Synthesis and defect engineering of molybdenum oxides and their SERS applications

Interfacial Bonding Induced Charge Transfer in Two-Dimensional Amorphous MoO3-x/Graphdiyne Oxide Non-Van der Waals Heterostructures for Dominant SERS Enhancement

Two-dimensional semiconductor-based nanomaterials have shown to be an effective substrate for Surface-enhanced Raman Scattering (SERS) spectroscopy. However, the enhancement factor (EF) tends to be relatively weak compared to that of noble metals and does not allow for trace detection of molecules. In this work, we report the successful preparation of two-dimensional (2D) amorphous non-van der Waals heterostructures MoO3-x/GDYO nanomaterials using supercritical CO2. Due to the synergistic effect of the localized surface plasmon resonance (LSPR) effect and the charge transfer effect, it exhibits excellent SERS performance in the detection of methylene blue (MB) molecules, with a detection limit as low as 10-14 M while the enhancement factor (EF) can reach an impressive 2.55×1011. More importantly, the chemical bond bridging at the MoO3-x/GDYO heterostructures interface can accelerate the electron transfer between the interfaces, and the large number of defective surface structures on the heterostructures surface facilitates the chemisorption of MB molecules. And the charge recombination lifetime can be proved by a ~1.7-fold increase during their interfacial electron-transfer process for MoO3-x/GDYO@MB mixture, achieving highly sensitive SERS detection.

A WOx/MoOx hybrid oxide based SERS FET and investigation on its tunable SERS performance

Active control of the surface-enhanced Raman scattering (SERS) enhancement shows great potential for realizing smart detection of different molecules. However, conventional methods usually involve time-consuming structural design or a sophisticated fabrication process. Herein, we reported an electrically tunable field effect transistor (FET) comprising a WOx/MoOx hybrid as the SERS active layer. In the experiment, WOx/MoOx hybrids were first prepared by mixing different molar ratios of WOx and MoOx oxides. Then, R6G molecules were used as Raman reporters, showing that the intensity of the SERS signal observed on the most optimal hybrids (molar ratio = 1 : 3) could be increased by two times as high as that observed on a single WOx or MoOx based substrate, which was ascribed to enhanced charge transfer efficiency by the constructed nano-heterojunction between the WOx and MoOx oxides. Thereafter, a back-gate FET was fabricated on a SiO2/Si substrate, and the most optimal WOx/MoOx hybrid was deposited as the gate channel and the SERS active layer. After that, a series of gate biases (from -15 V to 15 V) were implemented to actively tune the SERS performance of the FET. It is evident that the SERS EF can be further tuned from 2.39 × 107 (-15 V) to 6.55 × 107 (+10 V), which is ∼7.4/4.1 times higher than that observed on the pure WOx device (8.81 × 106) or pure MoOx (1.61 × 107) device, respectively. Finally, the mechanism behind the electrical tuning strategy was investigated. It is revealed that a positive voltage would bend the conduction band down, which increased the electron density near the Fermi level. Consequently, it triggered the resonance charge transfer and significantly improved the SERS performance. In contrast, a negative gate voltage attracted the holes to the Fermi level, which deferred the charge transfer process, and caused the reduction of the SERS enhancement.

Fe and Cu Intercalations Enhance SERS of MoO3 through Different Mechanistic Pathways

Surface Enhanced Raman spectroscopy (SERS) is a molecular-specific analytical technique with various applications. Although electromagnetic (EM) and chemical (CM) mechanisms have been proposed to be the main origins of SERS, exploring highly sensitive SERS substrates with well-defined mechanistic pathways remains challenging. Since surface and electronic structures of substrates were crucial for SERS activity, zero-valent transition metals (Fe and Cu) were intercalated into MoO3 to modulate its surface and electronic structures, leading to unexceptional high enhancement factors (1.0×108 and 1.1×1010 for Fe-MoO3 and Cu-MoO3 , respectively) with decent reproducibility and stability. Interestingly, different mechanistic pathways (CM and EM) were proposed for Fe-MoO3 and Cu-MoO3 according to mechanistic investigations. The different mechanisms of Fe-MoO3 and Cu-MoO3 were rationalized by the electronic structures of the intercalated Fe(0) and Cu(0), which modulates the surface and electronic structures of Fe-MoO3 and Cu-MoO3 to differentiate their SERS mechanisms.

