Near-Infrared Remotely Controllable Shape Memory Biodegradable Occluder Based on Poly(l-lactide-co-ε-caprolactone)/Gold Nanorod Composite

Biodegradable occluders, which can efficiently eliminate the complications caused by permanent foreign implants, are considered to be the next-generation devices for the interventional treatment of congenital heart disease. However, the controllability of the deployment process of degradable occluders remains a challenge. In this work, a near-infrared (NIR) remotely controllable biodegradable occluder is explored by integrating poly(l-lactide-co-ε-caprolactone) (PLCL) with poly(ethylene glycol)-modified gold nanorods (GNR/PEG). The caprolactone structural units can effectively increase the toughness of poly(l-lactide) and reduce the shape-memory transition temperature of the occluder to a more tissue-friendly temperature. Gold nanorods endow the PLCL-GNR/PEG composite with an excellent photothermal effect. The obtained occluder can be easily loaded into a catheter for transport and spatiotemporally expanded under irradiation with near-infrared light to block the defect site. Both in vitro and in vivo biological experiments showed that PLCL-GNR/PEG composites have good biocompatibility, and the PEGylated gold nanorods could improve the hemocompatibility of the composites to a certain extent by enhancing their hydrophilicity. As a thermoplastic shape-memory polymer, PLCL-GNR/PEG can be easily processed into various forms and structures for different patients and lesions. Therefore, PLCL-GNR/PEG has the potential to be considered as a competitive biodegradable material not only for occluders but also for other biodegradable implants.

Mussel-inspired polyurethane coating for bio-surface functionalization to enhance substrate adhesion and cell biocompatibility

Considerable implant materials are prone to cause a severe inflammatory reaction due to poor histocompatibility, which leads to various complications and implant failure. Surface coating modification of these implant materials is one of the most important techniques to settle this problem. However, fabricating a coating with both adequate adhesiveness and excellent biocompatibility remains a challenge. Inspired by the adhesion mechanism of mussels, a series of mussel-inspired polyurethanes (PU-LDAs) were synthysized through a step growth polymerization based on hexamethylene diisocyanate as a hard segment, polytetra-methylene-ether-glycol as a soft segment, lysine-dopamine (LDA) and butanediol as chain extenders with different mole ratios.The coatings of PU-LDAs were applied to various substrates, such as stainless steel, glass and PP using a facile one-step coating process. The introduction of 3,4-dihydroxyphenylalanine (DOPA) groups can greatly improve the adhesion ability of the coatings to the substrates demonstrated by a 180° peel test. The peel strength of the PU-LDA100 coating containing high LDA content was 76.3, 48.5 and 67.5 N/m, which was 106.2%, 246.4% and 192.2% higher than that of the PU-LDA00 coating without LDA on the surface of stainless steel, glass and PP, respectively. Meanwhile, this PU coating has a lower immune inflammatory response which provides a universal method for surface modification of implant materials. Moreover, the DOPA groups in PU-LDAs could combine with the amino and thiol groups on cell membrane surface, leading to the improvement of cell adhesion and growth. Therefore, it has great potential application in the field of biomedical implant materials for the clinic.

Digital Light 3D Printed Bioresorbable and NIR-Responsive Devices with Photothermal and Shape-Memory Functions

Digital light processing (DLP) 3D printing is a promising technique for the rapid manufacturing of customized medical devices with high precision. To be successfully translated to a clinical setting, challenges in the development of suitable photopolymerizable materials have yet to be overcome. Besides biocompatibility, it is often desirable for the printed devices to be biodegradable, elastic, and with a therapeutic function. Here, a multifunctional DLP printed material system based on the composite of gold nanorods and polyester copolymer is reported. The material demonstrates robust near-infrared (NIR) responsiveness, allowing rapid and stable photothermal effect leading to the time-dependent cell death. NIR light-triggerable shape transformation is demonstrated, resulting in a facilitated insertion and expansion of DLP printed stent ex vivo. The proposed strategy opens a promising avenue for the design of multifunctional therapeutic devices based on nanoparticle-polymer composites.

NIR Photothermal-Responsive Shape Memory Polyurethane with Protein-Inspired Aggregated Chymotrypsin-Sensitive Degradable Domains

Biodegradable shape memory polymers are promising biomaterials for stents used in minimally invasive surgical procedures such as intestinal stents. Herein, a series of biodegradable shape memory polyurethanes (SMPUs) containing a novel phenylalanine-derived chain extender PHP were synthesized. Inspired by the fact that the function of biomacromolecules such as proteins is rich and varied because of the multiple combinations of the amino acid in highly evolved biosystems, we found that the sequence distribution of PHP in SMPU would also have a great influence on the phase structure and degradation behavior, especially the difference of surface morphology caused by degradation. Considering that the transition temperature (T_trans ) of SMPU we obtained is higher than physiological temperature, oxidized carbon black (OCB) with the ability of photothermal conversion was introduced into SMPU, which can not only endow SMPU with near-infrared response shape recovery characteristics, but also enhance phase separation degree and mechanical properties of them. SMPU/OCB composites show excellent shape memory effect and rapid photothermal response, and they can be degraded by chymotrypsin with an adjustable degradation rate. These SMPU/OCB composites show broad potential for application as intestinal stents. This article is protected by copyright. All rights reserved.

