption kinetics have been in all cases described by the pseudo second-order model. The adsorption isotherms obtained with ZA1 have been satisfactorily described by the Langmuir model, suggesting a monolayer adsorption of SA on the magnetic nanocomposites resulting from a uniform surface energy. The isotherms obtained with LB1 could be described by a more complex approach, deriving by the additive superposition of Langmuir and Sips models. In order to ensure an effective removal of the antibiotic and a proper recycle of the magnetic adsorbents, a sustainable regeneration procedure of the exhausted adsorbent has been developed, based on the treatment with a dilute solution of NaOH.

Room temperature fabrication of magnetic covalent organic frameworks for analyzing sulfonamide residues in animal-derived foods

A magnetic solid phase extraction method based on magnetic covalent organic frameworks (TpBD@Fe₃ O₄ ) combined with high performance liquid chromatography has been developed to detect the sulfonamides including sulfadiazine, sulfamerazine, sulfamethazine and sulfamethoxazole in milk and meat. TpBD@Fe₃ O₄ were synthesized at room temperature under mild reaction conditions with a simple and rapid operation. The TpBD@Fe₃ O₄ exhibited higher extraction efficiency because of the π-π and electrostatic interactions between the benzene ring structure of the TpBD and the SA molecules. The extraction conditions including the dosage of adsorbents, the type and dosage of eluent, the elution time and the pH of the sample solution were fully optimized. The detection results showed good linearity over a wide range (50-5×10⁴ ng/mL) and low detection limits (3.39-5.77 ng/mL) for the SA targets. The practicability of this MSPE-HPLC method was further evaluated by analyzing milk and meat samples, with recoveries of the targets of 71.6%-110.8% in milk and 71.9%-109.7% in pork. The successful detection of SAs residues has demonstrated the TpBD@Fe₃ O₄ excellent practical potential for analyzing pharmaceutical residues in animal-derived foods. This article is protected by copyright. All rights reserved.

Metal organic framework derived Zn/N co-doped hydrophilic porous carbon for efficient solid phase microextraction of polar phenols

MOF-derived zink and nitrogen co-doped porous carbon (ZNPC) was synthesized through the pyrolysis of MOF-5-NH₂ and used as a solid-phase microextraction (SPME) coating material. Coupled with gas chromatography-mass spectrometry (GC-MS), headspace SPME (HS-SPME) based on ZNPC was adopted for the determination of phenols in food samples. The co-existence of N and Zn in ZNPC endows the derived carbon superior hydrophilicity, which is highly beneficial for phenols capture. After optimizing the conditions of extraction and desorption, a sensitive analytical method was established with low limits of detections (LODs, 0.73-2.3 ng g^-1) and wide linear ranges (5-5000 ng g^-1). Both the intra-fiber repeatability (RSDs from 2.8-7.3%) and inter-fiber reproducibility (RSDs from 9.7-11.7%) were satisfactory. The established method was applied to phenol determination in beef jerky and duck neck with satisfactory recoveries of 81.2-120.4% and RSDs of 2.8-9.9%, which met well with the requirement of practical application.

Covalent-coordination tandem functionalization of a metal-organic framework (UiO-66) as a hybrid probe for luminescence detection of trans,trans-muconic acid as a biomarker of benzene and Fe3

By means of post-synthetic treatment on the UiO-66 derivative with -SO3H, a novel luminescent hybrid material named Tb3+@UiO-66-SO3H has been prepared simply and efficiently. Given its wonderful luminescence properties like intense green emission, a long lifetime, a robust structure and photostability, it is further developed as a fluorescent probe for the sensing of trans,trans-muconic acid (tt-MA, a biomarker of benzene) and Fe3+, which are closely related to human health. Notably, Tb3+@UiO-66-SO3H shows an outstanding recognition ability for Fe3+ among common cations with a low detection limit (0.11 μM, 0.006 ppm). More importantly, Tb3+@UiO-66-SO3H can realize highly sensitive and selective detection of tt-MA (detection limit, 0.58 μM, 0.083 ppm). Besides, this rapid response probe is facilely prepared, non-toxic and reusable, showing the potential of Tb3+@UiO-66-SO3H in the practical monitoring of tt-MA and Fe3+.

