Removal of thallium (I) by activated carbon prepared from apricot nucleus shell and modified with rhodamine B

Cultivation of autotrophic nitrifying granular sludge for simultaneous removal of ammonia nitrogen and Tl(I)

Autotrophic nitrifying granular sludge (ANGS) was cultivated for the simultaneous removal of ammonia nitrogen and Tl(I) from inorganic wastewater. The chemical oxygen demand (COD) in the influent gradually decreased to approximately zero in four parallel sequencing batch reactors (B1: blank controller, B2: 10 mL of added nitrifying bacteria concentrate in each cycle, B3: 1 mg/L Tl(I) added in each cycle and B4: 10 mL of added nitrifying bacteria concentrate and 1 mg/L Tl(I) in each cycle) within 15 days. The main properties, such as the granulation rate and specific oxygen uptake rate (SOUR) of the ANGS in B1, B2, B3 and B4 tended to be stable within 40, 33, 30 and 33 days, the removal efficiencies of Tl(I) were 59.5%-82.9% and 57.1%-88.6% in B3 and B4 after Day 30, the removal efficiencies of ammonia nitrogen in B1, B2, B3 and B4 were usually above 90% after Day 33, and the total inorganic nitrogen (TIN) in the effluent of B1, B2, B3 and B4 gradually stabilized after Day 36, 32, 32 and 36, indicating that mature ANGS was successfully cultivated in B1, B2, B3 and B4 within 40, 33, 33 and 36 days. The nitrogen degradation kinetic parameters of ANGS indicated that B3 had the strongest ability to remove ammonia and nitrite, suggesting that Tl(I) stress was beneficial to ammonia nitrogen removal and nitrite oxidation. The adsorption of Tl(I) can be described by the Freundlich equation, and the addition of external nitrifying bacteria improved the adsorption ability of ANGS.

Recent Advances in Thallium Removal from Water Environment by Metal Oxide Material

Thallium is widely used in industrial and agricultural development. However, there is still a lack of systematic understanding of its environmental hazards and related treatment methods or technologies. Here, we critically assess the environmental behavior of thallium in aqueous systems. In addition, we first discuss the benefits and limitations of the synthetic methods of metal oxide materials that may affect the practicality and scalability of TI removal from water. We then assess the feasibility of different metal oxide materials for TI removal from water by estimating the material properties and contaminant removal mechanisms of four metal oxides (Mn, Fe, Al, and Ti). Next, we discuss the environmental factors that may inhibit the practicality and scalability of Tl removal from water. We conclude by highlighting the materials and processes that could serve as more sustainable alternatives to TI removal with further research and development.

Removal of Thallium from Aqueous Solutions by Adsorption onto Alumina Nanoparticles

Thallium (I) was removed from aqueous solution by using gamma-alumina nanoparticles (γANPs) materials as nano adsorbents. Varied experimental conditions such as adsorbent dose, agitation time, initial concentration, pH, and temperature effects were carried out in batch conditions in view of the optimization of thallium (I) adsorption and the identification of the adsorption mechanisms in the system γANPs-Tl. The pH effect indicated a remarkable increase in the quantity of Tl(I) removed for pH values ranging from 4 to 8, an almost constant magnitude for pH values between 8 and 10, and a decrease for pH values above 10. Considering an initial Tl(I) concentration of 20 µg/L and an adsorbent dose of 1 g/L at a pH value of 8.5, the removal was achieved at 95.12 ± 0.02% efficiency. The pseudo-second-order kinetics and the Freundlich isotherm perfectly described the adsorption mechanism. The process of thallium (I) adsorption reaction, as highlighted by thermodynamic investigations, was found to be spontaneous and exothermic with coexistence of physisorption and chemisorption with a dominance of physisorption. The diffusion model predicted multi-linearity, suggesting an involvement of surface spread and intraparticle diffusion in the sorption process. Thallium removal was effective by using γANPs as nano adsorbents.

