Heterointerface optimization in a covalent organic framework-on-MXene for high-performance capacitive deionization of oxygenated saline water

Recent advances of copolymer for water treatment

Increasing water pollution due to anthropogenic activities prompts the quest for an effective water treatment method. Polymeric materials have gained attention as adsorbents for water purification. Membranes are majorly made from homopolymeric materials. However, recent studies have focused on using copolymeric materials for improved performance. In this review, the basics of copolymerization including various types of copolymers, synthetic approaches, and their applications in various water pollutants removal are discussed in detail. Advances in water treatment technology using copolymeric materials as adsorbent/membranes in the last 4 years are covered with insights into the future outlook and areas of improvement in terms of copolymer composites for water treatment. Studies from the literature did not only reveal effectiveness of copolymer as a flocculant/antifouling materials and in removal of selective toxic metals, oil, and microbes but also demonstrated recyclability of the copolymer sorbents/membrane. Full exploration of unique copolymer textural and structural properties could lead to great advancement in water treatment process. PRACTITIONER POINTS: The copolymer types and synthetic methods are discussed. Application of copolymer as adsorbent/membranes for water treatment is presented. Recent advances show good pollutants removal for toxic metals, oil, and organics. Copolymer composites have great potential as adsorbent/membranes for future use in water treatment processes.

Enhanced phosphorus electrosorption using Fe, N-co-doped porous electrode via capacitive deionization

Excessive phosphorus discharge causes water eutrophication and disturbs the homeostasis of aquatic ecosystems. Capacitive deionization (CDI) has been proven to be a more energy-efficient and environmentally friendly technology for removing phosphorus. Raw carbon (Raw C) electrodes are widely used in CDI. However, the phosphorus removal capacity of most unmodified Raw C still needs to be enhanced. Therefore, the Fe, N-co-doped carbon prepared in this study was expected to further improve the phosphorus removal performance. Herein, the optimal electrode with 5% Fe (FeNC) had an approximately 2.7 times higher adsorption capacity than Raw C. At a low concentration (5 mg P/L), FeNC exhibited a high maximum removal capacity of 4.28 mg P/g. Under reversed voltage, the phosphorus was easily desorbed by deionized water. Ion competition studies showed that coexisting ions adversely affected phosphorus adsorption onto FeNC in the order SO42- > NO3- > Cl-. Furthermore, the energy consumption of FeNC was calculated to be as low as 0.0069 kWh/g P and 0.023 kWh/m3 water under 1.2 V. More importantly, phosphorus removal by FeNC during CDI was demonstrated in simulated natural water from the Jinjiang River (Chengdu, China). This study indicated that FeNC is expected to be a potential electrode for CDI dephosphorization.

Heterointerface regulation of covalent organic framework-anchored graphene via a solvent-free strategy for high-performance supercapacitor and hybrid capacitive deionization electrodes

Covalent organic frameworks (COFs) with customizable geometry and redox centers are an ideal candidate for supercapacitors and hybrid capacitive deionization (HCDI). However, their poor intrinsic conductivity and micropore-dominated pore structures severely impair their electrochemical performance, and the synthesis process using organic solvents brings serious environmental and cost issues. Herein, a 2D redox-active pyrazine-based COF (BAHC-COF) was anchored on the surface of graphene in a solvent-free strategy for heterointerface regulation. The as-prepared BAHC-COF/graphene (BAHCGO) nanohybrid materials possess high-speed charge transport offered by the graphene carrier and accelerated electrolyte ion migration within the BAHC-COF, allowing ions to effectively occupy ion storage sites inside BAHC. As a result, the BAHCGO//activated carbon asymmetric supercapacitor achieves a high energy output of 61.2 W h kg-1 and a satisfactory long-term cycling life. More importantly, BAHCGO-based HCDI possesses a high salt adsorption capacity (SAC) of 67.5 mg g-1 and excellent long-term desalination/regeneration stability. This work accelerates the application of COF-based materials in the fields of energy storage and water treatment.

