Nanobowtie arrays with tunable materials and geometries fabricated by holographic lithography

A cavity induced mode hybridization plasmonic sensor for portable detection of exosomes

Exosomes have been considered as promising biomarkers for cancer diagnosis due to their abundant information from originating cells. However, sensitive and reliable detection of exosomes is still facing technically challenges due to the lack of a sensing platform with high sensitivity and reproducibility. To address the challenges, here we propose a portable surface plasmon resonance (SPR) sensing of exosomes with a three-layer Au mirror/SiO2 spacer/Au nanohole sensor, fabricated by an economical polystyrene nanosphere self-assembly method. The SiO2 spacer can act as an optical cavity and induce mode hybridization, leading to excellent optimization of both sensitivity and full width at half maximum compared with normal single layer Au nanohole sensors. When modified with CD63 or EpCAM aptamers, a detection of limit (LOD) of as low as 600 particles/μL was achieved. The sensors showed good capability to distinguish between non-tumor derived L02 exosomes and tumor derived HepG2 exosomes. Additionally, high reproducibility was also achieved in detection of artificial serum samples with RSD as low as 2%, making it feasible for clinical applications. This mode hybridization plasmonic sensor provides an effective approach to optimize the detection sensitivity of exosomes, pushing SPR sensing one step further towards cancer diagnosis.

Bowtie Nanoantenna LSPR Biosensor for Early Prediction of Preeclampsia

OBJECTIVE

The concentration of the placental circulating factor in early pregnancy is often extremely low, and the traditional prediction method cannot meet the clinical demand for early detection preeclampsia in high-risk gravida. It is of prime importance to seek an ultra-sensitive early prediction method.

METHODS

In this study, finite-different time-domain (FDTD) and Discrete Dipole Approximation (DDA) simulation, and electron beam lithography (EBL) methods were used to develop a bowtie nanoantenna (BNA) with the best field enhancement and maximum coupling efficiency. Bio-modification of the placental circulating factor (sFlt-1, PLGF) to the noble nanoparticles based on the amino coupling method were explored. A BNA LSPR biosensor which can specifically identify the placental circulating factor in preeclampsia was constructed.

RESULTS

The BNA LSPR biosensor can detect serum placental circulating factors without toxic labeling. Serum sFlt-1 extinction signal (Δλmax) in the preeclampsia group was higher than that in the normal pregnancy group (14.37 ± 2.56 nm vs. 4.21 ± 1.36 nm), p = 0.008, while the serum PLGF extinction signal in the preeclampsia group was lower than that in the normal pregnancy group (5.36 ± 3.15 nm vs. 11.47 ± 4.92 nm), p = 0.013. The LSPR biosensor detection results were linearly consistent with the ELISA kit.

CONCLUSIONS

LSPR biosensor based on BNA can identify the serum placental circulating factor of preeclampsia with high sensitivity, without toxic labeling and with simple operation, and it is expected to be an early detection method for preeclampsia.

Development of the multi-directional ablation process using the femtosecond laser to create a pattern on the lateral side of a 3D microstructure

Two-photon stereolithography (TPS) is widely used for the fabrication of various three-dimensional (3D) structures with sub-micron fabrication resolution in a single fabrication process. However, TPS is unsuitable for microstructures with fine-hole patterns. The laser ablation process can be easily drilled, or made holes in various materials. However, in the case of laser ablation, the focal plane of the laser is fixed, which is limited to the processing plane. In this study, a multidirectional ablation process is studied to apply laser ablation to various processing planes of a 3D microstructure fabricated by the TPS process. A 3D hybrid fabrication process with the advantages of both TPS and laser ablation is expected to improve the fabrication efficiency. The 3D hybrid process is proposed based on a single laser source. The microstructure is fabricated using TPS, and the multi-directional ablation process creates a hole in the lateral side of the 3D microstructure. To develop the multidirectional ablation process, the reflecting mirror system should be designed to adaptably rotate the laser focal plane and guide the laser path for the target process plane. Through various examples, we demonstrate the ability of the multi-directional ablation process with various examples.

