Influence of Crosslink Density on Mechanical Properties of Natural Rubber Vulcanizates

Transparent bamboo as a replacement for glass: Effects of lignin decolorisation methods on weatherability

Transparent bamboo proved to be a promising substitute for glass due to its high light transmittance and excellent mechanical properties. Nevertheless, it was susceptible to outdoor weathering, which negatively affected its physical and mechanical properties. In this study, two decolorisation methods, namely the delignification method and the lignin modification method, were used to produce transparent bamboos with epoxy resin, referred to as DL-TB and LM-TB, respectively. The changes in surface color, optical and mechanical properties, wettability, thermal stability, and thermal insulation properties of transparent bamboo during accelerated UV weathering were evaluated. Additionally, the deterioration mechanism of DL-TB and LM-TB was investigated. The findings revealed that DL-TB demonstrated better transparency and mechanical properties than LM-TB, although it exhibited lower thermal insulation properties. Furthermore, DL-TB demonstrated enhanced color stability and higher hydrophobicity on weathered surfaces than LM-TB. Unexpectedly, the tensile properties of both two transparent bamboos significantly improved after weathering, especially for LM-TB, which was due to the EP post-curing and the formation of more hydrogen bonds between lignin and EP. These observations revealed that lignin played a key role in the photodegradation process of transparent bamboo, but further attempts should be made in future studies to improve its color stability.

Abrasion Behaviors of Silica-Reinforced Solution Styrene-Butadiene Rubber Compounds Using Different Abrasion Testers

Solution styrene-butadiene rubber (SSBR) is widely used to improve the properties of tire tread compounds. Tire wear particles (TWPs), which are generated on real roads as vehicles traverse, represent one of significant sources of microplastics. In this study, four SSBR compounds were prepared using two SSBRs with high styrene (STY samples) and 1,2-unit (VIN samples) contents, along with dicyclopentadiene resin. The abrasion behaviors were investigated using four different abrasion testers: cut and chip (CC), Lambourn, DIN, and laboratory abrasion tester (LAT100). The abrasion rates observed in the Lambourn and LAT100 abrasion tests were consistent with each other, but the results of CC and DIN abrasion tests differed from them. The addition of the resin improved the abrasion rate and resulted in the generation of large wear particles. The abrasion rates of STY samples in the Lambourn and LAT100 abrasion tests were lower than those of VIN samples, whereas the values in the CC and DIN abrasion tests were higher than those of VIN samples. The wear particles were predominantly larger than 1000 μm, except for the VIN sample in the DIN abrasion test. However, TWPs > 1000 μm are rarely produced on real roads. The size distributions of wear particles > 1000 μm were 74.0-99.5%, 65.9-93.4%, 7.2-95.1%, and 37.5-83.0% in the CC, Lambourn, DIN, and LAT100 abrasion tests, respectively. The size distributions of wear particles in the Lambourn and LAT100 abrasion tests were broader than those in the other tests, whereas the distributions in the CC abrasion test were narrower. The abrasion patterns and the morphologies and size distributions of wear particles generated by the four abrasion tests varied significantly, attributable to differences in the bound rubber contents, crosslink densities, and tensile properties.

Natural Rubber/Styrene-Butadiene Rubber Blend Composites Potentially Applied in Damping Bearings

Natural rubber (NR) composites have been widely applied in damping products to reduce harmful vibrations, while rubber with only a single composition barely meets performance requirements. In this study, rubber blend composites including various ratios of NR and styrene butadiene rubber (SBR) were prepared via the conventional mechanical blending method. The effects of the rubber components on the compression set, compression fatigue temperature rising and the thermal oxidative aging properties of the NR/SBR blend composites were investigated. Meanwhile, the dynamic mechanical thermal analyzer and rubber processing analyzer were used to characterize the dynamic viscoelasticity of the NR/SBR blend composites. It was shown that, with the increase in the SBR ratio, the vulcanization rate of the composites increased significantly, while the compression fatigue temperature rising of the composites decreased gradually from 47 °C (0% SBR ratio) to 31 °C (50% SBR ratio). The compression set of the composites remained at ~33% when the SBR ratio was no more than 20%, and increased gradually when the SBR ratio was more than 20%.