Dynamical Janus-Like Behavior Excited by Passive Cold-Heat Modulation in the Earth-Sun/Universe System: Opportunities and Challenges

The utilization of solar-thermal energy and universal cold energy has led to many innovative designs that achieve effective temperature regulation in different application scenarios. Numerous studies on passive solar heating and radiation cooling often operate independently (or actively control the conversion) and lack a cohesive framework for deep connections. This work provides a concise overview of the recent breakthroughs in solar heating and radiation cooling by employing a mechanism material in the application model. Furthermore, the utilization of dynamic Janus-like behavior serves as a novel nexus to elucidate the relationship between solar heating and radiation cooling, allowing for the analysis of dynamic conversion strategies across various applications. Additionally, special discussions are provided to address specific requirements in diverse applications, such as optimizing light transmission for clothing or window glass. Finally, the challenges and opportunities associated with the development of solar heating and radiation cooling applications are underscored, which hold immense potential for substantial carbon emission reduction and environmental preservation. This work aims to ignite interest and lay a solid foundation for researchers to conduct in-depth studies on effective and self-adaptive regulation of cooling and heating.

Integration of capacitive deionization and forward osmosis for high water recovery and ultrapure water production: concept, modelling and performance analysis

Forward Osmosis (FO), a membrane desalination technology and Capacitive Deionization (CDI), an electrically operated desalination technology, are numerically integrated utilizing four different configurations for the high-water recovery rate and ultrapure water production from brackish water resource. To minimize the wastewater rejection, the CDI desorption stream is continuously fed to the FO unit, efficiently recovering the remaining freshwater. To produce ultrapure water, freshwater stream obtained from FO is provided to the CDI cell, which adsorbs the remaining dissolved solute particles. These two configurations serve the purpose of both industrial as well as domestic water supply requirements. Continuing this concept, the formation of the other two configurations allows us to obtain fresh water and ultrapure water simultaneously and up to a 90% freshwater recovery rate for the areas with inadequate supply. The performance parameters to assess the integration are the Water Recovery Rate (WRR) and Specific Energy Consumption (SEC). The first configuration (CDI-FO), proposed for a high freshwater recovery rate, resulted in 79.33% WRR with an SEC of 0.689 kWh / m 3 . While, for the second configuration (FO-CDI), 34.25% water was recovered as 2.87 ppm ultrapure water along with 34.25% freshwater. The third proposed configuration (CDI-FO-CDI) had a WRR of 79.33%, 14.67% of which was recovered as ultrapure water of concentration 2.86 ppm. The fourth configuration (CDI-FO-FO) developed for high water recovery, removed the maximum of water from the feed stream with a WRR of 91.33% and remained energy-efficient, consuming an SEC of 0.908kWh / m 3 .

Inorganic-Organic Nanoarchitectonics: MXene/Covalent Organic Framework Heterostructure for Superior Microextraction

One of the difficulties limiting covalent organic frameworks (COFs) from becoming excellent adsorbents is their stacking/aggregation architectures owing to poor morphology/structure control during the synthesis process. Herein, an inorganic-organic nanoarchitectonics strategy to synthesize the MXene/COF heterostructure (Ti3 C2 Tx /TAPT-TFP) is developed by the assembly of β-ketoenamine-linked COF on the Ti3 C2 Tx MXene nanosheets. The as-prepared Ti3 C2 Tx /TAPT-TFP retains the 2D architecture and high adsorption capacity of MXenes as well as large specific surface area and hierarchical porous structure of COFs. As a proof of concept, the potential of Ti3 C2 Tx /TAPT-TFP for solid-phase microextraction (SPME) of trace organochlorine pesticides (OCPs) is investigated. The Ti3 C2 Tx /TAPT-TFP based SPME method achieves low limits of detection (0.036-0.126 ng g-1 ), wide linearity ranges (0.12-20.0 ng g-1 ), and acceptable repeatabilities for preconcentrating trace OCPs from fruit and vegetable samples. This study offers insights into the potential of constructing COF or MXene-based heterostructures for the microextraction of environmental pollutants.

Solvent-Free Synthesis of Covalent Organic Framework/Graphene Nanohybrids: High-Performance Faradaic Cathodes for Supercapacitors and Hybrid Capacitive Deionization

Covalent organic frameworks (COFs) with flexible periodic skeletons and ordered nanoporous structures have attracted much attention as potential candidate electrode materials for green energy storage and efficient seawater desalination. Further improving the intrinsic electronic conductivity and releasing porosity of COF-based materials is a necessary strategy to improve their electrochemical performance. Herein, the employed graphene as the conductive substrate to in situ grow 2D redox-active COF (TFPDQ-COF) with redox activity under solvent-free conditions to prepare TFPDQ-COF/graphene (TFPDQGO) nanohybrids and explores their application in both supercapacitor and hybrid capacitive deionization (HCDI). By optimizing the hybridization ratio, TFPDQGO exhibits a large specific capacitance of 429.0 F g-1 due to the synergistic effect of the charge transport highway provided by the graphene layers and the abundant redox-active centers contained in the COF skeleton, and the assembled TFPDQGO//activated carbon (AC) asymmetric supercapacitor possesses a high energy output of 59.4 Wh kg-1 at a power density of 950 W kg-1 and good cycling life. Furthermore, the maximum salt adsorption capacity (SAC) of 58.4 mg g-1 and stable regeneration performance is attained for TFPDQGO-based HCDI. This study highlights the new opportunities of COF-based hybrid materials acting as high-performance supercapacitor and HCDI electrode materials.

