Investigation of the Conditions for the Synthesis of Poly(3,4-ethylenedioxythiophene) ATRP Macroinitiator

One of the most widely used conductive polymers in the growing conductive polymer industry is poly(3,4-ethylenedioxythiophene) (PEDOT), whose main advantages are good thermal and chemical stability, a conjugated backbone, and ease of functionalization. The main drawback of PEDOT for use as wearable electronics is the lack of stretchable and self-healing properties. This can be overcome by grafting PEDOT with flexible side branches. As pure PEDOT is highly stable and grafting would not be possible, a new bromine-functionalized thiophene derivative, 2-(tiophen-3-yl) ethyl 2-bromo-2-methylpropanoate (ThBr), was synthesized and copolymerized with EDOT for the synthesis of a poly(EDOT-co-ThBr) ATRP macroinitiator. After the synthesis of the macroinitiator, flexible polymers could be introduced as side branches by atom-transfer radical polymerization (ATRP) to modify mechanical properties. Before this last synthesis step, the conditions for the synthesis of the ATRP macroinitiator should be investigated, as only functionalized units can function as grafting sites. In this study, nine new copolymers with different monomer ratios were synthesized to investigate the reactivity of each monomer. The ratios used in the different syntheses were ThBr:EDOT = 1:0.2, 1:0.4, 1:0.6, 1:0.8, 1:1, 0.8:1, 0.6:1, 0.4:1, and 0.2:1. In order to determine the effect of reaction time on the final properties of the polymer, macroinitiator synthesis at a 1:1 ratio was carried out at different time periods: 8 h, 16 h, 24 h, and 48 h. The obtained products were characterized by different techniques, and it was found that polymerizations longer than 24 h yielded practically insoluble macroinitiators, thus limiting its further application. Reactivity ratios of both monomers were found to be similar and close to 1, making the copolymerization reaction symmetrical and the obtained macroinitiators almost random copolymers.

Applying an Oleophobic/Hydrophobic Fluorinated Polymer Monolayer Coating from Aqueous Solutions

Despite major advancements in the fabrication of low-surface-energy surfaces, the environmental consequences of their fabrication can be a serious issue, particularly in an industrial context. This is especially the case for fluorine-based coatings, which often require fluorinated solvents for their processing and applications. These solvents are not only detrimental to the ozone layer but also represent a potential workplace hazard because they tend to bioaccumulate. We describe the design, synthesis, and characterization of a new fluorinated-polymer coating that can be simply applied to surfaces from an aqueous environment using a dip-coating technique. This was made possible by copolymerizing three different methacrylate monomers, each serving a specific function. Namely, fluorinated methacrylate providing oleo/hydrophobicity, photocleavable polyethylene glycol (PEG) methacrylate promoting water solubility of the copolymer, and thioether-based methacrylate serving as an anchoring unit to a number of different substrates. This copolymer is initially grafted to the surface as a monolayer from an aqueous solvent, after which the system is treated with ultraviolet (UV) light, cleaving away the protecting PEG moieties to yield an oleo/hydrophobic surface.

Fabrication of 2D Block Copolymer Brushes via a Polymer-Single-Crystal-Assisted-Grafting-to Method

Block copolymer brushes are of great interest due to their rich phase behavior and value-added properties compared to homopolymer brushes. Traditional synthesis involves grafting-to and grafting-from methods. In this work, a recently developed "polymer-single-crystal-assisted-grafting-to" method is applied for the preparation of block copolymer brushes on flat glass surfaces. Triblock copolymer poly(ethylene oxide)-b-poly(l-lactide)-b-poly(3-(triethoxysilyl)propyl methacrylate) (PEO-b-PLLA-b-PTESPMA) is synthesized with PLLA as the brush morphology-directing component and PTESPMA as the anchoring block. PEO-b-PLLA block copolymer brushes are obtained by chemical grafting of the triblock copolymer single crystals onto a glass surface. The tethering point and overall brush pattern are determined by the single crystal morphology. The grafting density is calculated to be ≈0.36 nm^-2 from the atomic force microscopy results and is consistent with the theoretic calculation based on the PLLA crystalline lattice. This work provides a new strategy to synthesize well-defined block copolymer brushes.