Colorimetric Method for the Determination of Ampicillin and Amoxicillin

Development and Validation of Ecofriendly HPLC-MS Method for Quantitative Assay of Amoxicillin, Dicloxacillin, and Their Official Impurity in Pure and Dosage Forms

Novel, accurate, selective, and rapid high-performance liquid chromatography mass spectrometry method was developed for simultaneous analysis of amoxicillin trihydrate, dicloxacillin sodium, and their official impurity 6-aminopenicillanic acid. The chromatographic separation was carried out by applying the mixture on a C₁₈ column (3.5 µm ps, 100 mm × 4.6 mm id) using acetonitrile:water (65 : 35 by volume) as a mobile phase within only 4 min. The quantitative analysis was executed using single quadrupole mass spectrometer in which electrospray ionization, selected ion monitoring, and negative mode were operated. The retention times were 1.61, 2.54, and 3.50 mins for amoxicillin, 6-aminopenicillanic acid, and dicloxacillin, respectively. The method was validated in linear ranges of 2-28 µg mL^-1, 2-35 µg mL^-1, and 1-10 µg mL^-1 for amoxicillin, dicloxacillin, and 6-aminopenicillanic acid, respectively. The results obtained from the suggested HPLC/MS were statistically compared with those obtained from the reported HPLC method, where no significant difference appeared respecting accuracy and precision. According to the analytical eco-scale assessment method, the proposed method was proved to be greener than the reported one, where the analysis time and the amount of the wasted effluent decreased.

Diffusion and Controlled Release in Physically Crosslinked Poly (Vinyl Alcohol)/Iota-Carrageenan Hydrogel Blends

This paper reports the obtaining of poly (vinyl alcohol) and i-carrageenan blend hydrogels by physical crosslinking (consecutive freeze-thaw cycles). The two polymers were completely miscible in the weight ratio interval used in this study, as determined by solution viscometry data. Strong interactions through hydrogen bonding and forming of mixed interpolymer crystalline domains were observed, which are responsible for the formation of stable drug release-tunable matrices. The release profiles of three model antibiotic drugs (amoxicillin, tetracycline hydrochloride, and gentamicin sulfate) were assessed in a pH interval between 3 and 7.3. They were found to be strongly dependent on the drug chemistry, mesh size of the hydrogels, swelling mechanism, and pH of the release medium. A decrease of up to 40% in the release rates and up to 10% in the diffusion coefficients of the model drugs was registered with the increase in i-carrageenan content.

Determination of ampicillin and amoxycillin by flow injection chemiluminescence method based on their enhancing effects on the luminol-periodate reaction

In this work, a new flow injection chemiluminescence method is described for the determination of ampicillin and amoxycillin. The method is based on the strong enhancing effects of these antibiotics on the luminol-periodate reaction. The present method allows the measurements of ampicillin in the range 0.02-1.0 mg/L range and amoxycillin in the range 0.1-10.0 mg/L range with the relative standard deviations within 0.8-2.0%. The sampling frequency was calculated about 90/h. The method was successfully applied to the determination of ampicillin and amoxycillin in pharmaceutical preparations. A brief discussion on the possible chemiluminescence reaction mechanism is presented.

Kinetic spectrophotometric determination of ampicillin and amoxicillin in dosage forms

A kinetic spectrophotometric method has been developed for the determination of ampicillin (I) and amoxicillin (II). The method involves hydrolysis of the antibiotics with 1.0 M HCl, neutralization with 1.0 M NaOH followed by addition of palladium(II) chloride in the presence of 2 M KCl. The produced yellow colour is measured at 335 nm. The proposed method is valid over the concentration range 8-40 microg/ml and 10-40 microg/ml for I and II respectively with minimum detectability of 0.73 microg/ml and 0.76 microg/ml for I and II respectively. The determination of the studied compounds adopting the fixed concentration method is feasible with the calibration equations obtained, but the fixed time method has been found to be more applicable. The proposed method was applied to commercial dosage forms and the results obtained were in good agreement with those given by USP method.