Spatial analysis of volatile organic compounds in South Philadelphia using passive samplers

Evaluation of selected solid adsorbents for passive sampling of atmospheric oil and natural gas non-methane hydrocarbons

This project investigated passive adsorbent sampling of light (C₂-C₅) hydrocarbons which are sensitive tracers of fugitive emissions from oil and natural gas (O&NG) sources. Stronger adsorbent materials, i.e. Carboxen 1000 and Carboxen 1016, than those typically used in adsorbent sampling were considered. Experiments were conducted in laboratory and field settings using thermal desorption - gas chromatography analysis. Uptake of water vapor and system blanks were challenges inherent to the increased affinity of these adsorbents. Carboxen 1000 exhibited the best signal-to-noise ratio for the target compounds after optimizing conditioning parameters to reduce blanks, and by reducing the adsorbent mass loaded in the cartridge. This strategy reduced blanks to equivalent ambient air mole fractions of <0.05 nmol mol^-1 (ppb), and allowed determination of these O&NG tracers over three-day sampling intervals with a lower detection limit of ≥0.5-1 ppb. Linear VOCs uptake was observed in dry air. Water uptake was as high as 0.65 g_H2O g^-1_adsorbent at relative humidity (RH) above ≈ 75%. The water collection passivates adsorbent sites and competes with the uptake rates of VOCs; under the worst case relative humidity level of 95% RH, VOCs uptake rates dropped to 27-39% of those in dry air. This effect potentially causes results to be biased low when cartridges are deployed at high relative humidity (RH), including overnight, when RH is often elevated over daytime levels. Nonetheless, representative sampling results were obtained under ambient conditions during three field studies where cartridges were evaluated alongside whole air sample collection in canisters. Agreement varied by compound: Ethane and alkenes correlated poorly and could not be analyzed with satisfactory results; results for C₃-C₅ alkanes were much better: i-butane correlated with R² > 0.5, and propane, n-butane, i-pentane, and n-pentane with R² > 0.75, which demonstrates the feasibility of the passive sampling of these latter O&NG tracers. Implications: Oil and natural gas development has been associated with emissions of petroleum hydrocarbons that impact air quality and human health. This research characterizes and defines the application possibilities of solid adsorbent sampling for atmospheric passive sampling monitoring of low molecular weight volatile organic compounds (i.e. ethane through pentane isomers) that are most commonly emitted from natural gas drilling and well sites. The passive sampling of these pollutants offers a simple, low cost, and readily applicable monitoring method for assessing emissions and air quality impacts in the surroundings of oil and gas operations.

Using Gas-Phase Air Quality Sensors to Disentangle Potential Sources in a Los Angeles Neighborhood

In the late summer of 2016, our team deployed a network of low-cost air quality sensing systems in partnership with community-based organizations in a neighborhood in South Los Angeles, California. Residents of this community were concerned about possible emissions from local oil and gas activity, however in addition to these potential emissions, the neighborhood is also subject to a complex mixture of pollutants from other nearby sources including major highways. For this deployment, metal-oxide VOC sensors were quantified to provide methane (CH₄) and total non-methane hydrocarbon (TNMHCs) concentration estimates. This data along with other sensor signals, meteorological data, and community member observations was used to examine the composition and possible origins of observed emissions. The sensor network displayed expected environmental trends and highlighted short-term elevations in CH₄ and/or TNMHCs, which we were then able to investigate more closely. The results indicated that sources of both combusted and volatilized hydrocarbons were likely affecting air quality throughout the community, including near the site of the local oil and gas activity. This deployment may serve as a model for how multi-sensor systems deployed in networks can be leveraged to better understand sources in complex areas, potentially supporting future community-based air quality research.