Optimized End Functionality of Silane-Terminated Liquid Butadiene Rubber for Silica-Filled Rubber Compounds

As the world is shifting from internal combustion engine vehicles to electric vehicles in response to environmental pollution, the tire industry has been conducting research on tire performance to meet the requirements of electric vehicles. In this experiment, functionalized liquid butadiene rubber (F-LqBR) with triethoxysilyl groups at both ends was introduced into a silica-filled rubber compound as a substitute for treated distillate aromatic extract (TDAE) oil, and comparative evaluation was conducted according to the number of triethoxysilyl groups. The results showed that F-LqBRs improved silica dispersion in the rubber matrix through the formation of chemical bonds between silanol groups and the base rubber, and reduced rolling resistance by limiting chain end mobility and improving filler-rubber interaction. However, when the number of triethoxysilyl groups in F-LqBR was increased from two to four, self-condensation increased, the reactivity of the silanol groups decreased, and the improvement of properties was reduced. As a result, the optimized end functionality of triethoxysilyl groups for F-LqBR in silica-filled rubber compound was two. The 2-Azo-LqBR with the optimized functionality showed an improvement of 10% in rolling resistance, 16% in snow traction, and 17% in abrasion resistance when 10 phr of TDAE oil was substituted.

Variation in Abundance Ratio of Isoprene and Dipentene Produced from Wear Particles Composed of Natural Rubber by Pyrolysis Depending on the Particle Size and Thermal Aging

Tire wear particles (TWPs) are generated by friction between the road and the tire. TWPs are one of the major microplastics found in environmental samples, such as road dust, particulate matter (PM), and sediment. TWP contents in environmental samples are generally analyzed using the pyrolysis technique. Tire tread compounds of heavy vehicles are usually composed of natural rubber (NR). Isoprene and dipentene are the principal pyrolysis products of NR, and dipentene is employed as the key marker for the determination of the TWP contents. In this study, an NR abrasion specimen was thermally aged, and an abrasion test was performed to obtain the wear particles. The influence of the wear particle size and thermal aging on the pyrolysis behavior of NR was investigated. The isoprene/dipentene ratio exponentially increased as the wear particle size decreased, and it was also increased by the thermal aging of the abrasion specimen. The increased isoprene/dipentene ratio by thermal aging was explained by increasing the crosslink density. Using the relationship between the wear particle size and the isoprene/dipentene ratio, it is possible to estimate the isoprene/dipentene ratio for very small TWP such as PM. The experimental results concluded that the wear particle size and thermal aging affect the formation of the key pyrogenic products, and the influencing factors should be considered for the quantification of TWP contents in the environmental samples.

Effect of Single-Walled Carbon Nanotubes on the Cross-Linking Process in Natural Rubber Vulcanization

In this study, the effect of single-walled carbon nanotubes (SWCNTs) on the cross-linking of natural rubber (NR) using organic peroxides was investigated. NR-SWCNTs nanocomposites were prepared in an open two-roller mill followed by vulcanization with the compression molding process. Three different organic peroxides, 1,1-bis(tert-butylperoxy)-3,3,5-trimethylcyclohexane (T29), dicumyl peroxide (DCP), and 2,5-bis(tert-butylperoxy)-2,5-dimethyl-3-hexyne (T145), were used as vulcanizing agents. SWCNTs promote a remarkable reduction in the vulcanization time and increase the degree of cross-linking of vulcanized rubber when compared with neat or natural rubber-carbon-black composites; the same tendency was obtained in the NR-SWCNTs vulcanized with sulfur. Additionally, the mechanical performance of the NR-SWCNTs composites was significantly improved up to 75, 83, 27, and 10% for tensile strength, moduli, tear strength, and hardness. Raman spectroscopy studies evidence the occurrence of reaction between nanotube walls and free radicals generated from using organic peroxides during the vulcanization process. These results demonstrate that the incorporation of SWCNTs in combination with the use of organic peroxides for the NR vulcanization represents a potential alternative for the improvement of the physicochemical properties of NR composites.