Error analysis and realization of a phase-modulated diffraction grating used as a displacement sensor

A grating-based interferometric cavity produces coherent diffraction light field in a compact size, serving as a promising candidate for displacement measurement by taking advantage of both high integration and high accuracy. Phase-modulated diffraction gratings (PMDGs) make use of a combination of diffractive optical elements, allowing for the diminishment of zeroth-order reflected beams and thus improving the energy utilization coefficient and sensitivity of grating-based displacement measurements. However, conventional PMDGs with submicron-scale features usually require demanding micromachining processes, posing a significant challenge to manufacturability. Involving a four-region PMDG, this paper establishes a hybrid error model including etching error and coating error, thus providing a quantitative analysis of the relation between the errors and optical responses. The hybrid error model and the designated process-tolerant grating are experimentally verified by micromachining and grating-based displacement measurements using an 850 nm laser, confirming the validity and effectiveness. It is found the PMDG achieves an energy utilization coefficient (the ratio of the peak-to-peak value of the ±1st order beams to the 0th-order beam) improvement of nearly 500% and a four-fold reduction in 0th-order beam intensity compared with the traditional amplitude grating. More importantly, this PMDG maintains very tolerant process requirements, and the etching error and coating error can be up to 0.5 µm and 0.6 µm, respectively. This offers attractive alternatives to the fabrication of PMDGs and grating-based devices with wide process compatibility. This work first systematically investigates the influence of fabrication errors and identifies the interplay between the errors and the optical response for PMDGs. The hybrid error model allows further avenues for the fabrication of diffraction elements with practical limitations of micromachining fabrication.

Large Area Patterning of Highly Reproducible and Sensitive SERS Sensors Based on 10-nm Annular Gap Arrays

Applicable surface-enhanced Raman scattering (SERS) active substrates typically require low-cost patterning methodology, high reproducibility, and a high enhancement factor (EF) over a large area. However, the lack of reproducible, reliable fabrication for large area SERS substrates in a low-cost manner remains a challenge. Here, a patterning method based on nanosphere lithography and adhesion lithography is reported that allows massively parallel fabrication of 10-nm annular gap arrays on large areas. The arrays exhibit excellent reproducibility and high SERS performance, with an EF of up to 10⁷. An effective wearable SERS contact lens for glucose detection is further demonstrated. The technique described here extends the range of SERS-active substrates that can be fabricated over large areas, and holds exciting potential for SERS-based chemical and biomedical detection.

Nonlocal means filter based on cosine similarity applied in speckle reduction of digital holography

In the field of digital holography, the speckle caused by coherent light greatly disturbs the quality of the reconstruction. This paper presents an innovative method to efficiently reduce speckle noise with a nonlocal means filter based on cosine similarity that determines the weight of each traversal pixel to the target pixel by comparing the similarity between the target pixel neighborhood and the traversal pixel neighborhood. Experimental results with qualitative and quantitative analysis indicate that the proposed method significantly improves noise reduction performance while preserving the details of the original image. Compared with other general image-processing methods, this well-directed method is more in line with the characteristics of holographic speckle noise and has obvious advantages in various metrics.

Study of the Fabrication of Gold Nanoparticle-Graphene-Arrayed Micro/Nanocavities as SERS Substrates Compared to Two Different Angles of Triangular Pyramid Tips

Surface-enhanced Raman scattering (SERS) has attracted attention because of its enormous potential to detect molecules with low concentrations. The method of fabricating SERS substrates is of great importance for improving the detection resolution. However, SERS substrates with different triangular pyramid tips fabricated by using the tip-based nanoindentation method has not been reported. Here, we prepared arrayed micro/nanocavities on copper-based graphene using the continuous indentation method with a Berkovich tip and a cube-corner tip, which have different face angles. Gold nanoparticles were then sputtered onto the graphene-copper micro/nanocavities to form the Au@GR@Cu micro/nanocavities SERS substrates. The substrates formed using the Berkovich tip and cube-corner tip were labeled B2-B9 and C2-C9, respectively, in which the numbers indicate the machining feed. Rhodamine 6G (R6G) was employed, and the Raman intensities of R6G on the differently arrayed Au@GR@Cu micro/nanocavities were measured. The Raman intensities of R6G were stronger on the pile-ups than on the inverted triangular pyramid cavities. The Raman intensities of R6G were highest on the C2 and B2 structures and lowest on the C9 and B9 structures. The Raman intensities of R6G on the arrayed Au@GR@Cu micro/nanocavities fabricated by the cube-corner tip were stronger than those on the arrayed Au@GR@Cu micro/nanocavities fabricated using the Berkovich tip with the same machining feed. In addition, the electric field intensity and distribution of the B9 and C9 arrayed Au@GR@Cu were simulated using Comsol software. Au@GR@Cu structures fabricated by the cube-corner tip were generated with higher electric field intensities. Furthermore, the relative standard deviations at 1362 cm^-1 of R6G were 6.19 and 6.62% on the C2 and C4 surfaces, respectively, showing good homogeneity. The SERS spectra of 10^-9 mol/L malachite green solution and 10^-6 mol/L carbaryl solution were recognized on the C1, C2, and C4 surfaces on day 1 and after 3 months, respectively. After storage at room temperature for 3 months, the reductions in the Raman intensities were less than 10%, indicating excellent stability. The results showed that the arrayed Au@GR@Cu micro/nanocavities fabricated using the cube-corner tip performed better than those fabricated using the Berkovich tip and exhibited excellent uniformity, availability, and stability, providing great potential for detecting pesticides at low concentrations.