Spatial analysis of volatile organic compounds using passive samplers in the Rubbertown industrial area of Louisville, Kentucky, USA

Select volatile organic compounds (VOCs) were measured in the vicinity of chemical facilities and other operations in the Rubbertown industrial area of Louisville, Kentucky (USA) using modified EPA Methods 325A/B passive sampler tubes. Two-week, time-integrated passive samplers were deployed at ten sites which were aggregated into three site groups of varying distances from the Rubbertown area facilities. In comparison to canister data from 2001 to 2005, two of the sites suggested generally lower current VOC levels. Good precision was obtained from the duplicate tubes (≤ 12%) for benzene, toluene, ethylbenzene, and xylene isomers (BTEX), styrene, 1,3-butadiene, perchloroethylene, and other trace VOCs. BTEX, styrene, and 1,3-butadiene concentrations were statistically significantly higher at two site groups near Rubbertown sources than the site group farther away. As found in a similar study in South Philadelphia, BTEX concentrations were also lower for sites farther from a source, though the decline was less pronounced on a percentage basis in Rubbertown. These results suggest that EPA Methods 325A/B can be useful to assess VOC gradients for emissions from chemical facilities besides fenceline benzene levels from refineries.

Rubbertown Next Generation Emissions Measurement Demonstration Project

Industrial facilities and other sources can emit air pollutants from fugitive leaks, process malfunctions and area sources that can be difficult to understand and to manage. Next generation emissions measurement (NGEM) approaches executed near facilities are enabling new ways to assess these sources and their impacts to nearby populations. This paper describes complementary uses of emerging NGEM systems in a Louisville, KY industrial district (Rubbertown), focusing on an important area air toxic, 1,3-butadiene. Over a one-year deployment starting in September 2017, two-week average passive samplers (PSs) at 11 sites showed both geospatial and temporal trends. At 0.24 ppbv annual average 1,3-butadiene concentration, a group of PSs located near facility fence lines was elevated compared to a PS group located in the community and upwind from facilities (0.07 ppbv average). Two elevated PS periods capturing emission events were examined using time-resolved NGEM approaches as case studies. In one event a 1.18 ppbv PS reading was found to be relatively localized and was caused by a multiday emission from a yet to be identified, non-facility source. In the other event, the airshed was more broadly impacted with PS concentrations ranging from 0.71 ppbv for the near-facility group to 0.46 ppbv for the community group. This case was likely influenced by a known emission event at an industrial facility. For both case studies, air pollutant and wind data from prototype NGEM systems were combined with source location models to inform the emission events. This research illustrates the power of applying NGEM approaches to improve both the understanding of emissions near sources and knowledge of impacts to near-source communities.

Evaluation of a Passive Sampling Method for Long-Term Continuous Monitoring of Volatile Organic Compounds in Urban Environments

Environmental Protection Agency Method 325 was developed for continuous passive monitoring of volatile organic compounds (VOCs), particularly benzene, at petroleum refinery fencelines. In this work, a modified version of the method was evaluated at an Ontario near-road research station in winter to assess its suitability for urban air quality monitoring. Samples were collected at 24 hour and 14 day resolution to investigate accuracy for different exposure times. Tubes were analyzed by thermal desorption-gas chromatography-mass spectrometry, and 11 VOCs were quantified, including aromatic air toxics. The same VOCs were simultaneously monitored using traditional canister sampling for comparison, and a subset of four were also monitored using a novel miniature gas chromatograph. Good agreement (within 10%) was observed between the 14 day passive tube samples and the canister samples for benzene. However, field-calibrated uptake rates were required to correct passive tube concentrations for less volatile aromatics. Passive tube deployment and analysis is inexpensive; sampling does not require power, and accurate measurements of benzene are demonstrated here for an urban environment. The method is expected to be advantageous for the generation of long-term continuous benzene datasets suitable for epidemiological research with greater spatial coverage than is currently available using traditional monitoring techniques.