Multi-layer core-shell metal oxide/nitride/carbon and its high-rate electroreduction of nitrate to ammonia

The electroreduction of nitrate to ammonia is both an alternative strategy to industrial Haber-Bosch ammonia synthesis and a prospective idea for changing waste (nitrate pollution of groundwater around the world) into valuable chemicals, but still hindered by its in-process strongly competitive hydrogen evolution reaction (HER), low ammonia conversion efficiency, and the absence of stability and sustainability. Considering the unique electronic structure of anti-perovskite structured Fe4N, a tandem disproportionation reaction and nitridation-carbonation route for building a multi-layer core-shell oxide/nitride/C catalyst, such as MoO2/Fe4N/C, is designed and executed, in which abundant Fe-N active sites and rich phase interfaces are in situ formed for both suppressing HER and fast transport of electrons and reaction intermediates. As a result, the sample's NO3RR conversion displays a very high NH3 yield rate of up to 11.10 molNH3 gcat.-1 h-1 (1.67 mmol cm-2 h-1) with a superior 99.3% faradaic efficiency and the highest half-cell energy efficiency of 30%, surpassing that of most previous reports. In addition, it is proved that the NO3RR assisted by the MoO2/Fe4N/C electrocatalyst can be carried out in 0.50-1.00 M KNO3 electrolyte at a pH value of 6-14 for a long time. These results guide the rational design of highly active, selective, and durable electrocatalysts based on anti-perovskite Fe4N for the NO3RR.

Insights into the Semiconductor SERS Activity: The Impact of the Defect-Induced Energy Band Offset and Electron Lifetime Change

The significant boost in surface-enhanced Raman scattering (SERS) by the chemical enhancement of semiconducting oxides is a pivotal finding. It offers a prospective path toward high uniformity and low-cost SERS substrates. However, a detailed understanding of factors that influence the charge transfer process is still insufficient. Herein, we reveal the important role of defect-induced band offset and electron lifetime change in SERS evolution observed in a MoO3 oxide semiconductor. By modulating the density of oxygen vacancy defects using ultraviolet (UV) light irradiation, SERS is found to be improved with irradiation time in the first place, but such improvement later deteriorates for prolonged irradiation even if more defects are generated. Insights into the observed SERS evolution are provided by ultraviolet photoelectron spectroscopy and femtosecond time-resolved transient absorption spectroscopy measurements. Results reveal that (1) a suitable offset between the energy band of the substrate and the orbitals of molecules is facilitated by a certain defect density and (2) defect states with relatively long electron lifetime are essential to achieve optimal SERS performance.

Microfluidic SERS devices: brightening the future of bioanalysis

A new avenue has opened up for applications of surface-enhanced Raman spectroscopy (SERS) in the biomedical field, mainly due to the striking advantages offered by SERS tags. SERS tags provide indirect identification of analytes with rich and highly specific spectral fingerprint information, high sensitivity, and outstanding multiplexing potential, making them very useful in in vitro and in vivo assays. The recent and innovative advances in nanomaterial science, novel Raman reporters, and emerging bioconjugation protocols have helped develop ultra-bright SERS tags as powerful tools for multiplex SERS-based detection and diagnosis applications. Nevertheless, to translate SERS platforms to real-world problems, some challenges, especially for clinical applications, must be addressed. This review presents the current understanding of the factors influencing the quality of SERS tags and the strategies commonly employed to improve not only spectral quality but the specificity and reproducibility of the interaction of the analyte with the target ligand. It further explores some of the most common approaches which have emerged for coupling SERS with microfluidic technologies, for biomedical applications. The importance of understanding microfluidic production and characterisation to yield excellent device quality while ensuring high throughput production are emphasised and explored, after which, the challenges and approaches developed to fulfil the potential that SERS-based microfluidics have to offer are described.