3D-Printed Liquid Metal-in-Hydrogel Solar Evaporator: Merging Spectrum-Manipulated Micro-Nano Architecture and Surface Engineering for Solar Desalination

Solar desalination driven by interfacial heating is considered a promising technique to alleviate the freshwater shortage crisis. However, its further extension and application are confined by factors such as highlighted salt accumulation, inferior energy efficiency, and poor durability. Herein, a microsized eutectic gallium-indium (EGaIn) core-shell nanodroplet (denoted as LMTE) with photo-cross-linking and photothermal traits, stabilized by allyl glycidyl ether (AGE)-grafting tannic acid (TA), is explored as the solar absorber for broadband light absorbing and localized micro-nano heat channeling. The LMTE nanodroplets are formulated directly with highly hydrated polymers and photosensitive species to successfully develop a water-based photothermal ink suitable for digital light processing (DLP) 3D printing. As a demonstration, the LMTE composite hydrogel-forged milli-conical needle arrays with metal-phenolic network (MPN)-engineered wettability and photothermal enhancement can be printed by the digital light processing (DLP) technique and designed rationally via a bottom-up strategy. The 3D-printing hydrogel evaporator is composed of spectrum-tailored EGaIn nanodroplets for efficient photon harvesting and MPN-coated milli-cone arrays for water supplying with micro-nano channeling, which function cooperatively to bestow the 3D solar evaporator with superior solar-powered water evaporation (2.96 kg m-2 h-1, 96.93% energy efficiency) and excellent solar desalination (salt cycle and site-specific salt crystallization). Furthermore, a robust steam generating/collecting system of the 3D solar evaporator is demonstrated, providing valuable guidance for building a water-energy-agriculture nexus.

A preliminary attempt at capacitive deionization with PVA/PSS gel coating as an alternative to ion exchange membrane

PVA/PSS composite gel membrane electrode for membrane capacitive deionization (MCDI) was fabricated and characterised in the present study. The composite electrode with ion exchange surface is prepared by coating glutaraldehyde cross-linked polyvinyl alcohol (PVA) composite hydrogel, with Poly (Sodium 4-Styrenesulfonate) (PSS) added into the network, on the surface of activated carbon (AC) electrode. The feasibility of the gel membrane is analyzed by rheological, swelling rates and ion exchange capacity tests. Then electrochemical test and desalination test are used to study the performance of the MCDI electrode. The results show that coating of composite hydrogel layer improved the hydrophilicity, specific capacitance and lower interfacial electron transfer resistance of the electrode. Finally, we assemble the asymmetrical CDI cell with PVA/PSS composite gel electrode and AC electrode. Compared with the AC electrode, the salt adsorption capacity of PVA6-PSS15 can reach 18.9 mg g-1 and stable charge efficiency at 73.0% at operating voltage of 1.2 V. The decrease in specific capacitance of PVA6-PSS15 after 50 cycles is 1.33%, indicating that the electrode has a good cycling life. The gel membrane coated electrode prepared by PSS provides a new idea for the development of MCDI.

Microfluidic-Assembled Covalent Organic Frameworks@Ti3 C2 Tx MXene Vertical Fibers for High-Performance Electrochemical Supercapacitors