Adsorptive behavior of thallium using Fe3O4-kaolin composite synthesized by a room temperature ferrite process

Thallium (Tl) contaminants pose serious threats to the ecological environment and human health due to its acute/chronic poisoning on the health of most organisms even at low concentrations. To find a rapid and efficient technology in removing Tl from waters thus becomes a crucial issue. A magnetic Fe₃O₄-kaolin composite (denoted by FKC) with high specific surface area (133.7 m²/g) was successfully synthesized via a simple and low-cost technique for Tl(I) removing from various water media. The HRTEM images confirmed the existence of lattice fingers Fe₃O₄ and displayed that a large number of Fe₃O₄ nanoparticles dispersed on the surface of kaolin sheets. Compared with kaolin or Fe₃O₄ alone, FKC enhanced obviously the adsorption rate and capacity of Tl(I) over a wide pH range (4.5-9.0). The maximum adsorption capacity of FKC for Tl(I) was 19,347 mg/kg (calculated by Langmuir model), which was almost one hundred times and two times higher than those of kaolin and Fe₃O₄, respectively. Importantly, FKC was observed to have a great potential in removing Tl(I) from surface water, groundwater, and tap water in more alkaline conditions. By applying the external magnetic field, FKC could be recovered efficiently (99%) and rapidly (20 s). Moreover, Tl L₃-edge XANES spectra revealed that Tl(I) was adsorbed on the FKC and would not be converted to more toxic Tl(III). The cations (CaCl₂, NaCl, and KCl) and the ionic strength with concentrations of 0.001-1.0 mol/L showed a great influence on the adsorption of Tl(I) by FKC, implying that this adsorption was dominated by outer-sphere surface complexation at investigated pH values. The information provided is essential for designing a rapid and effective scavenger for removing Tl in various natural waters.

Removing Pollutants from Sewage Waters with Ground Apricot Kernel Shell Material

For the first time, a comprehensive review of the literature data on the use of apricot (Prunus armeniaca) biomass components as a sorption material for the treatment of wastewater and environmental water from various pollutants is carried out in the present study. In addition to a comprehensive analysis of contemporary studies, the current work carried out its own microstructural and energy dispersive studies. It shows that apricot kernel shell is a promising raw material for obtaining sorption materials that can be used to extract various pollutants from aqueous media. The parameters of sorption interaction are presented, at which the highest rate of removal of pollutants was achieved. It is shown that the sorption capacity of apricot biomass components can be increased by modifying it with various chemical reagents, as well as other physical and physicochemical methods. We reveal that most publications consider the use of the latter as a raw material for the production of activated carbons. It is established that the surface area and total pore space of activated carbons from apricot kernel shells depend on the modes of carbonization and activation. It is shown that activated carbons are effective adsorbents for removing various pollutants (metal ions, dyes, oil and oil products) from aqueous media. It was found that the adsorption isotherms of pollutants in most cases are best described by the Langmuir and Freundlich models, and the process kinetics is most often described by the pseudo-second-order model. The possibility of improving the sorption characteristics of apricot biomass during chemical or physicochemical treatment is also shown.

Assessment of the Ecotoxicity of Pollution by Potentially Toxic Elements by Biological Indicators of Haplic Chernozem of Southern Russia (Rostov region)

The content of various chemical elements such as metals, metalloids, and nonmetals in the environment is associated with natural and anthropogenic sources. It is necessary to normalize the content of metals, metalloids, and nonmetals as potentially toxic elements (PTE) in the Haplic Chernozem. The soils of the Southern Russia are of high quality and fertility. However, this type of soil, like Haplic Chernozem, is subject to contamination with a wide range of PTE. The aim of the work was to rank metals, metalloids, and nonmetals by ecotoxicity in Haplic Chernozem. To assess the ecotoxicity of chernozem, data for 15 years (2005-2020) were used. Biological indicators used to assess the ecotoxicity of Haplic Chernozem: catalase activity, cellulolytic activity, number of bacteria, Azotobacter spp. abundance, to change of length of radish's roots. Based on these biological indicators, an integral indicator of the state of Haplic Chernozem was calculated. The ecotoxicity of 23 metals (Cd, Hg, Pb, Cr, Cu, Zn, Ni, Co, Mo, Mn, Ba, Sr, Sn, V, W, Ag, Bi, Ga, Nb, Sc, Tl, Y, Yb), 5 metalloids (B, As, Ge, Sb, Te) and 2 nonmetals (F, Se) as priority pollutants. It is proposed to distinguish three hazard classes of metals, metalloids, and nonmetals to Haplic Chernozem: I class - Te, Ag, Se, Cr, Bi, Ge, Sn, Tl, Hg, Yb, W, Cd; II class - As, Co, Sc, Sb, Cu, Ni, B, Nb, Pb, Ga; III class - Sr, Y, Mo, Zn, V, Ba, Mn, F. It is advisable to use the results of the study for predictive assessment of the impact of metals, metalloids, and nonmetals on the ecological state of the soil during pollution.