Emerging SERS biosensors for the analysis of cells and extracellular vesicles

Cells and their derived extracellular vesicles (EVs) or exosomes contain unique molecular signatures that could be used as biomarkers for the detection of severe diseases such as cancer, as well as monitoring the treatment response. Revealing these molecular signatures requires developing non-invasive ultrasensitive tools to enable single molecule/cell-level detection using a small volume of sample with low signal-to-noise ratio background and multiplex capability. Surface-enhanced Raman scattering (SERS) can address the current limitations in studying cells and EVs through two main mechanisms: plasmon-enhanced electric field (the so-called electromagnetic mechanism (EM)), and chemical mechanism (CM). In this review, we first highlight these two SERS mechanisms and then discuss the nanomaterials that have been used to develop SERS biosensors based on each of the aforementioned mechanisms as well as the combination of these two mechanisms in order to take advantage of the synergic effect between electromagnetic enhancement and chemical enhancement. Then, we review the recent advances in designing label-aided and label-free SERS biosensors in both colloidal and planar systems to investigate the surface biomarkers on cancer cells and their derived EVs. Finally, we discuss perspectives of emerging SERS biosensors in future biomedical applications. We believe this review article will thus appeal to researchers in the field of nanobiotechnology including material sciences, biosensors, and biomedical fields.

Flexible surface-enhanced Raman scatting substrates: recent advances in their principles, design strategies, diversified material selections and applications

Surface-enhanced Raman scattering (SERS) is widely used as a powerful analytical technology in cutting-edge areas such as food safety, biology, chemistry, and medical diagnosis, providing ultra-fast, ultra-sensitive, nondestructive characterization and achieving ultra-high detection sensitivity even down to the single-molecule level. Development of Raman spectroscopy is strongly dependent on high-performance SERS substrates, which have long evolved from the early days of rough metal electrodes to periodic nanopatterned arrays building on solid supporting substrates. For rigid SERS substrates, however, their applications are restricted by sophisticated pretreatments for detecting solid samples with non-planar surfaces. It is therefore essential to reassert the principles in constructing flexible SERS substrates. Herein, we comprehensively review the state-of-the-art in understanding, preparing and using flexible SERS. The basic mechanisms behind the flexible SERS are briefly outlined, typical design strategies are highlighted and diversified selection of materials in preparing flexible SERS substrates are reviewed. Then the recent achievements of various interdisciplinary applications based on flexible SERS substrates are summarized. Finally, the challenges and perspectives for future evolution of flexible SERS and their applications are demonstrated. We propose new research directions focused on stimulating the real potential of SERS as an advanced analytical technique for commercialization.

Semiconductor-based surface enhanced Raman scattering (SERS): from active materials to performance improvement

Surface enhanced Raman scattering (SERS) is a powerful spectral analysis technique and has exhibited remarkable application prospects in various fields. The design and fabrication of high-performance SERS substrates is key to promoting the development of SERS technology. Apart from noble metal substrates, non-metal substrates based on semiconductor materials have received increasing attention in recent years owing to their unique physical, chemical, and optical properties. However, compared with noble metal substrates, most semiconductor substrates show weak Raman enhancement ability. Therefore, exploring effective strategies to improve the SERS sensitivity is an urgent task. Numerous reviews have outlined the research progress of semiconductor SERS substrates, which mainly focused on summarizing the material category of semiconductor substrates. However, reviews that systematically summarize the strategies for improving the SERS performance of semiconductor substrates are lacking. In this review, we comprehensively discuss the research on semiconductor SERS from the aspects of mechanism, materials, and modification. Firstly, the Raman enhancement mechanism of semiconductor substrates and the SERS-active materials are discussed. Then, we summarize several effective approaches to boost the SERS performance of semiconductor substrates. In conclusion, we propose some prospects for this field.

Charge-Transfer Resonance and Surface Defect-Dominated WO3 Hollow Microspheres as SERS Substrates for the miRNA 155 Assay

Chemical enhancement with charge transfer (CT) between the adsorbed Raman molecule and the semiconductor mainly contributed to semiconductor surface-enhanced Raman scattering (SERS). In this work, a three-dimensional (3D) WO₃ hollow microsphere is first developed as a SERS-active substrate. This 3D WO₃ has a smaller band gap and rich surface defects compared with flake WO₃. Interestingly, these properties in the WO₃ hollow microspheres lead to an increase in charge transfer, which causes a strong CT interaction between the substrate-Raman molecule interfaces, resulting in a large SERS enhancement. The 3D WO₃ showed an excellent SERS performance with an enhancement factor (EF) of 1.6 × 10⁶. Finally, a SERS biosensor is constructed based on the above-mentioned semiconductor materials, which can be used for the sensitive detection of miRNA 155 with a limit of detection (LOD) of 0.18 fM by employing a catalytic hairpin assembly (CHA) strategy. This work provides important guidance for semiconductor topography design to improve the SERS performance, supplying a new strategy for biomolecular analysis and disease diagnosis.