New Insight into Rubber Composites Based on Graphene Nanoplatelets, Electrolyte Iron Particles, and Their Hybrid for Stretchable Magnetic Materials

New and soft composites with good mechanical stretchability are constantly addressed in the literature due to their use in various industrial applications such as soft robotics. The stretchable magnetic materials presented in this work show a promising magnetic effect of up to 28% and improved magnetic sensitivity. The composites are soft in nature and possess hardness below 65. These composites were prepared by mixing silicone rubber with fillers such as graphene nanoplatelets (GNP), electrolyte-iron particles (EIP), and their hybrid via solution mixing. The final composites were cured at room temperature for 24 h and their isotropic and anisotropic properties were studied and presented. The mechanical properties under compressive and tensile strain were studied in detail. The results show that the compressive modulus was 1.73 MPa (control) and increased to 3.7 MPa (GNP) at 15 per hundred parts of rubber (phr), 3.2 MPa (EIP), and 4.3 MPa (hybrid) at 80 phr. Similarly, the mechanical stretchability was 112% (control) and increased to 186% (GNP) at 15 phr, 134% (EIP), and 136% (hybrid) at 60 phr. Thus, GNP emerges as a superior reinforcing filler with high stiffness, a high compressive modulus, and high mechanical stretchability. However, the GNP did not show mechanical sensitivity under a magnetic field. Therefore, the hybrids containing GNP and EIP were considered and an improved mechanical performance with magnetic sensitivity was noticed and reported. The mechanism involves the orientation of EIP under a magnetic field causing a magnetic effect, which is 28% for EIP and 5% for hybrid.

Effects of the Diamine Chain End Functionalized Liquid Butadiene Rubber as a Processing Aid on the Properties of Carbon-Black-Filled Rubber Compounds

The implementation of vehicle electrification and autonomous driving technologies has recently emphasized the importance of abrasion resistance and fuel efficiency of truck bus radial (TBR) tire treads that undergo high loads and long driving times. In this study, a functionalized liquid butadiene rubber (F-LqBR) was introduced to replace the treated distillate aromatic extracted (TDAE) oil as a way to improve abrasion resistance and fuel efficiency in the TBR tire tread compound and to solve the oil migration. First, radical polymerization was used to synthesize nonfunctionalized LqBR (N-LqBR) and amino-LqBR with an amine group at the chain ends. The synthesized LqBRs were then substituted in place of TDAE oil to manufacture carbon-black-filled natural rubber (NR) compounds and to evaluate their physical properties. The results show that LqBRs improved the migration resistance and enhanced the abrasion resistance by lowering the glass transition temperature (T_g) of the compound. In particular, amino-LqBR improved carbon black dispersion in the rubber matrix through a chemical bond between the functional group of the carbon black surface and the base rubber. In conclusion, amino-LqBR successfully served as a processing aid in a carbon black-filled NR compound while simultaneously enhancing its fuel efficiency and abrasion resistance.

The link between swelling ratios and physical properties of EPDM rubber compound having different oil amounts

This new observation demonstrated that an increase in oil amounts within ethylene propylene diene monomer (EPDM) compounds decreased the crosslink density and the storage modulus but increase the elongation at break after tensile testing. The compounds with high oil amounts were observed to release oil particles when dissolved in toluene solutions and that increased their swell ratios. Consequently, the crosslink density had a perfect negative linear correlation with the elongation at break and a strong power-law correlation with the swell ratios. This work guides the material chemists and engineers during compound formulations when an increase in oil amounts is required.

Natural Rubber Blend Optimization via Data-Driven Modeling: The Implementation for Reverse Engineering

Natural rubber formulation methodologies implemented within industry primarily implicate a high dependence on the formulator’s experience as it involves an educated guess-and-check process. The formulator must leverage their experience to ensure that the number of iterations to the final blend composition is minimized. The study presented in this paper includes the implementation of blend formulation methodology that targets material properties relevant to the application in which the product will be used by incorporating predictive models, including linear regression, response surface method (RSM), artificial neural networks (ANNs), and Gaussian process regression (GPR). Training of such models requires data, which is equal to financial resources in industry. To ensure minimum experimental effort, the dataset is kept small, and the model complexity is kept simple, and as a proof of concept, the predictive models are used to reverse engineer a current material used in the footwear industry based on target viscoelastic properties (relaxation behavior, tanδ, and hardness), which all depend on the amount of crosslinker, plasticizer, and the quantity of voids used to create the lightweight high-performance material. RSM, ANN, and GPR result in prediction accuracy of 90%, 97%, and 100%, respectively. It is evident that the testing accuracy increases with algorithm complexity; therefore, these methodologies provide a wide range of tools capable of predicting compound formulation based on specified target properties, and with a wide range of complexity.