Highly efficient removal of thallium in wastewater by MnFe2O4-biochar composite

Thallium (Tl), is a highly toxic trace metal in the natural environment. Emerging Tl pollution in waters has gradually become a global concern. However, limited removal technologies are available for Tl-containing wastewater. Herein, MnFe₂O₄-biochar composite (MFBC) was successfully fabricated via coprecipitation method as a novel and efficient adsorbent for treating Tl(I)-contaminated wastewater. It was found that the MFBC, with a specific surface area of 187.03 m²/g, exhibited high performance across a wide pH range of 4-11, with the superior Tl(I) removal capacity (170.55 mg/g) based on Langmuir model (pH 6.0, a dosage of 1 g/L). The removal mechanisms included physical and chemical adsorption, ion exchange, surface complexation, and oxidation. This investigation revealed that MFBC is a promising and environmentally friendly adsorbent with a low cost, large specific surface area, magnetic properties, and high efficiency for the removal of Tl(I) from wastewater.

Extensive removal of thallium by graphene oxide functionalized with aza-crown ether

Thallium (Tl) is a highly toxic heavy metal, and its pollution and remediation in aquatic environments has attracted considerable attention. To reduce or remove Tl pollution in the environment, various strategies have been applied. Graphene oxide (GO) has abundant oxygen-containing functional groups, indicating its high application potential for pollution remediation via methods involving binding to metal ions or positively charged organic molecules or electrostatic interaction and coordination. However, the adsorption of Tl to GO occurs via physical adsorption, for which the adsorption efficiency is low. Therefore, herein, we report a new method to effectively remove Tl pollution in water. We combined GO with aza-crown ether, which enhanced the electronegativity and ability to bind metal ions. The functionalized graphene oxide (FGO) demonstrated high efficiency through a wide pH gradient of 5-10, with a dominant Tl(i) adsorption capacity (112.21 mg g-1) based on the Langmuir model (pH 9.0, adsorbent concentration of 0.8 g L-1). The adsorption of Tl(i) during removal fit a pseudo-second-order kinetic model well. The mechanisms of Tl removal involve physical and chemical adsorption. In summary, our study provides a new method for the detection and treatment of Tl-containing wastewater by using FGO.

Fabrication and characterization of magnetically responsive Fe3O4@TiO2 core-shell adsorbent for enhanced thallium removal

Thallium (Tl) contamination in natural waters can pose a severe risk to human health. In this study, a magnetically responsive Fe₃O₄@TiO₂ core-shell adsorbent was developed for the effective removal of thallium(I) from water. The isoelectric point of the adsorbent surface was decreased from 6.0 to 4.8 due to the loading of nano-sized TiO₂, leading to an enhanced electrostatic interaction between the adsorbent and Tl(I) ions in a wider pH range. The Fe₃O₄@TiO₂ magnetic adsorbent exhibited a threefold higher BET specific surface area compared to pristine Fe₃O₄ particles. The kinetics study showed that approximately 82% of the maximum Tl(I) loading amount could be achieved within 30 min at the initial Tl(I) concentration of 8 mg/L and adsorbent dosage of 0.1 g/L. The adsorption of Tl(I) was significantly increased with increasing solution pH. The experimental data was better fitted by the Langmuir and Temkin isotherms than the Freundlich isotherm and the maximum adsorption capacity of the magnetic adsorbent was 101.5 mg/g at pH 7.0. The interference of co-existing cations in the Tl(I) adsorption followed the subsequence: Cu²⁺ > Mg²⁺ > Ca²⁺ > Na⁺. The hydroxyl groups bonded on titanium atoms might play a key role in the uptake of Tl(I) ions. During the adsorption, the Tl(I) ions can be effectively adsorbed on the adsorbent surface via the formation of Ti-O-Tl linkages. Graphical Abstract.