Water-Triggered Stiffening of Shape-Memory Polyurethanes Composed of Hard Backbone Dangling PEG Soft Segments

Shape-memory polymers (SMPs) induced by heat or water are commonly used candidates for biomedical applications. Shape recovery inevitably leads to a dramatic decrease of Young's modulus due to the enhanced flexibility of polymer chains at the transition temperature. Herein, the principle of phase-transition-induced stiffening of shape-memory metallic alloys (SMAs) is introduced to the design of molecular structures for shape-memory polyurethane (SMPUs), featuring all-hard segments composed of main chains that are attached with poly(ethylene glycol) (PEG) dangling side chains. Different from conventional SMPs, they achieve a soft-to-stiff transition when shape recovers. The stiffening process is driven by water-triggered segmental rearrangement due to the incompatibility between the hard segments and the soft PEG segments. Upon hydration, the extent of microphase separation is enhanced and the hard domains are transformed to a more continuous morphology to realize more effective stress transfer. Meanwhile, such segmental rearrangement facilitates the shape-recovery process in the hydrated state despite the final increased glass transition temperature (T_g ). This work represents a novel paradigm of simultaneously integrating balanced mechanics, shape-memory property, and biocompatibility for SMPUs as materials for minimally invasive surgery such as endoluminal stents.

Shape memory polyurethane potentially used for vascular stents with water-induced stiffening and improved hemocompatibility

We designed a shape memory polyurethane potentially used for vascular stents with water-induced stiffening in vivo and improved hemocompatibility.

Tough and biodegradable polyurethane-curcumin composited hydrogel with antioxidant, antibacterial and antitumor properties

The functionalization of tough and biodegradable hydrogels is an important way to broaden their applications in biomedical field. However, most of the hydrophobic functional drugs are difficult to incorporate with the hydrogels. In this work, curcumin (Cur), a hydrophobic functional drug, was chosen to composite with polyurethane (PU) to obtain PU-Cur hydrogels by a direct and simple in-situ copolymerization. The incorporation of curcumin in PU hydrogel increases the crosslink but reduces the hydrophilicity and degradation rate of PU-Cur hydrogels. Thus, it can increase the mechanical strength to a maximum of 6.4±0.8 MPa and initial modulus to a maximum of 3.0±0.4 MPa. More importantly, curcumin incorporated in PU networks is not deactivated. The degradation products of PU-Curs at relatively low concentrations (2.5 mg/mL) can scavenge free radicals very efficiently (maximum over 90%), which exhibits strong antioxidant properties to improve wound healing. Moreover, based on the photochemical activity of curcumin, notable inhibition effects of the degradation products of PU-Curs against bacteria (maximum over 80%) and cancer cells are demonstrated with blue light treatment as a photodynamic therapy (PDT). Therefore, the beneficial effects of curcumin are retained in PU-Cur hydrogels, suggesting potential use as wound dressings or tumor isolation membranes. This work proposes a promising strategy to combine hydrophobic functional drugs with hydrophilic hydrogels for applications in a wide range of biomaterials.

Synthesis and characterization of PLGA-PEG-PLGA based thermosensitive polyurethane micelles for potential drug delivery

Polyurethane nanomicelle is a promising functional drug delivery system. In this work, the polyurethane (P3-PU) was synthesized from PLGA₁₂₀₀-PEG₁₄₅₀-PLGA₁₂₀₀ (P3, a thermosensitive and biodegradable triblock copolymer) and L-lysine ester diisocyanate (LDI). Then, reactive benzaldehyde was further imported to terminate P3-PU to obtain benzaldehyde modified polyurethane (P3-PUDA). The micelles, temperature-sensitive P3-PU nanomicelle and P3-PUDA nanomicelle, were systematically investigated, including the size, stability, temperature sensitivity, drug loading and release behavior, cytotoxic on human hepatocytes (L02), and inhibitory effect on human hepatocellular carcinoma cells (HepG2). The results show the thermosensitive behavior of the micelles can be adjusted by the terminal group. The polyurethane micelles with a uniform size between 20 nm and 30 nm showed excellent stability and good biocompatibility to L02 cells. Besides, in vitro experiments showed that Dox-loaded P3-PUDA micelles exhibited faster and higher release rate at 37 °C and better inhibitory effect on HepG2 than the Dox-loaded P3-PU micelles. Moreover, the achieved benzaldehyde modified polyurethanes also provides various possibilities to adjust further to enlarge its applications. Therefore, the polyurethane micelles will have great potential in the field of drug carriers.