The delicate design of innovative and sophisticated fibers with vertical porous skeleton and eminent electrochemical activity to generate directional ionic pathways and good faradic charge accessibility is pivotal but challenging for realizing high-performance fiber-shaped supercapacitors (FSCs). Here, hierarchically ordered hybrid fiber combined vertical-aligned and conductive Ti3 C2 Tx MXene (VA-Ti3 C2 Tx ) with interstratified electroactive covalent organic frameworks LZU1 (COF-LZU1) by one-step microfluidic synthesis is developed. Due to the incorporation of vertical channels, abundant redox active sites and large accessible surface area throughout the electrode, the VA-Ti3 C2 Tx @COF-LZU1 fibers express exceptional gravimetric capacitance of 787 F g-1 in a three-electrode system. Additionally, the solid-state asymmetric FSCs deliver a prominent energy density of 27 Wh kg-1 , capacitance of 398 F g-1 and cycling life of 20 000 cycles. The key to high energy storage ability originates from the decreased ions adsorption energy and ameliorative charge density distribution in vertically aligned and active hybrid fiber, accelerating ions transportation/accommodation and interfacial electrons transfer. Benefiting from excellent electrochemical performance, the FSCs offer sufficient energy supply to power watches, flags, and digital display tubes as well as be integrated with sensors to detect pulse signals, which opens a promising route for architecting advanced fiber toward the carbon neutrality market beyond energy-storage technology.

Capacitive deionization system with ultra-high salt adsorption performance: from lab design to agricultural applications

Capacitive deionization is an emerging water desalination technology for industrial applications. Recent advancements in electrode design and system development have led to the reporting of ultra-high salt adsorption performance, benefiting its potential application in agricultural water treatment at a potentially low cost. In this study, we provide a comprehensive summary of the porous electrode design strategy to achieve ultra-high ion adsorption performance, considering factors such as experimental parameters, chemically tuned material properties, redox chemistry and smart nanoarchitecture for future electrode design. Furthermore, we endeavor to establish a correlation between capacitive deionization (CDI) technology and its applicability in the agricultural sector, specifically concentrating on water treatment with an emphasis on undesirable ions associated with salinity, hardness, and heavy metals, to achieve harmless irrigation. Additionally, to ensure the efficient and cost-effective application of CDI systems in agriculture, a thorough overview of the literature on CDI cost analysis is presented. By addressing these aspects, we anticipate that ultra-high salt adsorption CDI systems hold great promise in future agricultural applications.

Electrode Materials for Desalination of Water via Capacitive Deionization

Recent years have seen the emergence of capacitive deionization (CDI) as a promising desalination technique for converting sea and wastewater into potable water, due to its energy efficiency and eco-friendly nature. However, its low salt removal capacity and parasitic reactions have limited its effectiveness. As a result, the development of porous carbon nanomaterials as electrode materials have been explored, while taking into account of material characteristics such as morphology, wettability, high conductivity, chemical robustness, cyclic stability, specific surface area, and ease of production. To tackle the parasitic reaction issue, membrane capacitive deionization (mCDI) was proposed which utilizes ion-exchange membranes coupled to the electrode. Fabrication techniques along with the experimental parameters used to evaluate the desalination performance of different materials are discussed in this review to provide an overview of improvements made for CDI and mCDI desalination purposes.

Synergistic effect of intercalation and EDLC electrosorption of 2D/3D interconnected architectures to boost capacitive deionization for water desalination via MoSe2/mesoporous carbon hollow spheres

Transition-metal dichalcogenides can be used for capacitive deionization (CDI) via pseudocapacitive ion intercalation/de-intercalation due to their unique two-dimensional (2D) laminar structure. MoS₂ has been extensively studied in the hybrid capacitive deionization (HCDI), but the desalination performance of MoS₂-based electrodes remains only 20-35 mg g^-1 on average. Benefiting from the higher conductivity and larger layer spacing of MoSe₂ than MoS₂, it is expected that MoSe₂ would exhibit a superior HCDI desalination performance. Herein, for the first time, we explored the use of MoSe₂ in HCDI and synthesized a novel MoSe₂/MCHS composite material by utilizing mesoporous carbon hollow spheres (MCHS) as the growth substrate to inhibit the aggregation and improve the conductivity of MoSe₂. The as-obtained MoSe₂/MCHS presented unique 2D/3D interconnected architectures, allowing for synergistic effects of intercalation pseudocapacitance and electrical double layer capacitance (EDLC). An excellent salt adsorption capacity of 45.25 mg g^- 1 and a high salt removal rate of 7.75 mg g^- 1 min^-1 were achieved in 500 mg L^- 1 NaCl feed solution at an applied voltage of 1.2 V in batch-mode tests. Moreover, the MoSe₂/MCHS electrode exhibited outstanding cycling performance and low energy consumption, making it suitable for practical applications. This work demonstrates the promising application of selenides in CDI and provides new insights for ration design of high-performance composite electrode materials.