Effect of 3-Mercaptopropyltriethoxysilane Modified Illite on the Reinforcement of SBR

To achieve the sustainable development of the rubber industry, the substitute of carbon black, the most widely used but non-renewable filler produced from petroleum, has been considered one of the most effective ways. The naturally occurring illite with higher aspect ratio can be easily obtained in large amounts at lower cost and with lower energy consumption. Therefore, the expansion of its application in advanced materials is of great significance. To explore their potential use as an additive for reinforcing rubber, styrene butadiene rubber (SBR) composites with illites of different size with and without 3-mercaptopropyltriethoxysilane (KH580) modification were studied. It was found that the modification of illite by KH580 increases the K-illite/SBR interaction, and thus improves the dispersion of K-illite in the SBR matrix. The better dispersion of smaller size K-illite with stronger interfacial interaction improves the mechanical properties of SBR remarkably, by an increment of about nine times the tensile strength and more than ten times the modulus. These results demonstrate, except for the evident effect of particle size, the great importance of filler-rubber interaction on the performance of SBR composites. This may be of great significance for the potential wide use of the abundant naturally occurring illite as substitute filler for the rubber industry.

Rubber Rail Pad Reinforced by Modified Silica Using GPTMS and Sulfenamide Accelerator

The interaction between silica and rubber is very important for the production of high performance rubber. Silica surface modification with silane is a general method that aims to enhance the reinforcement efficiency of silica. In this study, a new surface modification of silica with silane and the chemical reaction with sulfenamide accelerator were investigated. The (gamma-glycidoxypropyl) trimethoxysilane (GPTMS) was used as a silane. The N-cyclohexyl-2-benzothiazole sulfenamide (CBS) and N-tert-butyl-2-benzothiazole sulfenamide (TBBS) were used as sulfenamide accelerators. The FTIR spectra results indicate that the GPTMS and sulfenamide accelerators (CBS and TBBS) could successfully form on the silica surface. The new modification is capable of significantly enhancing the reinforcement efficiency; more than the conventional silica surface modification by GPTMS (m-silica). In particular, modifying silica with GPTMS and TBBS (m-silica-TBBS) is capable of increasing the crosslink density and mechanical properties more efficiently than modified silica with GPTMS and CBS (m-silica-CBS), m-silica, silica (unmodified), and unfilled natural rubber. This is due to the presence of GPTMS, which plays an important role in increasing the chemical cross-linking in the rubber chain, while TBBS, as a sulfenamide accelerator, provides a high accelerator to sulfur ratio, which is able to give a more efficient vulcanization. With the reinforcement of a rubber rail pad with silica surface modification, the results indicate that the increment of m-silica-TBBS loading could reduce the deformation percentage of the rubber rail pad more than m-silica and m-silica loading. This is mainly due to the static spring improvement, which results in a stiffer material.

Bromide and Chloride Ionic Liquids Applied to Enhance the Vulcanization and Performance of Natural Rubber Biocomposites Filled with Nanosized Silica

In this study, the possibility of using ionic liquids (ILs) as auxiliary substances improving the vulcanization and physicochemical properties of natural rubber (NR) biocomposites filled with nanosized silica was investigated. Hence, the influence of ILs with bromide and chloride anions and various cations, i.e., alkylimidazolium, alkylpyrrolidinium and alkylpiperidinium cation, on the curing characteristics and crosslink density of NR compounds was determined. Furthermore, the effect of nanosized silica and ILs on the functional properties of the obtained vulcanizates, including mechanical properties under static and dynamic conditions, hardness, thermal stability and resistance to thermo-oxidative aging, were explored. Applying nanosized silica improved the processing safety of NR compounds but significantly increased the optimal vulcanization time compared to the unfilled rubber. ILs significantly improved the cure characteristics of NR compounds by increasing the rate of vulcanization and the crosslink density of NR biocomposites. Consequently, the tensile strength and hardness of the vulcanizates significantly increased compared to that without ILs. Moreover, the use of nanosized silica and ILs had a favorable impact on the thermal stability of the vulcanizates and their resistance to prolonged thermo-oxidation.

