Laser-induced crystallization of anodic TiO2 nanotube layers

Scanning with Laser Beam over the TiO2 Nanotubes Covered with Thin Chromium Layers towards the Activation of the Material under the Visible Light

This work presents pulsed UV laser treatment (355 nm, 2 Hz) of TiO₂ nanotubes decorated with chromium oxides. The modification was performed in a system equipped with a beam homogenizer, and during the irradiation, the samples were mounted onto the moving motorized table. In such a system, both precisely selected areas and any large area of the sample can be modified. Photoelectrochemical tests revealed photoresponse of laser-treated samples up to 1.37- and 18-fold under the illumination with ultraviolet-visible and visible light, respectively, in comparison to bare titania. Optimal beam energy fluence regarding sample photoresponse has been established. Scanning electron microscopy images, X-ray diffraction patterns, along with Raman and X-ray photoelectron spectra, suggest that the enhanced photoresponse results from changes solely induced in the layer of chromium oxides. It is believed that the results of the present work will contribute to a wider interest in laser modification of semiconductors exhibiting improved photoelectrochemical activity.

The Impact of Side-Selective Laser Tailoring of Titania Nanotubes on Changes in Photoelectrocatalytic Activity

Over the last few decades, titanium(IV) oxide-based materials have gained particular attention due to their stability, corrosion resistance, photocatalytic activity under UV light, and possibilities for modification. Among various structures, TiO₂ nanotubes (NTs) grown on Ti foil or glass substrates and obtained through a simple anodization process are widely used as photocatalysts or photoanodes. During the anodization process, the geometry of the nanotubes (length, distribution, diameter, wall thickness, etc.) is easily controlled, though the obtained samples are amorphous. Heat treatment is required to transform the amorphous material into crystalline material. However, instead of time- and cost-consuming furnace treatment, fast and precise laser annealing is applied as a promising alternative. Nonetheless, laser treatment can result in geometry changes of TiO₂ NTs, consequently altering, their electrochemical activity. Moreover, modification of the TiO₂ NTs surfaces with transition metals and further laser treatment can result in materials with unique photoelectrochemical properties. In this regard, we gathered the latest achievements in the field of laser-treated titania for this review paper. We mainly focused on single structural and morphological changes resulting from pulsed laser annealing and their influence on the electrochemical properties of titania. Finally, the theoretical basis for and combination of laser- and metal-modifications and their impact on the resulting possibilities for electrochemical water splitting are also discussed.

Influence of laser and alkali treatment on an Ag/TiO2nanotube based dopamine sensor

Herein, TiO₂nanotubes (T-NTs) arrays were subjected to two types of treatment followed by a simple metal deposition technique to significantly enhance the performances of T-NTs based electrochemical sensing of dopamine. The first type of treatment was done by soaking T-NTs in sodium hydroxide solution for an optimal time to enhance the conductivity and charge carrier density. The second type of treatment employed was laser irradiation, which induces crystallinity disorder and forms rutile TiO₂, promoting active analyte adsorption sites. Afterward, silver (Ag) was electro-deposited on the T-NTs as a dopamine sensing catalyst to form T-NTs/Ag nanohybrids. The dual-treated T-NTs based sensor showed 3-fold enhancement in sensitivity (from 8.2μA mM^-1cm^-2to 32μA mM^-1cm^-2), reduced charge transfer resistance (from 38 × 10^-6Ω to 0.7 × 10^-6Ω), above 2 order higher donor charge density (from 3.58 × 10¹⁸cm^-3to 1.41 × 10²¹cm^-3), and reduced limit of detection (from 32.3μM to 2.8μM) in comparison to plain T-NTs based sensor. In addition, the sensitivity reported here is significantly higher than most of the previously reported TiO₂based dopamine sensors. Perspective-wise, the dual treatment approach is a promising technique and is highly desirable for enhancing the performances of T-NTs and other nanomaterial based electrochemical sensors.

Formation of the hollow nanopillar arrays through the laser-induced transformation of TiO2 nanotubes

In the following article, we present a simple, two-step method of creating spaced, hollow nanopillars, from the titania nanotube arrays via pulsed laser-treatment. Due to the high ordering of the structure, the prepared material exhibits photonic properties, which has been shown to increase the overall photoefficiency. The optical and morphological changes in the titania nanotubes after pulsed laser-treatment with 532, 355, and 266 nm wavelengths in the 10-50 mJ/cm2 fluence range are studied. The investigation reveals, that by using appropriate wavelength and energy, the number of surface defects, geometrical features, or both can be tailored.