Enhanced Pseudo-Capacitance Process in Nanoarchitectural Layered Double Hydroxide Nanoarrays Hollow Nanocages for Improved Capacitive Deionization Performance

Layered double hydroxides (LDHs) are perceived as a hopeful capacitive deionization (CDI) faradic electrode for Cl^- insertion due to its tunable composition, excellent anion exchange capacity, and fast redox activity. Nevertheless, the self-stacking and inferior electrical conductivity of the two-dimensional structure of LDH lead to unsatisfactory CDI performance. Herein, the three-dimensional (3D) hollow nanocage structure of CoNi-layered double hydroxide/carbon composites is well designed as a CDI anode by cation etching of the pre-carbonized ZIF-67 template. C/CoNi-LDH has a unique 3D hollow nanocage structure and abundant pore features, which can effectively suppress the self-stacking of LDH sheets and facilitate the transport of ions. Moreover, the introduced amorphous carbon layer can act as a conductive network. When employed as the CDI anode, C/CoNi-LDH exhibited a high Cl^- removal capacity of 60.88 mg g^-1 and a fast Cl^- removal rate of 18.09 mg g^-1 min^-1 at 1.4 V in 1000 mg L^-1 NaCl solution. The mechanism of the Cl^- intercalation pseudo-capacitance reaction of C/CoNi-LDH is revealed by electrochemical kinetic analysis and ex situ characterization. This study provides vital guidance for the design of high-performance electrodes for CDI.

Controlled fabrication of nitrogen-doped porous carbon foam with refined hierarchical architectures for desalination via capacitive deionization

Porous carbon materials have been regarded as a promising alternative to activated carbon for desalination via capacitive deionization (CDI) due to refined architectures and functionalities. However, it is still challenging to obtain a controlled hierarchical pore structure and considerable nitrogen-doped content by convenient method. Herein, nitrogen-doped hierarchical porous carbon foams (NHCFs) with different microstructural features, nitrogen contents and nitrogen species were successfully fabricated via a stepwise pyrolysis carbonization strategy using easily available melamine foam. Due to the synergistic effect of hierarchical porous structure and doped nitrogen, the optimized NHCF sample carbonized at 800℃ (NHCF-800) exhibited a maximum desalination capacity of 30.1 mg g^-1 at the optimal operating parameters (500 mg/L NaCl solution, 1.2 V) and an excellent regeneration performance after 50 continuous adsorption-desorption cycles. Furthermore, density functional theory (DFT) was also conducted to elaborate the disparity of sodium adsorption energy among the nitrogen species for in-depth understanding, and it mainly benefits from the ascendency of the pyrrolic-N and pyridinic-N over the graphitic-N dopant. This work paves the way of rational regulation of nitrogen-doped process and hierarchical porous structure carbon as CDI electrode materials for desalination.

Ti3 C2 -MXene Partially Derived Hierarchical 1D/2D TiO2 /Ti3 C2 Heterostructure Electrode for High-Performance Capacitive Deionization

Constructing faradaic electrode with superior desalination performance is important for expanding the applications of capacitive deionization (CDI). Herein, a simple one-step alkalized treatment for in situ synthesis of 1D TiO₂ nanowires on the surface of 2D Ti₃ C₂ nanosheets, forming a Ti₃ C₂ -MXene partially derived hierarchical 1D/2D TiO₂ /Ti₃ C₂ heterostructure as the cathode electrode is reported. Cross-linked TiO₂ nanowires on the surface help avoid layer stacking while acting as the protective layer against contact of internal Ti₃ C₂ with dissolved oxygen in water. The inner Ti₃ C₂ MXene nanosheets cross over the TiO₂ nanowires can provide abundant active adsorption sites and short ion/electron diffusion pathways. . Density functional theory calculations demonstrated that Ti₃ C₂ can consecutively inject electrons into TiO₂ , indicating the high electrochemical activity of the TiO₂ /Ti₃ C₂ . Benefiting from the 1D/2D hierarchical structure and synergistic effect of TiO₂ and Ti₃ C₂ , TiO₂ /Ti₃ C₂ heterostructure presents a favorable hybrid CDI performance, with a superior desalination capacity (75.62 mg g^-1 ), fast salt adsorption rate (1.3 mg g^-1 min^-1 ), and satisfactory cycling stability, which is better than that of most published MXene-based electrodes. This study provides a feasible partial derivative strategy for construction of a hierarchical 1D/2D heterostructure to overcome the restrictions of 2D MXene nanosheets in CDI.