Synthesis and Vulcanization of Polymyrcene and Polyfarnesene Bio-Based Rubbers: Influence of the Chemical Structure over the Vulcanization Process and Mechanical Properties

The overuse of fossil-based resources to produce thermoplastic materials and rubbers is dramatically affecting the environment, reflected in its clearest way as global warming. As a way of reducing this, multiple efforts are being undertaken including the use of more sustainable alternatives, for instance, those of natural origin as the main feedstock alternative, therefore having a lower carbon footprint. Contributing to this goal, the synthesis of bio-based rubbers based on β-myrcene and trans-β-farnesene was addressed in this work. Polymyrcene (PM) and polyfarnesene (PF) were synthesized via coordination polymerization using a neodymium-based catalytic system, and their properties were compared to the conventional polybutadiene (PB) and polyisoprene (PI) also obtained via coordination polymerization. Moreover, different average molecular weights were also tested to elucidate the influence over the materials' properties. The crosslinking of the rubbers was carried out via conventional and efficient vulcanization routes, comparing the final properties of the crosslinking network of bio-based PM and PF with the conventional fossil-based PB and PI. Though the mechanical properties of the crosslinked rubbers improved as a function of molecular weight, the chemical structure of PM and PF (with 2 and 3 unsaturated double bonds, respectively) produced a crosslinking network with lower mechanical properties than those obtained by PB and PI (with 1 unsaturated double bond). The current work contributes to the understanding of improvements (in terms of crosslinking parameters) that are required to produce competitive rubber with good sustainability/performance balance.

Graphene Nanoplatelets as a Replacement for Carbon Black in Rubber Compounds

In this work, we evaluated the processing and reinforcement characteristics of both carbon black (CB) and graphene nanoplatelets (GNPs) within a nitrile butadiene rubber (NBR) matrix. The aspect ratio of the GNPs was measured using atomic force microscopy (AFM) and related to the dispersion and agglomeration within the NBR matrix, as observed by scanning electron microscopy (SEM). The relationship between GNP aspect ratio and mechanical properties was studied by micromechanical modelling. The tensile and tear properties of NBR after compounding with GNPs were enhanced to a greater extent compared to carbon black, while curing times were smaller and scorch times longer, indicating some of the advantages of using GNPs. Overall, the inherent properties of GNPs along with their geometry led to the production of better-performing rubber compounds that can replace their CB-filled counterparts in applications where flexibility, tear strength and compliance are important. The influence of processing on dispersion, orientation and agglomeration of flakes was also highlighted with respect to the Young’s modulus of the NBR compounds.

The Synergistic Effect of Dibenzyldithiocarbamate Based Accelerator on the Vulcanization and Performance of the Silica-Filled Styrene-Butadiene Elastomer

This work focused on studying the effect of dibenzyldithocarbamate vulcanization accelerator on the curing characteristics and performance of styrene–butadiene elastomer (SBR) filled with nanosized silica. A dibenzyldithocarbamate derivative was applied as an additional accelerator to enhance the efficiency and the rate of sulfur vulcanization in the presence of two other accelerators, i.e., N-cyclohexyl-2-benzothiazole sulfenamide (CBS) and/or 1,3-diphenylguanidine (DPG). Furthermore, the possibility of reducing the amount of zinc oxide (ZnO) and the elimination of CBS and DPG from elastomer compounds using dibenzyldithiocarbamate accelerator was tested. Dibenzyldithocarbamate derivative applied with other accelerators (especially CBS) effectively enhances the efficiency of SBR vulcanization by reducing the optimal vulcanization time and increasing the crosslink density of the vulcanizates despite the lower amount of ZnO. Moreover, vulcanizates with dibenzyldithocarbamate demonstrate higher tensile strength while having a smaller content of CBS or DPG compared to the reference SBR composites. Thus, the synergistic effect of dibenzydithiocarbamate derivative on the vulcanization and performance of SBR was confirmed. Furthermore, dibenzyldithocarbamate derivative enables the amount of ZnO to be reduced by 40% without harmful influence on the crosslink density and performance of the vulcanizates. Finally, it is possible to replace CBS with a dibenzyldithiocarbamate derivative without the crosslink density and tensile strength of the vulcanizates being adversely affected, while improving their resistance to thermo-oxidative aging.

