Reusable poly(allylamine)-based solid materials for carbon dioxide capture under continuous flow of ambient air

Development and Characterization of Polyethylenimine-Infiltrated Mesoporous Silica Foam Pellets for CO2 Capture

Polyethylenimine (PEI) has been shown to be promising for direct air capture (DAC) of carbon dioxide and has potential for commercial scale-up globally. Laboratory scale processes include multiple steps, such as mixing, solvent extraction, vacuum application, sonication, and various flushes and activation steps. It is critical to properly control these operating parameters to achieve higher capture capacity as a result of the optimized material configuration. This study adopts previously published pelletization processes for PEI-infiltrated mesoporous foam silica (mesoporous silica foam) to uncover the adsorption mechanisms and optimize the associated fabrication steps, such as sonication, to achieve higher sorbent productivity. A high capture capacity was achieved at 46 °C for 75 wt % PEI loading (2.27 mmol/g) followed by PEI_MSF 70 (1.81 mmol/g) and PEI_MSF 80 (1.44 mmol/g). As part of the optimization, sonication parameters of frequency, amplitude, and time were modified for PEI_MSF 75 sorbent, which resulted in the highest uptake capacity of 3.04 mmol/g (sonicated at 40 kHz and a wave amplitude of 50% for 30 s). These preliminary results would tend to prove that sonication energy affects carbon capture capacity, although there is still a lack of understanding regarding the exact underlying mechanism, suggesting the need for further investigation. It is important to note that the present work is focused on the adsorption mechanisms and not desorption or durability of the capture performance. Ongoing research addresses these factors. This paper is intended to establish baseline DAC behavior of a promising capture medium and begins probing the optimization spectrum by considering the effects of sonication energy on adsorption. Ongoing work intends to address potential abbreviations of the full range of process steps and furthers the understanding of kinetics by considering the desorption and resorption attributes.

Support Pore Structure and Composition Strongly Influence the Direct Air Capture of CO2 on Supported Amines

A variety of amine-impregnated porous solid sorbents for direct air capture (DAC) of CO2 have been developed, yet the effect of amine-solid support interactions on the CO2 adsorption behavior is still poorly understood. When tetraethylenepentamine (TEPA) is impregnated on two different supports, commercial γ-Al2O3 and MIL-101(Cr), they show different trends in CO2 sorption when the temperature (-20 to 25 °C) and humidity (0-70% RH) of the simulated air stream are varied. In situ IR spectroscopy is used to probe the mechanism of CO2 sorption on the two supported amine materials, with weak chemisorption (formation of carbamic acid) being the dominant pathway over MIL-101(Cr)-supported TEPA and strong chemisorption (formation of carbamate) occurring over γ-Al2O3-supported TEPA. Formation of both carbamic acid and carbamate species is enhanced over the supported TEPA materials under humid conditions, with the most significant enhancement observed at -20 °C. However, while equilibrium H2O sorption is high at cold temperatures (e.g., -20 °C), the effect of humidity on a practical cyclic DAC process is expected to be minimal due to slow H2O uptake kinetics. This work suggests that the CO2 capture mechanisms of impregnated amines can be controlled by adjusting the degree of amine-solid support interaction and that H2O adsorption behavior is strongly affected by the properties of the support materials. Thus, proper selection of solid support materials for amine impregnation will be important for achieving optimized DAC performance under varied deployment conditions, such as cold (e.g., -20 °C) or ambient temperature (e.g., 25 °C) operations.

Characteristics, application and modeling of solid amine adsorbents for CO2 capture: A review

