Oxidation-precipitation of magnetic Fe3O4/AC nanocomposite as a heterogeneous catalyst for electro-Fenton treatment

Improvement of electro-Fenton process by using heterogeneous Fe-MIL-88B nanocatalyst and simultaneous rotation of cathode and anode for dye removal

In this study, improvement of the electro-Fenton process using Fe-MIL-88B along with the innovation in the reactor with the simultaneous rotation of the cathodes and anodes was carried out to remove Acid Blue 25. For this purpose, the Fe-MIL-88B nanocatalyst was synthesised by the thermal solvent method and was characterised by FT-IR, EDAX, XRD, and FESEM. For the experiments, an electrochemical cell with a useful volume of 1 L and rotating cathodes and anodes were used and nanoparticles were added to the system as a slurry. To determine the appropriate values of the effective parameters, the OFAT method was used. According to the results, 0.3 g/L Fe-MIL-88B, pH equal to 3, dye concentration of 75 mg/L, a current intensity of 0.228 A, and a rotation velocity of 100 rpm were chosen as suitable values for the process. In optimal conditions, the dye removal efficiency reached to 92.3% after 90 min, which resulted in a 14.5% improvement in the dye removal efficiency compared to the conventional process under the same conditions. Also, after 90 min, the removal efficiencies of 77.08 and 63.63% were obtained for COD and TOC, respectively. The results indicated acceptable decomposition of the effluent into less hazardous compounds.

Designing novel perlite-Fe3O4@SiO2@8-HQ-5-SA as a promising magnetic nanoadsorbent for competitive adsorption of multicomponent VOCs

Volatile organic compounds (VOCs), which emerge as multicomponent pollutants through many industrial processes, pose a serious threat to human health and the eco-environment due to their volatility, toxicity and dispersion. Hence, the study of competitive adsorption of multicomponent VOCs is of practical and scientific importance. Herein, the perlite-supported Fe3O4@SiO2@8-hydroxyquinoline-5-sulfonic acid (perlite-Fe3O4@SiO2@8-HQ-5-SA) was designed as a novel magnetic nanoadsorbent by a simple strategy and employed for the competitive adsorption of multicomponent toluene, ethylbenzene and xylene in the vapor-phase targeted as VOCs. The successfully prepared perlite-Fe3O4@SiO2@8-HQ-5-SA was characterized by means of SEM, EDX, FT-IR, VSM and BET analyses. Adsorption capacities of 558 mg/g, 680 mg/g and 716 mg/g were achieved for single component toluene, ethylbenzene and xylene, respectively. It was concluded that the adsorption capacities for both binary and ternary components were significantly decreased compared to single component adsorption. The competitive adsorption capacity order of the binary and ternary component VOCs was xylene > ethylbenzene > toluene due to their competitive dominance. The rate-limiting kinetic analysis indicated that the adsorption rates were determined by both the film diffusion and intraparticle diffusion. The analysis of the error metrics demonstrated that the three-parameter isotherm models better described the adsorption data compared to the two-parameter models. In particular, the Toth model provided the closest fit to the experimental equilibrium data. The thermodynamic analysis indicated the spontaneous nature and probability (ΔG° <0), exothermic (ΔH° <0), physical (ΔH° <20 kJ/mol) and a declination in the degree of randomness (ΔS° <0) of the adsorption processes. The reuse efficiency of perlite-Fe3O4@SiO2@8-HQ-5-SA for toluene, ethylbenzene and xylene decreased to only by 88.91%, 88.07% and 87.16% after five recycles. The perlite-Fe3O4@SiO2@8-HQ-5-SA has a significant adsorptive potential compared to other adsorbents reported in the literature, thus it could be recommended as a promising nanoadsorbent for VOCs in industrial processes.

