Preprimed artificial lung for emergency use

Development of an implantable oxygenator with cross-flow pump

Thrombogenicity, a problem with long-term artificial lungs, is caused by blood-biomaterial interactions and is made worse by nonuniform flow, which also causes decreased gas exchange. To overcome these obstacles, we changed the inlet and added a uniform flow pump to our previous oxygenator design. Conventional membrane oxygenators have a (1/2)-inch port for the inlet of blood. These port structures make it difficult for the blood to flow uniformly in the oxygenator. In addition, the complex blood flow patterns that occur in the oxygenator, including turbulence and stagnation, lead to thrombogenicity. A cross-flow pump (CFP) can result in uniform blood flow to the inlet side of an oxygenator. In this study, we evaluated the usefulness of an integrated oxygenator with a fiber bundle porosity of 0.6 and a membrane surface area of 1.3 m2. The inlet part of the oxygenator is improved and better fits the outlet of the CFP. Each of the three models of the improved oxygenator has a different inlet taper angle. The computational fluid dynamics analysis showed that, compared with the original design, uniform flow of the integrated oxygenator improved by 88.8% at the hollow fiber membrane. With the integrated oxygenator, O2 transfer increased by an average of 20.8%, and CO2 transfer increased by an average of 35.5%. The results of our experiments suggest that the CFP, which produces a wide, uniform flow to the oxygenator, is effective in attaining high gas exchange performance.

Evaluation of Plasma Resistant Hollow Fiber Membranes For Artificial Lungs

Hollow fiber membranes (HFMs) used in artificial lungs (oxygenators) undergo plasma leakage (or wetting) in which blood plasma slowly fills the pores of the fiber wall, plasma leaks into gas pathways, and overall gas exchange decreases. To overcome this problem plasma resistant fibers are being developed that are skinned asymmetric or composite symmetric versions of microporous oxygenator fibers. This report evaluates several candidate plasma resistant HFMs in terms of their gas permeance and plasma resistance as measured in a surfactant wet out test. Five candidate fibers were compared with each other and with a control fiber. CO2 and O2 gas permeance (in ml/s/cm2/cm Hg) in the plasma resistant fibers ranged from 3.15E-04 to 1.71E-03 and 3.40E-04 to 1.08E-03, respectively, compared with 1.62E-02 and 1.77E-02 for the control fiber. Maximum dye bleed through for the plasma resistant fibers in the forced wet out test were significantly less than for the control fiber. CO2 gas permeance of a plasma resistant fiber imposes the greatest constraint upon artificial lung design for sufficient gas exchange. However, our results suggest sufficient plasma resistance can be achieved using special skinned and composite HFMs while maintaining an acceptable CO2 gas permeance for a broad range of artificial lung applications.

Design Progress of the Ultracompact Integrated Heart Lung Assist Device-Part 1: Effect of Vaned Diffusers on Gas-Transfer Performances

The integrated heart lung assist device (IHLAD) has been developed to overcome the problems of currently available extracorporeal membrane oxygenation devices. The integrated structure of a centrifugal blood pump and cylindrical bundle of polyolefin hollow-fibers has allowed a remarkably compact size for the device. This study deals with the design change of the IHLAD that added to the vaned diffuser between the impeller of the centrifugal pump and the hollow-fiber bundle with a view to enhancing the gas-transfer performance. Ex vivo gas-transfer performance tests were carried out, as well as hydrodynamic characteristics and hemolysis test using fresh goat blood. The oxygen transfer rate was generally improved, and the carbon dioxide removal rate was slightly improved. Intolerable amount of hemolysis (index of hemolysis= 0.177) was caused by the IHLAD, which must be resolved by improving the design in the future.

Biomaterial development for cardiopulmonary bypass

Cardiopulmonary bypass (CPB) is dependent on materials foreign to the patient for its successful application. When blood comes into contact with these so-called biomaterials, an inappropriate inflammatory response, which can be life-threatening in some patients, may develop. The reason for this inappropriate activation of host defence mechanisms is not entirely clear, however a number of strategies have evolved over the years to minimize this unwanted sequelae of CPB. These strategies include surface coating of the materials of the circuit, using new materials thought to improve biocompatibility, and using a number of pharmacological interventions designed to suppress the inflammatory response. Recently, there has been some evidence which indicates that the plasticizer employed in the polyvinyl chloride (PVC) tubing of the CPB circuit may play a part in the development of the inflammatory response. The work described in this paper tends to support this thesis. These studies showed that by washing the plasticizer from the surface of the PVC tubing, the biocompatibility, as reflected in the upregulation of CD11b on the surface of neutrophils, was enhanced. Furthermore, the use of non-plasticized substitutes for PVC had a similar effect. The benefit from removing the plasticizer was similar to that gained from surface coating with heparin, one of the conventional approaches to reducing the inflammatory response to CPB.