In recent years, global warming has become an important topic of public concern. As one of the most promising carbon capture technologies, solid amine adsorbents have received a lot of attention because of their high adsorption capacity, excellent selectivity, and low energy cost, which is committed to sustainable development. The preparation methods and support materials can influence the thermal stability and adsorption capacity of solid amine adsorbents. As a supporting material, it needs to meet the requirements of high pore volume and abundant hydroxyl groups. Industrial and biomass waste are expected to be a novel and cheap raw material source, contributing both carbon dioxide capture and waste recycling. The applied range of solid amine adsorbents has been widened from flue gas to biogas and ambient air, which require different research focuses, including strengthening the selectivity of CO₂ to CH₄ or separating CO₂ under the condition of the dilute concentration. Several kinetic or isotherm models have been adopted to describe the adsorption process of solid amine adsorbents, which select the pseudo-first order model, pseudo-second order model, and Langmuir isotherm model most commonly. Besides searching for novel materials from solid waste and widening the applicable gases, developing the dynamic adsorption and three-dimensional models can also be a promising direction to accelerate the development of this technology. The review has combed through the recent development and covered the shortages of previous review papers, expected to promote the industrial application of solid amine adsorbents.

Recent advances in direct air capture by adsorption

Significant progress has been made in direct air capture (DAC) in recent years. Evidence suggests that the large-scale deployment of DAC by adsorption would be technically feasible for gigatons of CO₂ capture annually. However, great efforts in adsorption-based DAC technologies are still required. This review provides an exhaustive description of materials development, adsorbent shaping, in situ characterization, adsorption mechanism simulation, process design, system integration, and techno-economic analysis of adsorption-based DAC over the past five years; and in terms of adsorbent development, affordable DAC adsorbents such as amine-containing porous materials with large CO₂ adsorption capacities, fast kinetics, high selectivity, and long-term stability under ultra-low CO₂ concentration and humid conditions. It is also critically important to develop efficient DAC adsorptive processes. Research and development in structured adsorbents that operate at low-temperature with excellent CO₂ adsorption capacities and kinetics, novel gas-solid contactors with low heat and mass transfer resistances, and energy-efficient regeneration methods using heat, vacuum, and steam purge is needed to commercialize adsorption-based DAC. The synergy between DAC and carbon capture technologies for point sources can help in mitigating climate change effects in the long-term. Further investigations into DAC applications in the aviation, agriculture, energy, and chemical industries are required as well. This work benefits researchers concerned about global energy and environmental issues, and delivers perspective views for further deployment of negative-emission technologies.

Understanding the Effect of Water on CO2 Adsorption

Carbon capture from large sources and ambient air is one of the most promising strategies to curb the deleterious effect of greenhouse gases. Among different technologies, CO₂ adsorption has drawn widespread attention mostly because of its low energy requirements. Considering that water vapor is a ubiquitous component in air and almost all CO₂-rich industrial gas streams, understanding its impact on CO₂ adsorption is of critical importance. Owing to the large diversity of adsorbents, water plays many different roles from a severe inhibitor of CO₂ adsorption to an excellent promoter. Water may also increase the rate of CO₂ capture or have the opposite effect. In the presence of amine-containing adsorbents, water is even necessary for their long-term stability. The current contribution is a comprehensive review of the effects of water whether in the gas feed or as adsorbent moisture on CO₂ adsorption. For convenience, we discuss the effect of water vapor on CO₂ adsorption over four broadly defined groups of materials separately, namely (i) physical adsorbents, including carbons, zeolites and MOFs, (ii) amine-functionalized adsorbents, and (iii) reactive adsorbents, including metal carbonates and oxides. For each category, the effects of humidity level on CO₂ uptake, selectivity, and adsorption kinetics under different operational conditions are discussed. Whenever possible, findings from different sources are compared, paying particular attention to both similarities and inconsistencies. For completeness, the effect of water on membrane CO₂ separation is also discussed, albeit briefly.

