Distribution of heavy metals from iron bath-melting separation process applied to municipal solid waste incineration fly ash

Municipal solid waste (MSW) incineration fly ash as an important source of heavy metal pollution in China

Incineration has overtaken landfilling as the most important option for disposal of the increasing volumes of municipal solid waste (MSW) generated in China. Accordingly, disposal of the incineration fly ash, which is enriched with a range of heavy metals, has become a key challenge for the industry. This review analyzes the temporal and spatial trends in the distributions of As, Cd, Cr, Cu, Ni, Pb, Zn, and Hg in MSW incineration fly ash between 2003 and 2017, and estimates the inventories of heavy metals associated with the fly ash and the average levels of heavy metals in Chinese MSW based on their mass flow during MSW incineration. It was estimated that MSW incinerators in China released approximately 1.12 × 10², 2.96 × 10³, 1.82 × 10², 3.64 × 10⁴, 1.00 × 10², 7.32 × 10³, 2.42 × 10², and 1.47 × 10¹ tonnes of Cd, Pb, Cr, Zn, Ni, Cu, As, and Hg, respectively, with the fly ash in 2016. Due to the much greater fly ash generation rate, the incinerators based on circulating fluidized bed combustor (CFBC) technology released more heavy metals during incineration of MSW compared to those based on grate furnace combustor (GFC) technology. Results of mass-flow modeling indicate that the geometric mean contents of Cd, Pb, Cr, Zn, Ni, Cu, As, and Hg in Chinese MSW were 3.0, 109, 101, 877, 34, 241, 21, and 1.7 mg/kg, respectively, which are comparable to those in the MSW from other countries. To protect the environment from the significant potential ecological risk posed by heavy metals in the mismanaged fly ash, strict regulation enforcement and compliance monitoring are necessary to reduce the heavy metal pollution brought by improper disposal of MSW incineration fly ash, and more research and development efforts on advanced technologies for stabilization of heavy metals in fly ash and its environmentally sound reuse can help mitigate its environmental risk.

Behaviour mechanisms and correlation between lead (Pb) and its isotope (210)Pb in industrial residue as an indicator for waste characterization

Total lead and (210)Pb concentrations were determined in various ash fractions (collected from two of the world's largest oil shale-fired power plants) by inductively coupled plasma mass-spectrometry (ICP-MS) and gamma spectrometry. Results show a clear increase in total lead (values up to 193 ppm in filter ashes) and (210)Pb (values up to 148 Bq kg(-1) in filter ashes) concentrations in the ash fractions from the furnace towards the filter ashes. A strong positive linear correlation (Pearson's bivariate correlation remained between 0.86 and 0.99) was determined between total lead concentration (ppm) and (210)Pb activity concentration (Bq kg(-1)) within all the boilers under observation. The constant concentration ratio between total lead and (210)Pb remained around one (with minor exceptions), independent of the sampling location and the used combustion technology. The determined concentration ratio can be applicable as an indicative tool in waste material characterization. It also provides multiple additions to the general material characterization approach, by integrating radiological and elemental studies and providing an option to rapidly obtain initial indicative information about the residues. This in turn helps to generate the initial information to work out the next steps in waste material management.

Trip time model for municipal solid waste collection applicable to developing countries

Municipal authorities in developing countries are faced with how to effectively and efficiently collect solid wastes from service points to disposal sites. Options for economy of time and improvement in the efficiency of collection operation can best be evaluated by conducting a time and motion study on an existing system. This study presents the development of a simulation model that calculates the time required to accomplish a solid waste collection trip. In order to determine a collection trip time, the collection operation was separated into units and the time required to perform each of these unit operations was simulated from field data. Results from the studied collection vehicle showed that the average pickup time was 1.68 minutes/trip, the average drop-down rate was 1.8 minutes/trip, and the average at-site time was 1.38 minutes/trip. The average time spent at intersections and turns was approximately 0.38 minutes and 0.18 minutes respectively. The haul time to the disposal site represented 0.034 of the travel distance to the disposal site, while the haul time from the disposal site represented 0.030 of the travel distance from the disposal site. When the model was applied to municipal solid waste collection in Ilorin, Nigeria, the estimated trip times were approximately 84% of the observed trip times. The estimated trip times by the model can find practical application as a decision support tool for municipal solid waste managers in areas of trip assignments, route design, logistics management and costs and emission reduction strategies.

Investigation into the artificial ageing effects on the microstructure of an industrial solid waste treated with cement

Metal hydroxide sludges are classified as hazardous wastes in the European Hazardous Waste Catalogue (EHWC) because of their high heavy metal contents (Zn, Cr, Fe, Cu, etc.) and the release of these pollutants to the environment. Thereby, the disposal of this waste without any treatment is a substantial environmental problem. Stabilization/solidification technologies are widely used for the treatment of wastes and residues in order to obtain inert materials. This work aims to assess the effectiveness of the chemical fixation and solidification of a metal hydroxide sludge generated by the electrotyping surface treatment industry, using Portland Artificial Cement. In order to predict the medium- and long-term behaviour of the solidified waste, an artificial ageing by means of thermal shocks and humidity variation cycles was applied. Scanning Electron Microscopy (SEM) and X-ray Diffraction studies revealed a considerable increase in calcite within the solid matrix after the artificial ageing, which can be attributed to the phenomenon of carbonation. It was also found that the mechanical properties of the solidified material, after ageing, were improved by up to 30%.