Using a promising biomass-based biochar in photocatalytic degradation: highly impressive performance of RHB/SnO2/Fe3O4 for elimination of AO7

The release of industrial dyes into the environment has recently increased, resulting in harmful effects on people and ecosystems. In recent years, the use of adsorbents in photocatalytic nanocomposites has attracted significant interest due to their low cost, efficiency, and eco-friendly physical and chemical characteristics. Herein, Acid Orange 7 (AO7) removal was investigated by photocatalytic degradation using Rice Rusk Biochar (RHB), Tin (IV) Oxide (SnO₂), and Iron Oxide (Fe₃O₄) as heterogeneous nanocomposite. After the preparation of RHB, the nanocomposite was synthesized and characterized using Field Emission Scanning Electron Microscope (FESEM), X-ray Powder Diffraction (XRD), Brunauer-Emmett-Teller (BET), and Fourier-Transform Infrared Spectroscopy (FT-IR). To optimize the elimination of AO7 by the One-Factor-At-a-Time (OFAT) method, effective parameters including mixing ratio (RHB:SnO₂:Fe₃O₄), dye concentration, solution pH, and nanocomposite dose were studied. The results showed that the removal efficiency of AO7 after 120 min under the optimal mixing ratio of 1:1.5:0.6, dye concentration of 75 mg/l, solution pH of 4, and nanocomposite dose of 0.7 g/l was 92.37%. Moreover, Chemical Oxygen Demand (COD) and Total Organic Carbon (TOC) removal rates were obtained at 82.22 and 72.22%, respectively. The Average Oxidation State (AOS) and Carbon Oxidation State (COS) of the AO7 solution were increased after the process, indicating biodegradability improvement. Various scavenger effects were studied under optimal conditions, and the results revealed that O₂^- and H⁺ reactive species play a crucial role in the photocatalytic degradation of AO7. The reusability and stability of nanocomposite were tested in several consecutive experiments, and the degradation efficiency was reduced from 92 to 79% after five consecutive cycles. It is expected that this research contributes significantly to the utilization of agricultural waste in photocatalytic nanocomposites for the degradation of environmental pollutants.

Fe3O4/Mn3O4/ZnO-rGO hybrid quaternary nano-catalyst for effective treatment of tannery wastewater with the heterogeneous electro-Fenton process: Process optimization

This study investigated chemical oxygen demand (COD) removal from tannery wastewater (TWW) with a novel Fe₃O₄/Mn₃O₄/ZnO-rGO heterogeneous electro Fenton (HEF) hybrid magnetically-separable nano-catalyst. The graphite cathode and Ti/IrO₂/RuO₂ anode were used in the HEF process. With aeration (2 L/min), in-situ H₂O₂ generation occurred. The nano-catalyst was characterized by XRD, XPS, DLS, FT-IR, ζ potential, SEM, TEM, and BET techniques in detail. The system was modelled with a central composite design and optimized numerically. The established model was adequate, valid, reliable, and reproducible to predict the COD removal efficiency. OH and O₂^- were the oxidative species responsible for organic matter degradation. The effect of different processes was investigated, and efficiency was ranked from high to low as; HEF > anodic oxidation-H₂O₂ > anodic oxidation > adsorption. Under the optimum conditions; pH: 3.5, current density: 7.37 mA/cm², reaction time: 79.43 min, and catalyst dose: 0.06 g/L, COD removal efficiency reached a maximum of 97.08%. The energy consumption and cost to remove 1 kg COD were 10.87 kWh and $1.41. The degradation of COD fitted the pseudo-first-order model. The nano-catalyst was stable and reusable with a minimum yield of 78.12% after 5 cycles.

Delafossite-alumina nanocomposite for enhanced catalytic wet peroxide oxidation of anionic pollutants

Mass transfer efficiency and catalytic reactivity are the two major hurdles for heterogeneous catalytic wet peroxide oxidation (CWPO) technologies. To address these issues, nanocomposite CuFeO₂/Al₂O₃ was synthesized and assessed as a novel catalyst for enhanced adsorption and oxidation of anionic pollutants (catechol and reactive red 195 (RR195)) in waters. With a positive charge on the nanocomposite by introducing Al₂O₃, the adsorption of anionic pollutants was promoted. The surface complexation reaction on CuFeO₂/Al₂O₃, which fits well to the Langmuir isotherm, has engined the mass transfer of pollutants to the nanocatalyst that demonstrated 96.46% and 99.75% removal of catechol and RR195 at pH 3, respectively. CuFeO₂/Al₂O₃ also showed good performance in various reaction media including binary pollutants system and real wastewaters. The hydroxyl radical in aqueous solution played a major role in the pollutants degradation. The CWPO, which followed the Haber-Weiss mechanism, has been accelerated by the Cu and Fe redox cycles. The robustness of the catalyst was verified by negligible amount of metal leaching from the catalysts along with stable catalytic performance after five cycles. Upon the observed results, CuFeO₂/Al₂O₃ with the synergistic effect has shown to be a promising catalyst for removal and degradation of anionic pollutants in CWPO.