3D hierarchically porous magnetic molybdenum trioxide@gold nanospheres as a nanogap-enhanced Raman scattering biosensor for SARS-CoV-2

The global pandemic of COVID-19 is an example of how quickly a disease-causing virus can take root and threaten our civilization. Nowadays, ultrasensitive and rapid detection of contagious pathogens is in high demand. Here, we present a novel hierarchically porous 3-dimensional magnetic molybdenum trioxide-polydopamine-gold functionalized nanosphere (3D mag-MoO3-PDA@Au NS) composed of plasmonic, semiconductor, and magnetic nanoparticles as a multifunctional nanosculptured hybrid. Based on the synthesized 3D mag-MoO3-PDA@Au NS, a universal "plug and play" biosensor for pathogens is proposed. Specifically, a magnetically-induced nanogap-enhanced Raman scattering (MINERS) detection platform was developed using the 3D nanostructure. Through a magnetic actuation process, the MINERS system overcomes Raman signal stability and reproducibility challenges for the ultrasensitive detection of SARS-CoV-2 spike protein over a wide dynamic range up to a detection limit of 10-15 g mL-1. The proposed MINERS platform will facilitate the broader use of Raman spectroscopy as a powerful analytical detection tool in diverse fields.

Constructing the Mo2C@MoOx Heterostructure for Improved SERS Application

Surface-enhanced Raman scattering (SERS) is a non-destructive spectra analysis technique. It has the virtues of high detectivity and sensitivity, and has been extensively studied for low-trace molecule detection. Presently, a non-noble-metal-based SERS substrate with excellent enhancement capabilities and environmental stability is available for performing advanced biomolecule detection. Herein, a type of molybdenum carbide/molybdenum oxide (Mo₂C@MoO_x) heterostructure is constructed, and attractive SERS performance is achieved through the promotion of the charge transfer. Experimentally, Mo₂C was first prepared by calcinating the ammonium molybdate tetrahydrate and gelatin mixture in an argon atmosphere. Then, the obtained Mo₂C was further annealed in the air to obtain the Mo₂C@MoO_x heterostructure. The SERS performance was evaluated by using a 532 nm laser as an excitation source and a rhodamine 6G (R6G) molecule as the Raman reporter. This process demonstrates that attractive SERS performance with a Raman enhancement factor (EF) of 1.445 × 10⁸ (R6G@10⁻⁸ M) and a limit of detection of 10⁻⁸ M can be achieved. Furthermore, the mechanism of SERS performance improvement with the Mo₂C@MoO_x is also investigated. HRTEM detection and XPS spectra reveal that part of the Mo₂C is oxidized into MoO_x during the air-annealing process, and generates metal–semiconductor mixing energy bands in the heterojunction. Under the Raman laser irradiation, considerable hole–electron pairs are generated in the heterojunction, and then the hot electrons move towards MoO_x and subsequently transfer to the molecules, which ultimately boosts the Raman signal intensity.

High spin Fe3+-related bonding strength and electron transfer for sensitive and stable SERS detection

The SERS performance of trimetallic MIL-101(FeNiTi) and the spin state of Fe3+ is positively correlated. The SERS enhancement mechanism is explored regarding the bonding strength and charge transfer between molecules and MIL-101.

