CuO nanorod arrays by gas-phase cation exchange for efficient photoelectrochemical water splitting

Efficient degradation of organics by ultrasonic piezoelectric effect on CuO-BTO/AFC composite

The recombination of photoexcited electron-hole pairs greatly limits the degradation performance of photocatalysts. Ultrasonic cavitation and internal electric field induced by the piezoelectric effect are helpful for the separation of electron-hole pairs and degradation efficiency. The activated foam carbon (AFC) owing to its high surface area is often used as the substrate to grow catalysts to provide more reactive active sites. In this work, CuO@BaTiO3(CuO@BTO) heterostructure is prepared by hydrothermal method on the surface of AFC to investigate the ultrasonic piezoelectric catalysis effect. X-ray diffraction (XRD), Raman spectroscopy, energy dispersive x-ray spectroscopy (EDS) and scanning electron microscopy (SEM) were used to analyze the structure and morphology of CuO-BTO/AFC composite. It is found that the CuO-BTO/AFC composite exhibits excellent piezo-catalytic performance for the degradation of organics promoted by ultrasonic vibration. The CuO-BTO/AFC composite can decompose methyl orange and methylene blue with degradation efficiency as high as 93.9% and 97.6% within 25 min, respectively. The mechanism of piezoelectricity enhanced ultrasound supported catalysis effect of system CuO-BTO/AFC is discussed. The formed heterojunction structure between BTO and CuO promotes the separation of positive and negative charges caused by the piezoelectric effect.

Integration of One-Dimensional (1D) Lead-Free Perovskite Microbelts onto Silicon for Ultraviolet-Visible-Near-Infrared (UV-vis-NIR) Heterojunction Photodetectors

Lead-free perovskites are considered to be candidates for next-generation photodetectors, because of their excellent charge carrier transport properties and low toxicity. However, their application in integrated circuits is hindered by their inadequate performance and size restrictions. To aim at the development of lead-free perovskite-integrated optoelectronic devices, a CsAg2I3/silicon (CAI/Si) heterojunction is presented in this work by using a spatial confinement growth method, where the in-plane growth of CAI microbelts with high-quality single-crystal characteristics is primarily dependent on the concentration of surrounding precursor solution. The fabricated photodetectors based on the CAI/Si heterojunctions exhibit a broad-spectrum detection capability in the ultraviolet-visible-near-infrared (UV-vis-NIR) range. In addition, the photodetectors show good photoelectric detection performance, including a maximum responsivity of 48.5 mA/W and detectivity of 1.13 × 1011 Jones, respectively. Besides, the photodetectors have a rapid response of 6.5/224 μs and good air stability for over 2 months. This work contributes a new idea to design next-generation optoelectronic devices with high integration density.

Efficient synthesis of 3D ZnO nanostructures on ITO surfaces for enhanced photoelectrochemical water splitting

New photoactive materials with uniform and well-defined morphologies were developed for efficient and sustainable photoelectrochemical (PEC) water splitting and hydrogen production. The investigation is focused on hydrothermal deposition of zinc oxide (ZnO) onto indium tin oxide (ITO) conductive surfaces and optimization of hydrothermal temperature for growing uniform sized 3D ZnO morphologies. Fine-tuning of hydrothermal temperature enhanced the scalability, efficiency, and performance of ZnO-decorated ITO electrodes used in PEC water splitting. Under UV light irradiation and using eco-friendly low-cost hydrothermal process in the presence of stable ZnO offered uniform 3D ZnO, which exhibited a high photocurrent of 0.6 mA/cm2 having stability up to 5 h under light-on and light-off conditions. The impact of hydrothermal temperature on the morphological properties of the deposited ZnO and its subsequent performance in PEC water splitting was investigated. The work contributes to advancement of scalable and efficient fabrication technique for developing energy converting photoactive materials.