A novel bio-electro-Fenton process for eliminating sodium dodecyl sulphate from wastewater using dual chamber microbial fuel cell

The frequent occurrence of surfactants in urban wastewaters represents a multifaceted environmental concern. In this investigation, bio-electro-Fenton-microbial fuel cell (BEF-MFC) was developed for the degradation of sodium dodecyl sulphate (SDS) from wastewater. The synthesised cathode catalyst (powdered activated carbon and iron oxide) facilitated the Fenton reaction in the cathodic chamber of the MFC, concurrently generating a maximum power density of 105.67 mW m^-2. The overall performance of the BEF-MFC for SDS removal and power generation excelled the control MFC (C-MFC) having carbon black coated cathode under similar operating conditions. Although, the rate of SDS degradation was favourable in acidic pH, under neutral pH, 70.8 ± 6.4% of SDS degradation was achieved in 120 min in BEF-MFC. A comparison of environmental impacts of BEF-MFC with up-flow MFC and electrochemical oxidation using life cycle assessment tool suggests that BEF-MFC can be one of the promising technologies for the tertiary treatment of wastewater.

The electro-Fenton regeneration of Granular Activated Carbons: Degradation of organic contaminants and the relationship to the carbon surface

Electrochemical regeneration of Granular Activated Carbon is an emerging treatment option to restore adsorption capacity in systems designed to remove organic contaminants from aqueous solutions. The electro-Fenton process is one such electrochemical process and it is reviewed along with other members of its family including Photoelectro-Fenton and Heterogeneous electro-Fenton and electro-Fenton like reactions, for its ability to regenerate Granular Activated Carbons contaminated with organics. The behaviour of critical operating parameter such as pH, current, catalyst concentration and initial contaminant concentration are reviewed to find optimal operating conditions. The relationship between electro-Fenton regeneration and the chemical and physical surface of the carbon is also explored. Understanding regeneration mechanisms and the optimal operating conditions enables these technologies to be used commercially and to be scaled-up and treat contaminated waters more efficiently.

Engineered FeVO4/CeO2 nanocomposite as a two-way superior electro-Fenton catalyst for model and real wastewater treatment

FeVO₄/CeO₂ was applied in the electro-Fenton (EF) degradation of Methyl Orange (MO) as a model of wastewater pollution. The results of the characterization techniques indicate that FeVO₄ with triclinic structure and face-centered cubic fluorite CeO₂ maintained their structures during the nanocomposite synthesis. The effect of applied current intensity, initial pollutant concentration, initial pH, and catalyst weight was investigated. The MO removal reached 96.31% and chemical oxygen demand (COD) removal 70% for 60 min of the reaction. The presence of CeO₂ in the nanocomposite plays a key role in H₂O₂ electro-generation as a significant factor in the electro-Fenton (EF) system. The metal leaching from FeVO₄/CeO₂ was negligible (cerium 4.1%, iron 4.3%, and vanadium 1.7%), which indicates that the active species in the nanocomposite are strongly interacting with each other and are stable. The performance of the nanocatalyst in real wastewaters, salty, and binary systems was acceptable and the pollutions were removed efficiently. The synergistic effect between V, Fe, and Ce could be account as the reason for the respectable function of FeVO₄/CeO₂. The electron transfer proceeds via Haber-Weiss mechanism. A degradation pathway was proposed through by-products analysis using gas chromatography-mass spectrometry (GC-MS) technique. The pseudo-first-order kinetic model described the obtained experimental results (R² = 0.9906). The electro-Fenton system efficiency was improved by adding persulfate. The nanocomposite preserved almost its efficiency after six cycles. The obtained results demonstrate that the synergistic catalyst (FeVO₄/CeO₂) has the capability to introduce as a promising replacement of conventional catalysts in the electro-Fenton processes with brilliant proficiency.