High-efficiency adsorption and regeneration of methylene blue and aniline onto activated carbon from waste edible fungus residue and its possible mechanism

Edible fungus residue as an efficient and low-cost precursor was used to produce Edible Fungus residue Activated Carbon (EFAC) using the zinc chloride activation method at a 1 : 2 impregnation ratio and 600 °C activation for 3 hours. The activation process does not need gases like nitrogen and is suitable for mass production. Fungal biodegradation facilitates efficient chemical activation, which might have generated abundant pores on the activated carbon sample. Using BET, X-ray diffraction (XRD), scanning electron microscopy (SEM), and FTIR characterization, reveals that EFAC exhibits a large specific surface area (1070 m² g⁻¹), and large pore volume (0.68 cm³ g⁻¹), with its surface displaying a honeycomb-like structure. The EFAC adsorbs methylene blue (MB) and aniline in water, with maximum adsorptions of 662.25 and 27.10 mg g⁻¹, respectively. Various adsorption conditions, such as the EFAC dosage, pH, contact time and initial concentration were investigated. The adsorption is characterized by the pseudo-second-order kinetic and Langmuir isotherm models, with thermodynamics studies indicating that the adsorption is endothermic and spontaneous. Furthermore, the EFAC exhibited good regeneration performance by a 90% ethanol solution. The EFAC is a low-cost and environmentally friendly adsorbent for removing organic contaminants in wastewater.

Edible fungus residue as an efficient and low-cost precursor was used to produce Edible Fungus residue Activated Carbon (EFAC) using the zinc chloride activation method at a 1 : 2 impregnation ratio and 600 °C activation for 3 hours.

Removal of thallium in water/wastewater: A review

The frequent occurrence of thallium (Tl) in surface water has led to the imposition of strict environmental regulations. The need for an overview of effective and feasible technology to remove Tl from water/wastewater has therefore become urgently. This review introduced the current available methods for Tl removal, including adsorption, oxidation-reduction precipitation, solvent extraction and ion exchange processes, and summarized their advantages and disadvantages. The results showed that a single treatment technology was difficult to remove Tl to a trace level of "μg L^-1", which required combined multi-technology to enhance the removal efficiency. In addition, the potential emergency and feasible technologies for Tl removal were recommended. However, several fundamental issues, such as the comparative toxicity of Tl(I) and Tl(III), the confliction of hydrolysis constants, the interference of complexant ligands as well as the influence of redox potential, were still needed to be addressed, since they would profoundly affect the selection of adopted treatment methods and the behavior of Tl removal. Future research efforts concerning the improvement of existing Tl removal technologies should be devoted to (a) developing multi-functional chemicals and adsorbents, non-toxic extractants, easy-recovery ion exchange resin and high-efficient coupling technology for advanced treatment, (b) carrying out large-scale experiments and economic assessment for real wastewater, and (c) providing safe-disposal treatment for the exhausted adsorption materials or sludge.

Removal of thallium from environmental samples using a raw and chemically modified biosorbent derived from domestic wastes

Because of its high toxicity, thallium (Tl) causes environmental pollution even at very low concentrations. Despite its extremely high environmental risk, limited information about Tl removal from water is present on the literature. This work focused on the use of an eco-friendly and low-cost Ilex paraguariensis (yerba mate) biowaste to remove Tl from environmental water samples. Raw (YM) and L-cysteine chemically modified yerba mate (YM@LC) were used. The effect of pH and biosorbent concentration on the biosorption capacity was studied using an experimental design. The optimal experimental conditions were as follows: YM concentration 0.25 g L^-1, pH 6.0, and YM@LC concentration 0.25 g L^-1, pH 4.0. Kinetic studies yielded data that were in accordance with pseudo-second-order model. Equilibrium studies were also developed and indicated that the most appropriate model was that of Sips, with a maximum capacity of biosorption at 328 K of 333.4 mg g^-1 for YM and 384.4 mg g^-1 for YM@LC. The thermodynamic evaluation exhibited an endothermic, spontaneous, and favorable biosorption for both biosorbents. YM and YM@LC showed significant potential for Tl removal from environmental water samples.