Vertically Segregated Polymer Blends: Their Use in Organic Electronics

Polyethylene and Semiconducting Polymer Blends for the Fabrication of Organic Field-Effect Transistors: Balancing Charge Transport and Stretchability

Polyethylene is amongst the most used polymers, finding a plethora of applications in our lives owing to its high impact resistance, non-corrosive nature, light weight, cost effectiveness, and easy processing into various shapes from different sizes. Despite these outstanding features, the commodity polymer has been underexplored in the field of organic electronics. This work focuses on the development of new polymer blends based on a low molecular weight linear polyethylene (LPE) derivative with a high-performance diketopyrrolopyrrole-based semiconducting polymer. Physical blending of the polyethylene with semiconducting polymers was performed at ratios varying from 0 to 75 wt.%, and the resulting blends were carefully characterized to reveal their electronic and solid-state properties. The new polymer blends were also characterized to reveal the influence of polyethylene on the mechanical robustness and stretchability of the semiconducting polymer. Overall, the introduction of LPE was shown to have little to no effect on the solid-state properties of the materials, despite some influence on solid-state morphology through phase separation. Organic field-effect transistors prepared from the new blends showed good device characteristics, even at higher ratios of polyethylene, with an average mobility of 0.151 cm2 V−1 s−1 at a 25 wt.% blend ratio. The addition of polyethylene was shown to have a plasticizing effect on the semiconducting polymers, helping to reduce crack width upon strain and contributing to devices accommodating more strain without suffering from decreased performance. The new blends presented in this work provide a novel platform from which to access more mechanically robust organic electronics and show promising features for the utilization of polyethylene for the solution processing of advanced semiconducting materials toward novel soft electronics and sensors.

Interface Engineering in Organic Field-Effect Transistors: Principles, Applications, and Perspectives

Heterogeneous interfaces that are ubiquitous in optoelectronic devices play a key role in the device performance and have led to the prosperity of today's microelectronics. Interface engineering provides an effective and promising approach to enhancing the device performance of organic field-effect transistors (OFETs) and even developing new functions. In fact, researchers from different disciplines have devoted considerable attention to this concept, which has started to evolve from simple improvement of the device performance to sophisticated construction of novel functionalities, indicating great potential for further applications in broad areas ranging from integrated circuits and energy conversion to catalysis and chemical/biological sensors. In this review article, we provide a timely and comprehensive overview of current efficient approaches developed for building various delicate functional interfaces in OFETs, including interfaces within the semiconductor layers, semiconductor/electrode interfaces, semiconductor/dielectric interfaces, and semiconductor/environment interfaces. We also highlight the major contributions and new concepts of integrating molecular functionalities into electrical circuits, which have been neglected in most previous reviews. This review will provide a fundamental understanding of the interplay between the molecular structure, assembly, and emergent functions at the molecular level and consequently offer novel insights into designing a new generation of multifunctional integrated circuits and sensors toward practical applications.

Recent Progress in High-Mobility Organic Transistors: A Reality Check

Over the past three decades, significant research efforts have focused on improving the charge carrier mobility of organic thin-film transistors (OTFTs). In recent years, a commonly observed nonlinearity in OTFT current-voltage characteristics, known as the "kink" or "double slope," has led to widespread mobility overestimations, contaminating the relevant literature. Here, published data from the past 30 years is reviewed to uncover the extent of the field-effect mobility hype and identify the progress that has actually been achieved in the field of OTFTs. Present carrier-mobility-related challenges are identified, finding that reliable hole and electron mobility values of 20 and 10 cm2 V-1 s-1 , respectively, have yet to be achieved. Based on the analysis, the literature is then reviewed to summarize the concepts behind the success of high-performance p-type polymers, along with the latest understanding of the design criteria that will enable further mobility enhancement in n-type polymers and small molecules, and the reasons why high carrier mobility values have been consistently produced from small molecule/polymer blend semiconductors. Overall, this review brings together important information that aids reliable OTFT data analysis, while providing guidelines for the development of next-generation organic semiconductors.