Application of passive sorbent tube and canister samplers for volatile organic compounds at refinery fenceline locations in Whiting, Indiana

Select volatile organic compounds (VOCs) in ambient air were measured at four fenceline sites at a petroleum refinery in Whiting, IN, using modified EPA Method 325 A/B with passive tubes and EPA Compendium Method TO-15 with canister samplers. One-week, time-integrated samplers were deployed for 8 weeks with tubes and canister samplers deployed in duplicate. Good precision was obtained from the duplicate tubes (<7%) and duplicate canisters (≤10%) for BTEX, perchloroethylene, and styrene. The tubes yielded statistically significantly higher concentrations than canisters for benzene, toluene, ethylbenzene, and m,p-xylene. However, all differences were estimated to be <0.1 ppbv. No concentration differences among the four Whiting sites were found for any of the VOCs.

IMPLICATIONS

Recently enacted EPA Methods 325A/B use passive-diffusive tube samplers to measure benzene at refinery fenceline locations. This pilot study presents VOC data applying a modified version of EPA Method 325 A/B and its comparison to EPA Compendium Method TO-15 canister samplers at four refinery fenceline sites. The findings from this study provide additional confidence in application of the tube method at refineries to ascertain VOC source influence since tube and canister samplers were comparable and good precision was obtained from duplicate sampling for both methods. No overall difference in these reported VOC concentrations was found between Whiting sites for tubes or canisters.

Sample integrity evaluation and EPA method 325B interlaboratory comparison for select volatile organic compounds collected diffusively on Carbopack X sorbent tubes

A sample integrity evaluation and an interlaboratory comparison were conducted in application of U.S. Environmental Protection Agency (EPA) Methods 325A and 325B for diffusively monitoring benzene and other selected volatile organic compounds (VOCs) using Carbopack X sorbent tubes. To evaluate sample integrity, VOC samples were refrigerated for up to 240 days and analyzed using thermal desorption/gas chromatography-mass spectrometry at the EPA Office of Research and Development laboratory in Research Triangle Park, NC, USA. For the interlaboratory comparison, three commercial analytical laboratories were asked to follow Method 325B when analyzing samples of VOCs that were collected in field and laboratory settings for EPA studies. Overall results indicate that the selected VOCs collected diffusively on sorbent tubes generally were stable for 6 months or longer when samples were refrigerated. This suggests the specified maximum 30-day storage time of VOCs collected diffusively on Carbopack X passive samplers and analyzed using Method 325B might be able to be relaxed. Interlaboratory comparison results were in agreement for the challenge samples collected diffusively in an exposure chamber in the laboratory, with most measurements within ±25% of the theoretical concentration. Statistically significant differences among laboratories for ambient challenge samples were small, less than 1 part per billion by volume (ppbv). Results from all laboratories exhibited good precision and generally agreed well with each other.

South Philadelphia passive sampler and sensor study

From June 2013 to March 2015, in total 41 passive sampler deployments of 2 wk duration each were conducted at 17 sites in South Philadelphia, PA, with results for benzene discussed here. Complementary time-resolved measurements with lower cost prototype fenceline sensors and an open-path ultraviolet differential optical absorption spectrometer were also conducted. Minimum passive sampler benzene concentrations for each sampling period ranged from 0.08 ppbv to 0.65 ppbv, with a mean of 0.25 ppbv, and were negatively correlated with ambient temperature (-0.01 ppbv/°C, R(2) = 0.68). Co-deployed duplicate passive sampler pairs (N = 609) demonstrated good precision with an average and maximum percent difference of 1.5% and 34%, respectively. A group of passive samplers located within 50 m of a refinery fenceline had a study mean benzene concentration of 1.22 ppbv, whereas a group of samplers located in communities >1 km distant from facilities had a mean of 0.29 ppbv. The difference in the means of these groups was statistically significant at the 95% confidence level (p < 0.001). A decreasing gradient in benzene concentrations moving away from the facilities was observed, as was a significant period-to-period variation. The highest recorded 2-wk average benzene concentration for the fenceline group was 3.11 ppbv. During this period, time-resolved data from the prototype sensors and the open-path spectrometer detected a benzene signal from the west on one day in particular, with the highest 5-min path-averaged benzene concentration measured at 24 ppbv.

