Copolyethersulfones of 1,4:3,6-dianhydrohexitols and bisphenol A

A Sensitive Impedimetric Sensor Based on Biosourced Polyphosphine Films for the Detection of Lead Ions

In this work, impedimetric sensors were developed for the detection of the four WFD heavy metals Pb2+, Cd2+, Hg2+ and Ni2+, by the modification of a gold electrode with four partially biosourced polyphosphine polymers. These polymers were obtained with satisfactory yields by polycondensation of the bis(4-fluorophenyl)(4-methylphenyl)phosphine sulfide and the bis(4-fluorophenyl)(4-methylphenyl)phosphine oxide using isosorbide or bisphenol A. The chemical structures and number-average molecular weights of the resulting polymers were determined by NMR spectroscopy (1H, 19F, and 31P) and by size exclusion chromatography. Glass transition temperatures varied between 184 and 202 °C depending on the composition of polymers. The bio-based poly(etherphosphine) oxide modified sensor showed better analytical performance than petrochemical based oxide for the detection of Pb2+. A detection limit of 10−10 g/L or 0.5 pM, which is 104 times lower than that of the anodic stripping voltammetric and the potentiometric sensors. A reversibility is obtained through rinsing of the impedimetric sensor with an EDTA solution.

Study on the Synthetic Characteristics of Biomass-Derived Isosorbide-Based Poly(arylene ether ketone)s for Sustainable Super Engineering Plastic

Demand for the development of novel polymers derived from biomass that can replace petroleum resources has been increasing. In this study, biomass-derived isosorbide was used as a monomer in the polymerization of poly(arylene ether ketone)s, and its synthetic characteristics were investigated. As a phase-transfer catalyst, crown ether has increased the weight-average molecular weight of polymers over 100 kg/mol by improving the reaction efficiency of isosorbide and minimizing the effect of moisture. By controlling the experimental parameters such as halogen monomer, polymerization solvent, time, and temperature, the optimal conditions were found to be fluorine-type monomer, dimethyl sulfoxide, 24 h, and 155 °C, respectively. Biomass contents from isosorbide-based polymers were determined by nuclear magnetic resonance and accelerator mass spectroscopy. The synthesized polymer resulted in a high molecular weight that enabled the preparation of transparent polymer films by the solution casting method despite its weak thermal degradation stability compared to aromatic polysulfone. The melt injection molding process was enabled by the addition of plasticizer. The tensile properties were comparable or superior to those of commercial petrochemical specimens of similar molecular weight. Interestingly, the prepared specimens exhibited a significantly lower coefficient of thermal expansion at high temperatures over 150 °C compared to polysulfone.

Microwave-assisted synthesis of isosorbide-derived diols for the preparation of thermally stable thermoplastic polyurethane

In order to prepare thermally stable isosorbide-derived thermoplastic polyurethane, the synthesis of two new chiral exo-exo configured diols, prepared from isosorbide, and two types of diphenols (bisphenol A and thiodiphenol) was described. The synthesis conditions were optimized under conventional heating and microwave irradiations. To prove their suitability in polymerization, these monomers were successfully polymerized using 4,4'-diphenylmethane diisocyanate (MDI) and hexamethylene diisocyanate (HDI). Both monomers and polymers have been studied by NMR, FT-IR, TGA, DSC; intrinsic viscosity of polymers has also been determined. The results showed the effectiveness of the synthetic strategy proposed; moreover, a dramatic reduction of the reaction time and an important improvement of the monomers yield using microwave irradiation have been demonstrated. The monomers, as well as the polymers, showed excellent thermal stability both in air and nitrogen. It was also shown that the introduction of sulphur in the polyurethane backbone was effective in delaying the onset of degradation as well as the degradation rate.

Bio-Based Poly(Ether Imide)s from Isohexide-Derived Isomeric Dianhydrides

In this work, four isohexide-derived isomeric dianhydrides were synthesized through a four-step procedure using isohexide and chloro-N-phenylphthalimides as the starting materials. The one-step solution polymerization of these dianhydrides with petroleum- or bio-based diamines enabled the synthesis of poly(ether imide)s (PEIs), which had viscosities of 0.41 to 2.40 dL∙g-1. The isohexide-derived PEIs were characterized based upon their solubility and their thermal, mechanical, and optical properties. The results showed that most of the isohexide-derived PEIs possessed comparable glass transition temperatures (Tg), tensile strengths, and moduli to petroleum-based PEIs. However, the thermo-oxidative stability of the PEIs was found to be lower than that of the common petroleum-based PEIs. Moreover, the PEIs displayed good optical activity, which originated from their unique chiral isohexide moieties. The isomeric effects of dianhydride monomers on the properties of the resulting PEIs were comparatively studied. The results suggested that the corresponding 4,4'-linked PEIs possessed lower Tg, higher mechanical properties, and higher specific rotations compared to 3,3'-linked polymers. Meanwhile, the polyimides with isomannide residue displayed higher Tg and more specific rotations than the corresponding polymers with isosorbide residue. These results contributed to more restricted rotations of phthalimide segments in 3,3'-linked or isomannide containing polyimides.