Conjugated-Polymer Blends for Organic Photovoltaics: Rational Control of Vertical Stratification for High Performance

The photoactive layer of bulk-heterojunction organic solar cells, in a thickness range of tens to hundreds of nanometers, comprises phase-separated electron donors and acceptors after solution casting. The component distribution in the cross-section of these thin films is found to be heterogeneous, with electron donors or acceptors accumulated or depleted near the electrode interfaces. This vertical stratification of the photovoltaic blend influences device metrics through its impact on charge transport and recombination, and consequently plays an important role in determining the power conversion efficiency of photovoltaic devices. Here, different techniques, e.g., surface analysis and sputter-assisted depth-profiling, reflectivity modeling, and 3D imaging, that have been employed to characterize vertical stratification in bulk-heterojunction photovoltaic blends are reviewed. The origins of vertical stratification are summarized, including thermodynamics, kinetics, surface free energy, and selective dissolubility. The impact of correct and wrong vertical stratification to device metrics of solar cells are highlighted. Examples are then given to demonstrate how desired vertical stratification can be controlled with properly aligned device architecture to enable solar cells with high efficiency.

Solution processed thick film organic solar cells

In this Review article, significant advances in materials development and processing methods toward efficient solution processed bulk-heterojunction thick film organic solar cells as well as the factors that determine the optimal active layer thickness are summarized.

Facile preparation of concentration-gradient materials with radical spin of the mixed-valence tetrathiafulvalene in conventional polymer films

We describe here the facile methods for the stepwise regulation of the formation of tetrathiafulvalene (TTF) radical cation and the self-assembly to the mixed-valence state of TTF in various polymer films. The homogeneous polymer composites containing TTF and (1R)-3,3-dimethylbicyclo[2.2.1]hepta-2-one-1-triflate as a photoinduced acid generator in several kinds of conventional polymers were prepared, and the phototriggered conversion of TTF to radical cation via protonation in the films was executed. The amount of the TTF radical species can be controlled by the length of UV-irradiation time to the polymer composite films. In addition, the formation of the mixed-valence TTF can be observed in the composite films by annealing after UV irradiation when the glass transition temperature of the matrices was sufficiently higher than the reaction temperature during the photoirradiation. Finally, we presented the facile patterning method for preparing the composite with the concentration gradient of TTF radical and the mixed-valence TTF.

Controlling film morphology in conjugated polymer:fullerene blends with surface patterning

We study the effects of patterned surface chemistry on the microscale and nanoscale morphology of solution-processed donor/acceptor polymer-blend films. Focusing on combinations of interest in polymer solar cells, we demonstrate that patterned surface chemistry can be used to tailor the film morphology of blends of semiconducting polymers such as poly-[2-(3,7-dimethyloctyloxy)-5-methoxy-p-phenylenevinylene] (MDMO-PPV), poly-3-hexylthiophene (P3HT), poly[(9,9-dioctylflorenyl-2,7-diyl)-co-benzothiadiazole)] (F8BT), and poly(9,9-dioctylfluorene-co-bis-N,N'-(4-butylphenyl)-bis-N,N'-phenyl-1,4-phenylendiamine) (PFB) with the fullerene derivative, [6,6]-phenyl-C(61)-butyric acid methyl ester (PCBM). We present a method for generating patterned, fullerene-terminated monolayers on gold surfaces and use microcontact printing and Dip-Pen Nanolithography (DPN) to pattern alkanethiols with both micro- and nanoscale features. After patterning with fullerenes and other functional groups, we backfill the rest of the surface with a variety of thiols to prepare substrates with periodic variations in surface chemistry. Spin coating polymer:PCBM films onto these substrates, followed by thermal annealing under nitrogen, leads to the formation of structured polymer films. We characterize these films with Atomic Force Microscopy (AFM), Raman spectroscopy, and fluorescence microscopy. The surface patterns are effective in guiding phase separation in all of the polymer:PCBM systems investigated and lead to a rich variety of film morphologies that are inaccessible with unpatterned substrates. We demonstrate our ability to guide pattern formation in films thick enough to be of interest for actual device applications (up to 200 nm in thickness) using feature sizes as small as 100 nm. Finally, we show that the surface chemistry can lead to variations in film morphology on length scales significantly smaller than those used in generating the original surface patterns. The variety of behaviors observed and the wide range of control over polymer morphology achieved at a variety of different length scales have important implications for the development of bulk heterojunction solar cells.