A Parabola-like Gold Nanobowtie on a Sapphire Substrate as a Nano-Cavity

Plasmonic, metallic nanostructures have attracted much interest for their ability to manipulate light on a subwavelength scale and for their related applications in various fields. In this work, a parabola-like gold nanobowtie (PGNB) on a sapphire substrate was designed as a nano-cavity for confining light waves in a nanoscale gap region. The near-field optical properties of the innovative PGNB structure were studied comprehensively, taking advantage of the time-resolved field calculation based on a finite-difference time-domain algorithm (FDTD). The calculation result showed that the resonance wavelength of the nano-cavity was quite sensitive to the geometry of the PGNB. The values that related to the scattering and absorption properties of the PGNB, such as the scattering cross section, absorption cross section, extinction cross section, scattering ratio, and also the absorption ratio, were strongly dependent on the geometrical parameters which affected the surface area of the nanobowtie. Increased sharpness of the gold tips on the parabola-like nano-wings benefited the concentration of high-density charges with opposite electric properties in the narrow gold tips with limited volume, thus, resulting in a highly enhanced electric field in the nano-cavity under illumination of the light wave. Reduction of the gap size between the two gold nano-tips, namely, the size of the nano-cavity, decreased the distance that the electric potential produced by the highly concentrated charges on the surface of each gold nano-tip had to jump across, therefore, causing a significantly enhanced field in the nano-cavity. Further, alignment of the linearly polarized electric field of the incident light wave with the symmetric axis of the PGNB efficiently enabled the free electrons in the PGNB to concentrate on the surface of the sharp gold tips with a high density, thus, strongly improving the field across the nano-cavity. The research provides a new insight for future design, nanofabrication, and characterization of PGNBs for applications in devices that relate to enhancing photons emission, improving efficiency for energy harvesting, and improving sensitivity for infrared detection.

Scalable Fabrication of Metallic Nanogaps at the Sub-10 nm Level

Metallic nanogaps with metal-metal separations of less than 10 nm have many applications in nanoscale photonics and electronics. However, their fabrication remains a considerable challenge, especially for applications that require patterning of nanoscale features over macroscopic length-scales. Here, some of the most promising techniques for nanogap fabrication are evaluated, covering established technologies such as photolithography, electron-beam lithography (EBL), and focused ion beam (FIB) milling, plus a number of newer methods that use novel electrochemical and mechanical means to effect the patterning. The physical principles behind each method are reviewed and their strengths and limitations for nanogap patterning in terms of resolution, fidelity, speed, ease of implementation, versatility, and scalability to large substrate sizes are discussed.

Metallic Plasmonic Array Structures: Principles, Fabrications, Properties, and Applications

The vast development of nanofabrication has spurred recent progress for the manipulation of light down to a region much smaller than the wavelength. Metallic plasmonic array structures are demonstrated to be the most powerful platform to realize controllable light-matter interactions and have found wide applications due to their rich and tunable optical performance through the morphology and parameter engineering. Here, various light-management mechanisms that may exist on metallic plasmonic array structures are described. Then, the typical techniques for fabrication of metallic plasmonic arrays are summarized. Next, some recent applications of plasmonic arrays are reviewed, including plasmonic sensing, surface-enhanced spectroscopies, plasmonic nanolasing, and perfect light absorption. Lastly, the existing challenges and perspectives for metallic plasmonic arrays are discussed. The aim is to provide guidance for future development of metallic plasmonic array structures.