Systematic optimization of visible light-induced crosslinking conditions of gelatin methacryloyl (GelMA)

Gelatin methacryloyl (GelMA) is one of the most widely used photo-crosslinkable biopolymers in tissue engineering. In in presence of an appropriate photoinitiator, the light activation triggers the crosslinking process, which provides shape fidelity and stability at physiological temperature. Although ultraviolet (UV) has been extensively explored for photo-crosslinking, its application has been linked to numerous biosafety concerns, originated from UV phototoxicity. Eosin Y, in combination with TEOA and VC, is a biosafe photoinitiation system that can be activated via visible light instead of UV and bypasses those biosafety concerns; however, the crosslinking system needs fine-tuning and optimization. In order to systematically optimize the crosslinking conditions, we herein independently varied the concentrations of Eosin Y [(EY)], triethanolamine (TEOA), vinyl caprolactam (VC), GelMA precursor, and crosslinking times and assessed the effect of those parameters on the properties the hydrogel. Our data showed that except EY, which exhibited an optimal concentration (~ 0.05 mM), increasing [TEOA], [VA], [GelMA], or crosslinking time improved mechanical (tensile strength/modulus and compressive modulus), adhesion (lap shear strength), swelling, biodegradation properties of the hydrogel. However, increasing the concentrations of crosslinking reagents ([TEOA], [VA], [GelMA]) reduced cell viability in 3-dimensional (3D) cell culture. This study enabled us to optimize the crosslinking conditions to improve the properties of the GelMA hydrogel and to generate a library of hydrogels with defined properties essential for different biomedical applications.

Enzymatic and Chemical Approaches for Post-Polymerization Modifications of Diene Rubbers: Current state and Perspectives

Diene rubbers are polymeric materials which present elastic properties and have double bonds in the macromolecular backbone after the polymerization process. Post-polymerization modifications of rubbers can be conducted by enzymatic or chemical methods. Enzymes are environmentally friendly catalysts and with the increasing demand for rubber waste management, biodegradation and biomodifications have become hot topics of research. Some rubbers are renewable materials and are a source of organic molecules, and biodegradation can be conducted to obtain either oligomers or monomers. On the other hand, chemical modifications of rubbers by click-chemistry are important strategies for the creation and combination of new materials. In a way to expand the scope of uses to other non-traditional applications, several and effective modifications can be conducted with diene rubbers. Two groups of efficient tools, enzymatic, and chemical modifications in diene rubbers, are summarized in this review. By analyzing stereochemical and reactivity aspects, the authors also point to some applications perspectives for biodegradation products and to rational modifications of diene rubbers by combining both methodologies.

Influence of the Silica Specific Surface Area and Ionic Liquids on the Curing Characteristics and Performance of Styrene-Butadiene Rubber Composites

In this work, we present the effect of silica’s specific surface area (180 m²·g⁻¹ and 380 m²·g⁻¹, respectively) on the crosslinking of styrene–butadiene rubber (SBR) composites, as well as their crosslink density and functional properties, such as thermal stability, damping behavior, resistance to thermo-oxidative aging, and tensile properties. Ionic liquids (ILs) with a bromide anion and different cations, i.e., 1-butyl-3-methylimidazolium (Bmi), 1-butyl-3-methylpyrrolidinium (Bmpyr), and 1-butyl-3-methylpiperidinium (Bmpip), were used to enhance the cure characteristics of SBR compounds and the functional properties of SBR vulcanizates. It was proven that apart from the silica’s specific surface area, the filler–polymer and filler–filler physical interactions have a significant impact on the vulcanization kinetics of silica-filled SBR composites. Additionally, the performed studies have shown that ILs positively affected the dispersion of silica’s particles and reduced their ability to form agglomerates in the elastomer matrix, which enhanced the functional properties of the SBR vulcanizates.

Zinc Complexes with 1,3-Diketones as Activators for Sulfur Vulcanization of Styrene-Butadiene Elastomer Filled with Carbon Black