Rational Design of Polyamine-Based Cryogels for Metal Ion Sorption

Here we report the method of fabrication of supermacroporous monolith sorbents (cryogels) via covalent cross-linking of polyallylamine (PAA) with diglycidyl ether of 1,4-butandiol. Using comparative analysis of the permeability and sorption performance of the obtained PAA cryogels and earlier developed polyethyleneimine (PEI) cryogels, we have demonstrated the advantages and disadvantages of these polymers as sorbents of heavy metal ions (Cu(II), Zn(II), Cd(II), and Ni(II)) in fixed-bed applications and as supermacroporous matrices for the fabrication of composite cryogels containing copper ferrocyanide (CuFCN) for cesium ion sorption. Applying the rate constant distribution (RCD) model to the kinetic curves of Cu(II) ion sorption on PAA and PEI cryogels, we have elucidated the difference in sorption/desorption rates and affinity constants of these materials and showed that physical sorption contributed to the Cu(II) uptake by PAA, but not to that by PEI cryogels. It was shown that PAA cryogels had significantly higher selectivity for Cu(II) sorption in the presence of Zn(II) and Cd(II) ions in comparison with that of PEI cryogels, while irreversible sorption of Co(II) ions by PEI can be used for the separation of Ni(II) and Co(II) ions. Using IR and Mössbauer spectroscopy, we have demonstrated that strong complexation of Cu(II) ions with PEI significantly affects the in situ formation of Cu(II) ferrocyanide nanosorbents leading to their inefficiency for Cs⁺ ions selective uptake, whereas PAA cryogel was applicable for the fabrication of efficient monolith composites via the in situ formation of CuFCN or loading of ex situ formed CuFCN colloids.

Effect of Extended Aging and Oxidation on Linear Poly(propylenimine)-Mesoporous Silica Composites for CO2 Capture from Simulated Air and Flue Gas Streams

Physical aging or degradation of amine-containing polymers and supported amine adsorbents is a critical issue that could limit the practical application of such materials for CO₂ capture. However, to date, there is a scarcity of studies that evaluate the long-term stability of amine-based sorbents without the exclusive use of accelerated aging tests. Here, we demonstrate that extended aging (∼2 years) of linear poly(propylenimine) (LPPI) confined in mesoporous silica (SBA-15) supports does not drastically impact the CO₂ adsorption performance under simulated flue gas (10% CO₂) and direct air capture (DAC, 400 ppm CO₂) conditions, although the behavior of the aged sorbents and polymers in the two CO₂ concentration regimes differs. The sorbents made with aged LPPI have modestly decreased CO₂ uptake performance (≲20% lower) compared to the fresh polymers, with overall good CO₂ cycling performance. The data indicate that only slow degradation occurs under the deployed ambient storage conditions. Even after extended aging, the LPPI-based sorbents preserved their ability to display stable temperature-swing cycling performance. In parallel, the impact of blending LPPI polymers of different number-average molecular weights, M_n, is evaluated, seeking to understand its impact on adsorbent performance. The results demonstrate that the blends of two M_n aged LPPI give similar CO₂ adsorption performance to adsorbents made from a single-M_n LPPI, suggesting that molecular weight will not negatively impact adsorbent performance in the studied M_n range. After an accelerated oxidation experiment, the aged LPPI sorbents retained a larger portion of the samples' original performance when cycling under simulated flue gas conditions than under DAC conditions. However, in each case, the oxidized sorbents could be cycled repeatedly with consistent uptake performance. Overall, these first of their kind extended aging tests suggest that LPPI-based amine adsorbents offer promise for long-term, stable use in carbon capture applications.

Stability of amine-functionalized CO2 adsorbents: a multifaceted puzzle

This review focuses on important stability issues facing amine-functionalized CO2 adsorbents, including amine-grafted and amine-impregnated silicas, zeolites, metal-organic frameworks and carbons. During the past couple of decades, major advances were achieved in understanding and improving the performance of such materials, particularly in terms of CO2 adsorptive properties such as adsorption capacity, selectivity and kinetics. Nonetheless, to pave the way toward commercialization of adsorption-based CO2 capture technologies, in addition to other attributes, adsorbent materials should be stable over many thousands of adsorption-desorption cycles. Adsorbent stability, which is of utmost importance as it determines adsorbent lifetime and operational costs of CO2 capture, is a multifaceted issue involving thermal, hydrothermal, and chemical stability. Here we discuss the impact of the adsorbent physical and chemical properties, the feed gas composition and characteristics, and the adsorption-desorption operational parameters on the long-term stability of amine-functionalized CO2 adsorbents. We also review important insights associated with the underlying deactivation pathways of the adsorbents upon exposure to high temperature, oxygen, dry CO2, sulfur-containing compounds, nitrogen oxides, oxygen and steam. Finally, specific recommendations are provided to address outstanding stability issues.