Sulfadiazine, sulfamethazine and sulfachloropyridazine removal using three different porous materials: Pine bark, "oak ash" and mussel shell

This work focuses on studying the efficacy of three different by-products to adsorb three antibiotics (sulfadiazine, SDZ; sulfamethazine, SMT; sulfachloropyridazine, SCP). These antibiotics can be considered pollutants of the environment when they reach water, as well as in cases where they are spread on soils through irrigation or contained in sewage sludge or livestock manure. In this study, batch-type adsorption/desorption experiments were performed for each of the three sulfonamides, adding 7 different concentrations of the antibiotics, going from 1 to 50 μmol L^-1, and with contact time of 24 h. The results indicate that pine bark is the most efficient bioadsorbent among those studied, as it adsorbs up to 95% of the antibiotics added, while desorption is always less than 11%. However, for "oak ash" and mussel shell the adsorption is always lower than 45 and 15%, respectively, and desorption is high, reaching up to 49% from "oak ash" and up to 81% from mussel shell. Adsorption data showed good fitting to the Linear and Freundlich models, with R² values between 0.98 and 1.00 in both cases. K_d and K_F adsorption parameters showed similar values for the same sorbent materials but were much higher for pine bark than for the other two bioadsorbents. The Freundlich's n parameter showed values in the range 0.81-1.28. The highest K_F values (and therefore the highest adsorption capacities) were obtained for the antibiotic SCP in pine bark. Pine bark showed the highest capacity to adsorb each of the antibiotics, increasing as a function of the concentration added. When the concentration of sulfonamide added was 50 μM, the amounts adsorbed were 780 μmol kg^-1 for SDZ, 890 μmol kg^-1 for SMT, and 870 μmol kg^-1 for SCP. "Oak ash" and mussel shell have low adsorption capacity for all three sulfonamides, showing values always lower than 150 μmol kg^-1 (oak ash) and 20 μmol kg^-1 (mussel shell) when a concentration of 50 μmol L^-1 of antibiotic is added. The results of this study could aid to make an appropriate management of the by-products studied, in order to facilitate their valorization and recycling in the treatment of environmental compartments polluted with sulfonamide antibiotics.

Enhanced Degradation of Sulfonamide Antibiotics by UV Irradiation Combined with Persulfate

In this study, the degradation of sulfonamide antibiotics was investigated through persulfate-enhanced UV advanced oxidation process. Factors that may affect the degradation efficiency were analyzed. Results showed that the persulfate imposed a significant enhancement on the UV oxidation process during the sulfathiazole degradation. The combined process of UV/persulfate can effectively remove about 96% of sulfathiazole within 60 min. With the increase in the dosage of persulfate, the removal efficiency increased as well. Different water matrix almost had no effect on the removal efficiency. Two intermediates were found during the sulfathiazole degradation. It can be predicted that the combined process of UV/persulfate has a broad application prospect for removing sulfonamide antibiotics in water treatment.

Synthesis of Magnetic Metal-Organic Frame Material and Its Application in Food Sample Preparation

A variety of contaminants in food is an important aspect affecting food safety. Due to the presence of its trace amounts and the complexity of food matrix, it is very difficult to effectively separate and accurately detect them. The magnetic metal-organic framework (MMOF) composites with different structures and functions provide a new choice for the purification of food matrix and enrichment of trace targets, thus providing a new direction for the development of new technologies in food safety detection with high sensitivity and efficiency. The MOF materials composed of inorganic subunits and organic ligands have the advantages of regular pore structure, large specific surface area and good stability, which have been thoroughly studied in the pretreatment of complex food samples. MMOF materials combined different MOF materials with various magnetic nanoparticles, adding magnetic characteristics to the advantages of MOF materials, which are in terms of material selectivity, biocompatibility, easy operation and repeatability. Combined with solid phase extraction (SPE) technique, MMOF materials have been widely used in the food pretreatment. This article introduced the new preparation strategies of different MMOF materials, systematically summarizes their applications as SPE adsorbents in the pretreatment of food contaminants and analyzes and prospects their future application prospects and development directions.