Ultrahigh Content Boron and Nitrogen Codoped Hierarchically Porous Carbon Obtained from Biomass Byproduct Okara for Capacitive Deionization

Capacitive deionization (CDI) is an environmentally friendly, energy efficient, and low cost water purification technique in comparison with other conventional techniques, and it has attracted considerable attention in recent years. Here, we use biomass byproduct okara as the starting material to fabricate a boron and nitrogen codoped hierarchically porous carbon (BNC) with ultrahigh heteroatom contents and abundant in-plane nanoholes for CDI application. With the interconnected hierarchical porous structure, the BNC not only exhibits a large surface area (647.0 m³ g^-1) for the adsorption of ions but also offers abundant ion transport channels to access the entire internal surface. Meanwhile, the ultrahigh dopants' content of B (11.9 at%) and N (14.8 at%) further gives rise to the increased surface polarity and enhanced capacitance for BNC. Owing to these favorable properties, BNC exhibits top-level salt adsorption capacity (21.5 mg g^-1) and charge efficiency (59.5%) at the initial NaCl concentration of ∼500 mg L^-1. Moreover, we performed first-principle simulations to explore the different effects between N-doping and N,B-codoping on the capacitive property, which indicate that the boron and nitrogen codoping of carbon can largely increase the quantum capacitance over the double layer capacitance. The results of this work suggest a promising prospect for the BNC material in practical CDI application.

MXene Nanosheets Induce Efficient Iron Selenide Active Sites to Boost the Electrocatalytic Hydrogen Evolution Reaction

Along with the widespread utilization of hydrogen energy, the rise of highly active hydrogen evolution electrocatalysts with affordable costs presently becomes a substantial crux of this emerging domain. In this work, we demonstrate a feasible and convenient in situ seed-induced growth strategy for the construction of small-sized FeSe₂ nanoparticles decorated on two-dimensional (2D) superthin Ti₃C₂T_x MXene sheets (FeSe₂/Ti₃C₂T_x) through a manipulated bottom-up synthetic procedure. By virtue of the distinctive 0D/2D heterostructures, abundant exposed surface area, well-distributed FeSe₂ catalytic centers, strong surface electronic coupling, and high electrical conductivity, the resultant FeSe₂/Ti₃C₂T_x nanoarchitectures are endowed with a superior electrocatalytic hydrogen evolution capacity including a competitive onset potential of 89 mV, a favorable Tafel slope of 78 mV dec^-1, and a long-period stability, significantly better than that of the pristine FeSe₂ and Ti₃C₂T_x catalysts.

Intelligent Coatings with Controlled Wettability for Oil-Water Separation

Intelligent surfaces with controlled wettability have caught much attention in industrial oily wastewater treatment. In this study, a hygro-responsive superhydrophilic/underwater superoleophobic coating was fabricated by the liquid-phase deposition of SiO₂ grafted with perfluorooctanoic acid. The wettability of the surface could realize the transformation from superhydrophilicity/underwater superoleophobicity (SHI/USOB) to superhydrophobicity/superoleophilicity (SHB/SOI), both of which exhibited excellent separation performance towards different types of oil-water mixtures with the separation efficiency higher than 99%. Furthermore, the long-chain perfluoroakyl substances on the surface could be decomposed by mixing SiO₂ with TiO₂ nanoparticles under UV irradiation, which could reduce the pollution to human beings and environment. It is anticipated that the prepared coating with controlled wettability could provide a feasible solution for oil-water separation.

Polyaniline coated MOF-derived Mn2O3 nanorods for efficient hybrid capacitive deionization

Mn-based oxides are efficient pseudocapacitive electrode materials and have been investigated for capacitive deionization (CDI). However, their poor conductivity seriously affects their desalination performance. In this work, polyaniline coated Mn₂O₃ nanorods (PANI/Mn₂O₃) are synthesized by oxidizing a Mn-based metal organic framework (MOF) and subsequent in-situ chemical polymerization. The polyaniline not only acts as a conductive network for faradaic reactions of Mn₂O₃, but also enhances the desalination rate. PANI/Mn₂O₃ has a specific capacitance of 87 F g^-1 (at 1 A g^-1), superior to that of Mn₂O₃ nanorod (52 F g^-1 at 1 A g^-1). The hybrid CDI cell constructed with a PANI/Mn₂O₃ cathode and an active carbon anode shows a high desalination capacity of 21.6 mg g^-1, superior recyclability with only 11.3% desalination capacity decay after 30 desalination cycles and fast desalination rate of 2.2 mg g^-1 min^-1. PANI/Mn₂O₃ is a potential candidate for high performance CDI applications.