Enhanced charge-transfer induced by conduction band electrons in aluminum-doped zinc oxide/molecule/Ag sandwich structures observed by surface-enhanced Raman spectroscopy

In the semiconductor/molecule/metal system, enhancing the efficiency of the charge-transfer (CT) plays a pivotal role in improving the sensitivity of semiconductor-based surface-enhanced Raman scattering (SERS). In this work, use of SERS for detection of an enhanced CT in a chemically-etched Al-doped ZnO (AZO), 4-mercaptopyridine (MPy) molecule, and Ag nanoparticles (NPs) (AZO/MPy/Ag) sandwich structure is reported. A series of CT routes are proposed in the energy level diagram of AZO/MPy/Ag assemblies under the excitation line at 633 nm. Very interestingly, for the first of its kind, a significant CT route from the conduction band (CB) of AZO to the lowest unoccupied molecular orbital (LUMO) of MPy molecule is detected. This route can remarkably improve the degree of CT in the AZO/MPy/Ag system by about 48% compared with that of the ZnO/MPy/Ag system. Furthermore, the uniquely enhanced CT route is also further confirmed by alternative probe molecules like p-aminothiophenol (PATP) and 4-mercaptobenzoic acid (MBA). The discovery of this extra CT route will inevitably play an irreplaceable role in SERS enhancement through its participating in the CT enhancement mechanism.

Molybdenum Oxide/Tungsten Oxide Nano-heterojunction with Improved Surface-Enhanced Raman Scattering Performance

By virtue of their high uniformity and stability, metal oxide-based surface-enhanced Raman spectroscopy (SERS) substrates have attracted enormous attention for molecular trace detection. However, strategies for further enhancing the SERS sensitivity are still desired. Herein, MoO_x/WO_x nano-heterojunctions are constructed by mixing MoO_x and WO_x together (MoO_x/WO_x hybrid) with diverse weight ratios. Using a 532 nm laser as the excitation source and R6G as the Raman reporter, it is shown that the Raman signal intensity (for the peak @ 1360 cm^-1) obtained on the optimal MoO_x/WO_x hybrid (MoO_x/WO_x = 1:1/3) is twice that observed on a pure MoO_x or WO_x substrate. Moreover, a limit of detection of 10^-8 M and an enhancement factor of 10⁸ are achieved. In the SERS enhancement mechanism investigation, it is revealed that MoO_x and WO_x form a staggered band structure. During the SERS measurement, electron-hole pairs are generated in the nano-heterojunction using the incident laser. They are then separated by the built-in potential with the electrons moving toward WO_x. The accumulated electrons on WO_x are further transferred to the R6G molecules through the coupling of orbitals. Consequently, the molecular polarizability is amplified, and SERS performance is enhanced. The abovementioned explanation is supported by the evidence that the contribution of the chemical enhancement mechanism in the optimal MoO_x/WO_x hybrid substrate is about 2.5 times or 5.9 times that in the pure WO_x or MoO_x substrate.

Molybdenum Trioxide Quantum Dot-Encapsulated Nanogels for Virus Detection by Surface-Enhanced Raman Scattering on a 2D Substrate

The use of nanogels (NGs) to modulate surface-enhanced Raman scattering (SERS) activities is introduced as an innovative strategy to address certain critical issues with SERS-based immunoassays. This includes the chemical deformation of SERS nanotags, as well as their nonspecific interactions and effective "hotspots" formation. Herein, the polymeric cocoon and stimuli-responsive properties of NGs were used to encapsulate SERS nanotags containing plasmonic molybdenum trioxide quantum dots (MoO₃-QDs). The pH-controlled release of the encapsulated nanotags and their subsequent localization by maleimide-functionalized magnetic nanoparticles facilitated the creation of "hotspots" regions with catalyzed SERS activities. This approach resulted in developing a biosensing platform for the ultrasensitive immunoassays of hepatitis E virus (HEV) or norovirus (NoV). The immunoassays were optimized using the corresponding virus-like particles to attain limits of detection of 6.5 and 8.2 fg/mL for HEV-LPs and NoV-LPs, respectively. The SERS-based technique achieved a signal enhancement factor of up to ∼10⁸ due to the combined electromagnetic and chemical mechanisms of the employed dual-SERS substrate of MoO₃-QDs/2D hexagonal boron nitride nanosheets. The highlight and validation of the developed SERS-based immunoassays was the detection of NoV in infected patients' fecal specimen and clinical HEV G7 subtype. Importantly, this system can be used to maintain the stability of SERS nanotags and improve their reliability in immunoassays.