Zinc oxide nanoparticles (N-ZnO) and zinc complexes with 1,3-diketones of different structures were applied instead of microsized zinc oxide (M-ZnO) to activate the sulfur vulcanization of styrene-butadiene rubber (SBR). The influence of vulcanization activators on the cure characteristics of rubber compounds, as well as crosslink density and functional properties of SBR vulcanizates, such as tensile properties, hardness, damping behavior, thermal stability and resistance to thermo-oxidative aging was explored. Applying N-ZnO allowed to reduce the content of zinc by 40% compared to M-ZnO without detrimental influence on the cure characteristic and performance of SBR composites. The activity of zinc complexes in vulcanization seems to strongly depend on their structure, i.e., availability of zinc to react with curatives. The lower the steric hindrance of the substituents and thus the better the availability of zinc ions, the greater was the activity of the zinc complex and consequently the higher the crosslink density of the vulcanizates. Zinc complexes had no detrimental effect on the time and temperature of SBR vulcanization. Despite lower crosslink density, most vulcanizates with zinc complexes demonstrated similar or improved functional properties in comparison with SBR containing M-ZnO. Most importantly, zinc complexes allowed the content of zinc in SBR compounds to be reduced by approximately 90% compared to M-ZnO.

Bio-Based, Flexible, and Tough Material Derived from ε-Poly-l-lysine and Fructose via the Maillard Reaction

We report a bio-based, soft, elastic, and tough material prepared from a mixture of ε-poly-l-lysine (ε-PL) and d-fructose. The obtained complex was insoluble in water, whereas its ingredients had high water solubility. This complex was likely formed via Schiff base formation and subsequent rearrangement reactions, that is, the Maillard reaction, because the reaction occurred between reducing sugars and cationic polyelectrolytes having primary and secondary amino groups. The progress of the Maillard reaction was investigated by proton nuclear magnetic resonance spectroscopy and Fourier transform infrared spectroscopy. Mechanical properties of the complexes were evaluated by tensile testing, and the properties of the optimized complex [ε-PL/fructose = 60:40 (w/w), maximum stress = 27.9 MPa, strain at break = 46%, Young's modulus = 741.6 MPa] resembled those of some petroleum-based plastics. Additionally, the ε-PL/fructose complex displayed antimicrobial activity against Bacillus subtilis. These ε-PL/fructose complexes have biological properties such as antimicrobial activity, low toxicity toward mammals, and biodegradability, which are attributable to the intrinsic nature of ε-PL, as well as enhanced mechanical properties and water resistance compared with pure ε-PL.

Bacterial and enzymatic degradation of poly(cis-1,4-isoprene) rubber: Novel biotechnological applications

Poly(cis-1,4-isoprene) rubber is a highly demanded elastomeric material mainly used for the manufacturing of tires. The end-cycle of rubber-made products is creating serious environmental concern and, therefore, different recycling processes have been proposed. However, the current physical-chemical processes include the use of hazardous chemical solvents, large amounts of energy, and possibly generations of unhealthy micro-plastics. Under this scenario, eco-friendly alternatives are needed and biotechnological rubber treatments are demonstrating huge potential. The cleavage mechanisms and the biochemical pathways for the uptake of poly(cis-1,4-isoprene) rubber have been extensively reported. Likewise, novel bacterial strains able to degrade the polymer have been studied and the involved structural and functional enzymes have been analyzed. Considering the fundamentals, biotechnological approaches have been proposed considering process optimization, cost-effective methods and larger-scale experiments in the search for practical and realistic applications. In this work, the latest research in the rubber biodegradation field is shown and discussed, aiming to analyze the combination of detoxification, devulcanization and polymer-cleavage mechanisms to achieve better degradation yields. The modified superficial structure of rubber materials after biological treatments might be an interesting way to reuse old rubber for re-vulcanization or to find new materials.

Diffusion Behavior of Drug Molecules in Acrylic Pressure-Sensitive Adhesive

Acrylic pressure-sensitive adhesive (PSA) is widely used in transdermal drug delivery systems, while the diffusion behavior of drug molecules in PSA is of great importance. In this paper, PSAs with different cross-link densities were prepared by adjusting the ratio of cross-linkers. The effects of cross-link density and temperature on the diffusion of drugs in PSA were investigated by Fourier transform infrared attenuated total reflectance and molecular dynamics simulation. The consistency between the experimental and simulation results demonstrated that molecular dynamics simulation could be used to predict the diffusion behavior of drugs in PSA. The results showed that free volume and the wriggling of polymer chains are positively related to the diffusion coefficient of drug molecules, while hydrogen bonds hinder drug diffusion.