IMPLICATIONS

Using a variation of EPA's passive sampler refinery fenceline monitoring method, coupled with time-resolved measurements, a multiyear study in South Philadelphia informed benzene concentrations near facilities and in communities. The combination of measurement strategies can assist facilities in identification and mitigation of emissions from fugitive sources and improve information on air quality complex air sheds.

Volatile organic compounds at two oil and natural gas production well pads in Colorado and Texas using passive samplers

A pilot study was conducted in application of the U.S. Environmental Protection Agency (EPA) Methods 325A/B variant for monitoring volatile organic compounds (VOCs) near two oil and natural gas (ONG) production well pads in the Texas Barnett Shale formation and Colorado Denver-Julesburg Basin (DJB), along with a traffic-dominated site in downtown Denver, CO. As indicated in the EPA method, VOC concentrations were measured for 14-day sampling periods using passive-diffusive tube samplers with Carbopack X sorbent at fenceline perimeter and other locations. VOCs were significantly higher at the DJB well pad versus the Barnett well pad and were likely due to higher production levels at the DJB well pad during the study. Benzene and toluene were significantly higher at the DJB well pad versus downtown Denver. Except for perchloroethylene, VOCs measured at passive sampler locations (PSs) along the perimeter of the Barnett well pad were significantly higher than PSs farther away. At the DJB well pad, most VOC concentrations, except perchloroethylene, were significantly higher prior to operational changes than after these changes were made. Though limited, the results suggest passive samplers are precise (duplicate precision usually ≤10%) and that they can be useful to assess spatial gradients and operational conditions at well pad locations over time-integrated periods.

IMPLICATIONS

Recently enacted EPA Methods 325A/B use passive-diffusive tube samplers to measure benzene at multiple fenceline locations at petrochemical refineries. This pilot study presents initial data demonstrating the utility of Methods 325A/B for monitoring at ONG facilities. Measurements revealed elevated concentrations reflective of production levels and spatial gradients of VOCs relative to source proximity at the Barnett well pad, as well as operational changes at the DJB well pad. Though limited, these findings indicate that Methods 325A/B can be useful in application to characterize VOCs at well pad boundaries.

South Philadelphia passive sampler and sensor study

From June 2013 to March 2015, in total 41 passive sampler deployments of 2 wk duration each were conducted at 17 sites in South Philadelphia, PA, with results for benzene discussed here. Complementary time-resolved measurements with lower cost prototype fenceline sensors and an open-path ultraviolet differential optical absorption spectrometer were also conducted. Minimum passive sampler benzene concentrations for each sampling period ranged from 0.08 ppbv to 0.65 ppbv, with a mean of 0.25 ppbv, and were negatively correlated with ambient temperature (-0.01 ppbv/°C, R² = 0.68). Co-deployed duplicate passive sampler pairs (N = 609) demonstrated good precision with an average and maximum percent difference of 1.5% and 34%, respectively. A group of passive samplers located within 50 m of a refinery fenceline had a study mean benzene concentration of 1.22 ppbv, whereas a group of samplers located in communities >1 km distant from facilities had a mean of 0.29 ppbv. The difference in the means of these groups was statistically significant at the 95% confidence level (p < 0.001). A decreasing gradient in benzene concentrations moving away from the facilities was observed, as was a significant period-to-period variation. The highest recorded 2-wk average benzene concentration for the fenceline group was 3.11 ppbv. During this period, time-resolved data from the prototype sensors and the open-path spectrometer detected a benzene signal from the west on one day in particular, with the highest 5-min path-averaged benzene concentration measured at 24 ppbv.

IMPLICATIONS

Using a variation of EPA's passive sampler refinery fenceline monitoring method, coupled with time-resolved measurements, a multiyear study in South Philadelphia informed benzene concentrations near facilities and in communities. The combination of measurement strategies can assist facilities in identification and mitigation of emissions from fugitive sources and improve information on air quality complex air sheds.