Influence of Thermally-Accelerated Aging on the Dynamic Mechanical Properties of HTPB Coating and Crosslinking Density-Modified Model for the Payne Effect

Hydroxyl terminated polybutadiene (HTPB) coating is widely used in a solid rocket motor, but an aging phenomenon exists during long-term storage, which causes irreversible damage to the performance of this HTPB coating. In order to study the effect of aging on the dynamic mechanical properties of the HTPB coating, the thermally-accelerated aging test was carried out. The variation of maximum elongation and crosslinking density with aging time was obtained, and a good linear relationship between maximum elongation and crosslinking density was found by correlation analysis. The changing regularity of dynamic mechanical properties with aging time was analyzed. It was found that with the increase of aging time, Tg of HTPB coating increased, Tα, tan β and tan α decreased, and the functional relationships between the loss factor parameters and crosslinking density were constructed. The storage modulus and loss modulus of HTPB coating increased with the increase of aging time, and decreased with the increase of pre-strain. The aging enhanced the Payne effect of HTPB coating, while the pre-strain had a weakening effect. In view of the Payne effect of HTPB coating, the crosslinking density was introduced into Kraus model as aging evaluation parameter, and the crosslinking density modified models with and without pre-strain were established. The proposed models can effectively solve the problem that the Kraus model has a poor fitting effect under the condition of small strain (generally less than 1%) and on the loss modulus, which have improved the correlations between the fitting results and the test results.

Silicone dielectric elastomers optimized by crosslinking pattern – a simple approach to high-performance actuators

Chemical design of silicone elastomers for improving the electromechanical response of dielectric elastomer actuators.

Thermoplastic silicone elastomers based on Gemini ionic crosslinks

Gemini ionic crosslinks produced by neutralization of dicarboxylic and diamino silicones lead in a facile manner to thermoplastic silicone elastomers.

Modification of Ground Tire Rubber—Promising Approach for Development of Green Composites

Ground tire rubber (GTR) was mechano-chemically modified using a road bitumen 100/150 and two types of organic peroxides: di-(2-tert-butyl-peroxyisopropyl)-benzene (BIB) and dicumyl peroxide (DCP). The impact of used additives on reactive sintering efficiency and physico-mechanical properties of modified GTR was investigated using oscillating disc rheometer measurements, followed by tensile tests and swelling behavior studies. It was found that the application of bitumen and both used peroxides (DCP/BIB) improves processing and reactive sintering efficiency better than untreated GTR. However, the results indicate that BIB is more prone to blooming on the surface of modified GTR, thus limiting (especially at higher content) its application as a modifier and promotor of GTR reactive sintering.

Phase behavior of main-chain liquid crystalline polymer networks synthesized by alkyne-azide cycloaddition chemistry

Liquid crystalline polymer networks (LCNs) couple polymer chain organization to molecular ordering, the switching of which has been shown to impart stimuli-responsive properties, including actuation and one-way shape memory, to the networks. While LCNs have long been proposed as artificial muscles, recent reports have also suggested potential as dynamic biomaterial substrates. In contrast to many existing LCNs synthesized using hydrophobic spacers, this work investigates networks synthesized using more hydrophilic spacers to promote interaction with water. A challenge with such materials is liquid crystalline phases could be disrupted in hydrated networks. This work thus investigates the impact of polyether spacers and mesogen composition on the phase behavior of LCNs. Main-chain LCNs were synthesized using alkyne-azide cycloaddition ("click" chemistry), where two different mesogens (5yH and 5yMe) and a non-LC monomer (5yTe) were coupled with one of two different polyether spacers, poly(ethylene glycol) and poly(propylene glycol), and a crosslinker. The chemistry led to high gel fraction materials, the workup of which resulted in networks that displayed no difference in cellular toxicity due to leachable components compared to tissue culture plastic control. Calorimetric analysis, dynamic mechanical analysis, and X-ray scattering revealed the LC microstructure and temperature-responsive properties of the networks. The use of low molecular weight polyether spacers was found to prevent their crystallization within the LC network, and adjusting mesogen composition to enhance its LC phase stability allowed the use of spacers with larger molecular weights and pendant groups. Hydrated networks were found to rearrange their structure compared to dry networks, while maintaining their LC phases. Like other crosslinked LC materials, the networks display shape changes (actuation) that are tied to changes in LC ordering. The result is a new synthetic approach for polydomain networks that form stable LC phases that are tailorable using polyether spacers and may enable future application as hydrated, stimuli-responsive materials.